Antunes HCT-2000 Owner's Manual

Horizontal contact toaster

Advertisement

Quick Links

Horizontal Contact Toaster
Model HCT-2000
owner's manual
Manufacturing Numbers:
9210322
www.antunes.com
P/N 1011369 Rev. B 07/17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HCT-2000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Antunes HCT-2000

  • Page 1 Horizontal Contact Toaster Model HCT-2000 owner’s manual Manufacturing Numbers: 9210322 www.antunes.com P/N 1011369 Rev. B 07/17...
  • Page 2: Table Of Contents

    Fill in the information below and have it materials available and assembled to our strict Operating Instructions ......5 handy when calling Antunes Technical Service quality standards. This unit has been tested at Light/Dark Adjustments ......6 for assistance. The serial number is on the the factory to ensure dependable trouble-free User Mode..........
  • Page 3: Important Safety Information

    • This equipment should be serviced • If a chemical cleaner is used, be sure by qualified personnel only. Contact it is safe to use on cast aluminum. Antunes Technical Service for adjust- ment or repair. Observe all precautions and warnings on product label.
  • Page 4: Specifications

    SPECIFICATIONS Model & Width Depth Height Mfg. No. HCT-2000 20 25/32” 26 30/32 18 13/32” 9210322 (523 mm) (684 mm) (467 mm) Plug Model Volts Watts Amps Hertz Configuration Description 6-20P HCT-2000 2400 50/60 20 Amp., 250 Volt 9210322 Right Angle...
  • Page 5: Installation

    • Three Release Sheets front of the unit. NOTE: If any parts are missing or dam- 5. Attach the Bun Feeder. aged, contact Antunes Customer Service Figure 1. Installing Release Sheet IMPORTANT: Do not plug any other power IMMEDIATELY at +1-877-392-7856 (toll cords into the receptacles on the toaster.
  • Page 6: Light/Dark Adjustments

    LIGHT/DARK ADJUSTMENTS 7. Press the PROGRAM button to pro- ceed to the Motor Speed Setpoint. The light/dark value can be adjusted when the 8. Adjust the Motor Speed Setpoint by unit is displaying “LO” or “USE”. To adjust pressing the LIGHTER or DARKER the light/dark value, press the LIGHTER or buttons to reach the desired speed.
  • Page 7: Safety Features

    SAFETY FEATURES ERROR CODES A Hi-Limit Control turns off electric power If any of the following Error Codes appear, turn to the heaters and control circuits if the unit the power off, allow the unit to cool, and turn overheats. To reset the control, allow 10-15 the power back on.
  • Page 8: Recommended Settings

    Platen Heater - 570°F (299°C) Auxiliary Heater - 400°F (204°C) Motor Speed - 67 Corporate Headquarters China Facility Antunes delivers a complete range of countertop cooking Carol Stream, Illinois Suzhou, China equipment and water filtration solutions to foodservice Phone: (630) 784-1000 Phone: 86-512-6841-3637 operations around the world.
  • Page 9: Daily Maintenance

    • Fill a clean 1/6-size, 6-inch deep s/s WARNING pan with hot Detergent Solution; a sec- Turn the power off, unplug the power cord, and ond pan with clean rinse water; and a third pan with Sanitizer Solution. Place all the unit to cool down for 30 minutes before a clean, white towel in each pan and performing any service or maintenance.
  • Page 10: Replacing The Release Sheet (Every 3-5 Weeks)

    WARNING Silicone Belt Flap Silicone Belt Teeth Align the ends of the Silicone Belt properly (Figure 7) or the belt may be damaged. WARNING The unit can retain heat. Be sure to wear Heat- Resistant Gloves to avoid personal injury. INCORRECT CORRECT Figure 7.
  • Page 11: Checking The Conveyor Belt Chain (Every 3-6 Months)

    CHECKING THE CONVEYOR REPLACING CONVEYOR BELT CHAIN Conveyor Belt Chain BELT CHAIN 1. Turn the unit off, unplug the power (EVERY 3–6 MONTHS) cord, and allow the unit to cool. Set the Bun Thickness Adjustment Control MEASURING CONVEYOR BELT CHAIN to 7.
  • Page 12: Troubleshooting

    TROUBLESHOOTING Problem Possible Cause Corrective Action Control Display flashes “LO” continu- Platen temperature is below 440ºF (226ºC). Allow the unit to warm up for 30 minutes and then ously. Buns not toasting properly. recheck. If the Control Display still reads “LO”, con- tact your maintenance person or Authorized Service Agency for service.
  • Page 13 TROUBLESHOOTING (continued) Problem Possible Cause Corrective Action No Control Display. Power cord not plugged in. Plug power cord into the proper electrical outlet. Hi-Limit Control has tripped. Allow unit to cool and reset the Hi-Limit Control. If it trips again, contact your maintenance person or Authorized Service Agency.
  • Page 14 TROUBLESHOOTING (continued) Problem Possible Cause Corrective Action Crowns and/or Heels must be forced Silicone Belt not being cleaned properly. Clean Silicone Belts as described in the into the toaster. Buns sticking and Maintenance section of this manual. burning. Silicone Belt are not tacky/sticky (replace every 2–4 Clean Silicone Belts.
  • Page 15: Replacement Parts

    REPLACEMENT PARTS AIR FLOW DIRECTION...
  • Page 16 REPLACEMENT PARTS (continued) 54 67...
  • Page 17 REPLACEMENT PARTS (continued) Item Part No. Description Qty. Item Part No. Description Qty. 0012619 Base Assembly 2150190 Sprocket, 25B28 1/2Bore Stepped Tooth 0012629 Elec. Panel Assembly 2150317 0013460 Platen Assembly 2150384 Bearing Assy, High Temp 0013461 Ctrl Housing Cover,Assy 1 1/8” Od X 1/2” Id 0013462 End Housing Cover Assy 2150421...
  • Page 18: Wiring Diagram

    WIRING DIAGRAM P/N 1011369 Rev. B 07/17...
  • Page 19: Notes

    NOTES P/N 1011369 Rev B 07/17...
  • Page 20: Limited Warranty

    LIMITED WARRANTY Equipment manufactured by A.J. Antunes & Co. (Antunes) has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from electrical and mechanical defects for a period of one (1) year from date of purchase under normal use and service, and when installed in accordance with manufacturer’s recommendations.

Table of Contents