Degelman rock rake RR1500 Operator's & Parts Manual
  1. Manuals
  2. Brands
  3. Degelman Manuals
  4. Farm Equipment
  5. rock rake RR1500
  6. Operator's & parts manual

Degelman rock rake RR1500 Operator's & Parts Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
D E G E L M A N
I N D U S T R I E S
B O X
8 3 0 - 2 7 2
I N D U S T R I A L
R E G I N A ,
S K ,
C A N A D A ,
F A X 3 0 6 . 5 4 3 . 2 1 4 0
P H 3 0 6 . 5 4 3 . 4 4 4 7
1 . 8 0 0 . 6 6 7 . 3 5 4 5
D E G E L M A N . C O M
L T D.
D R I V E ,
S 4 P
3 B 1
OPERATOR, ASSEMBLY
& PARTS MANUAL
PTO/HYDRAULIC MODELS
142274 v1.4
ROCK RAKE
RR1500

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the rock rake RR1500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Degelman rock rake RR1500

Summary of Contents for Degelman rock rake RR1500

  • Page 1 OPERATOR, ASSEMBLY & PARTS MANUAL 142274 v1.4 ROCK RAKE D E G E L M A N I N D U S T R I E S L T D. B O X 8 3 0 - 2 7 2 I N D U S T R I A L D R I V E , RR1500...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Introduction Safety Safety Information Safety Decal Locations Assembly Assembly Instructions Operation Preparation Machine Positioning Transporting Storage Maintenance & Service Service Adjustments Repair Troubleshooting Specifications Parts General Information Basic Components Hydraulic Components Drive Systems & Components Miscellaneous Warranty IMPORTANT: D E G E L M A N I N D U S T R I E S...

  • Page 5: Introduction

    Rock Rake will work well for many years. Safe, efficient and trouble free operation of your Degelman Rock Rake requires that you and anyone else who will be operating or maintaining the Rake, read and understand the Safety, Operation, Maintenance and Troubleshooting information contained within this manual.

  • Page 6: Safety

    CAUTION: Indicates a potentially hazardous situation CAUTION that, if not avoided, MAY result in minor or moderate injury if proper practices are not taken, or, serves as a reminder to follow appropriate safety practices. 142274 - Rock Rake RR1500 (22-September-2016)
  • Page 7 General Safety YOU are responsible for the safe operation and 1. Read and understand the Operator’s maintenance of your Degelman Rock Rake. YOU Manual and all safety signs before must ensure that you and anyone else who is going operating, maintaining or adjusting to operate, maintain or work around the Rock Rake the Rake.
  • Page 8 Keep others 1. Store unit in an area away from human activity. away. 2. Store machine with rake drum lowered. 3. Do not permit children to play around the stored unit. 142274 - Rock Rake RR1500 (22-September-2016)
  • Page 9 2. Do not attempt to mount a tire unless you have the proper equipment and experience to do the job. 3. Have a qualified tire dealer or repair service- man perform required tire maintenance. 142274 - Rock Rake RR1500 (22-September-2016)

  • Page 10: Safety Decal Locations

    • Think SAFETY! Work Safely! G 142359 - Decal, Warning-Rotating Part Hazard H 143264 - Decal, Important-Slip Clutch Safety Reflector Decals & Degelman Logo 142547 - Decal, Important-Disconnect Drive 142556 - Decal, Reflector Red - 2 x 9 142370 - Decal, Important-Secure Shield...
  • Page 11 119297 - Decal, Danger - Guard Missing (3) 142358 - Warning, 142359 - Warning, Rotating Part Hazard (2) Rotating Part Hazard (1) 143264 - Decal, Important - Slip Clutch (1) 142274 - Rock Rake RR1500 (30-November-2018)
  • Page 12 142547 - Decal, Important - Disconnect Drive (1) 142370 - Decal, Important - Secure Shield (1) 142369 - Decal, Important - Install Stop Bolt (1) 142368 - Decal, Important-Install Transport Pin (1) 142361 - Decal, Warning - Rotating Rake (3) 142274 - Rock Rake RR1500 (30-November-2018)
  • Page 13 Degelman follows the general Safety Standards specified by the American Society of Agricultural Engineers (ASAE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the Degelman Rock Rake must read and clearly understand ALL Safety, Operating and Maintenance information presented in this manual.

  • Page 14: Assembly

    (Note the direction of grease fitting.) Note: It is recommended to apply silicon sealer (supplied) to bearing flange surface before installing components. 142274 - Rock Rake RR1500 (22-September-2016) -10-...
  • Page 15 Store lock collar away for later assembly. Secure chain tightener assembly inside chain housing using the 5/8” x 2” bolts, lock washers and nuts shown. 142274 - Rock Rake RR1500 (22-September-2016) -11-...
  • Page 16 6. Pry and hold apart the rockshaft end plate and spiral drum to the gap shown. Install lock collar onto flange bearing. Use a hammer and drift punch to tighten securely (counter-clockwise). Secure lock collar by tightening setscrew. 142274 - Rock Rake RR1500 (22-September-2016) -12-...
  • Page 17 9. Lay main frame upon support and adjust over to align center lug on rockshaft to clevis plates on main frame. CAUTION: Be sure no one is standing near by while positioning components and check stands are secure before proceeding. 142274 - Rock Rake RR1500 (22-September-2016) -13-...
  • Page 18 5/8 in. UNC tap. Secure pin assembly using the flat washer, lock washer and bolt shown. 11. Install the safety stop bolt and high hex nut (fine thread) as shown into main frame plate. 142274 - Rock Rake RR1500 (22-September-2016) -14-...
  • Page 19 14. Swing both wheel legs over to align the hole with the center setting on pivot plate. Insert the bolt/clip assembly from bottom side and secure with the wing nut assem- bly. 142274 - Rock Rake RR1500 (22-September-2016) -15-...
  • Page 20 Note: Clean out threaded holes on casting using a 9/16 in. UNC tap. 16. Mount the hub/spindle assembly (straight) to the right hand wheel leg as illustrated, similar to step #15. 142274 - Rock Rake RR1500 (22-September-2016) -16-...
  • Page 21 Bolt Torque Chart on page #10. 19. Remove support stands. 20. Position the base bearing casting on rockshaft pipe and make ready the cap bearing casting along with two shims (slotted) as illustrated. 142274 - Rock Rake RR1500 (22-September-2016) -17-...
  • Page 22 Mate and secure the right hand castings last along with the remaining shield support bracket (slotted) and stone guard bracket using the two bolts, lock washers, and nuts shown. 142274 - Rock Rake RR1500 (22-September-2016) -18-...
  • Page 23 Slide unit onto gear box shaft ensuring a smooth sliding fit by coating surfaces with oil. 142274 - Rock Rake RR1500 (22-September-2016) -19-...
  • Page 24 Secure with the washer and bolt (drilled head) shown. Tighten bolt fully. Note: Grease fitting can be removed to ease assembly of bolt. 142274 - Rock Rake RR1500 (22-September-2016) -20-...
  • Page 25 30. Position the input shaft sprocket at the dis- tance shown from the inside of chain housing. Position lock collar onto end of shaft. (Continue to step 31) 142274 - Rock Rake RR1500 (22-September-2016) -21-...
  • Page 26 Tighten Evenly 2-3/16” 5. Locate and maintain the sprocket 2-3/16” (56 mm) (54mm) from inside chain housing while Tighten evenly tightening the three bolts. Clockwise (Continue to step 33). 142274 - Rock Rake RR1500 (22-September-2016) -22-...
  • Page 27 (clockwise). Secure lock collar by tightening the setscrew. 32. Tighten the other bearing lock collar (counter-clockwise) and secure collar by tightening setscrew. 33. Install the slider shaft unit onto shaft locations shown. 142274 - Rock Rake RR1500 (22-September-2016) -23-...
  • Page 28 (Torque to: - refer to 180 ft-lbs (245N.m) page 10) 35. Attach the opposite end of slider shaft unit to the gearbox and ensure full engagement of the quick disconnect yoke. 142274 - Rock Rake RR1500 (22-September-2016) -24-...
  • Page 29 2. Torch or cut-out excess material to allow for required hole size indicated by hole in template. 3. Clean/clear away debris and remove template. Install hydraulic motor and shield using 1/2” x 2-3/4” bolts and hardware. 142274 - Rock Rake RR1500 (22-September-2016) -25-...
  • Page 30 Note: It is recommended to apply silicon sealer (supplied) under cover plate and around bolt holes before installing. 7. Install appropriate hydraulic fittings. Hoses are shown but will be installed during a later step. 142274 - Rock Rake RR1500 (22-September-2016) -26-...
  • Page 31 Install and tighten the three bolts provided to secure the tapered bore sprocket to shaft. Note: Check to ensure that the 2-3/16 in. (55mm) dimension has been maintained when bolts are fully tightened. Loosen and repeat if necessary. 142274 - Rock Rake RR1500 (22-September-2016) -27-...
  • Page 32 (supplied) under cover plate and around bolt holes before installing. 42. Position the chain housing lid under the tab of chain housing. Thread in thumb screw and flat washer to secure lid. 142274 - Rock Rake RR1500 (22-September-2016) -28-...
  • Page 33 Tighten locknuts until approximately two threads of eyebolts protrude. CAUTION: Be sure no one is standing near when raising unit. Locate floating arm lock pin (25.4 dia. x 95 mm effective) in storage hole. 142274 - Rock Rake RR1500 (22-September-2016) -29-...
  • Page 34 Attach rock guard unit to collars of rock shaft and secure with bolts, lock washers and nuts in the two remaining open holes. Note: Be sure to install the drive shaft support bracket at this time, at location shown. 142274 - Rock Rake RR1500 (22-September-2016) -30-...
  • Page 35 49. Secure the front PTO shield to hitch pole using the two bolts, flat washers, lock washers and nuts shown. 50. Secure the flexible hose holder to the hitch pole using the bolt, flat washer, lock washer and nut indicated. 142274 - Rock Rake RR1500 (22-September-2016) -31-...
  • Page 36 52. Install the chain case input shaft shield over the bolt threads protruding from the flange bearing. Secure the shield with the two jam nuts shown. 142274 - Rock Rake RR1500 (22-September-2016) -32-...
  • Page 37 Align opposite end of drum shield to support bracket and insert the bolts only at this time 142274 - Rock Rake RR1500 (22-September-2016) -33-...
  • Page 38 56. Slide the third drum shield under the second, aligning holes shown. Secure shields with lock washers and nuts shown. Secure the opposite end to support bracket. Tighten all shield hardware left loose. 142274 - Rock Rake RR1500 (22-September-2016) -34-...
  • Page 39 Also use the plastic hose ties as shown. Note: Models with Hydraulic motor option requires 2 additional 3/4” hoses that mount with extra hose holder assemblies. 3/4 x 220 Hose Holder Hose (2) Hose Holders Hydraulic Motor 142274 - Rock Rake RR1500 (22-September-2016) -35-...
  • Page 40 Attach the appropriate quick couplers (not supplied) to the ends of these fittings. 62. Secure the safety chain unit to front of pole as shown using the bolt, lock washer and nut shown. 142274 - Rock Rake RR1500 (22-September-2016) -36-...
  • Page 41 Operator’s section of this manual. 65. The machine is now fully assembled and ready for operation. Be sure to read and understand fully the Operator’s sections of the manual before attaching machine to tractor. 142274 - Rock Rake RR1500 (22-September-2016) -37-...

  • Page 42: Operation

    Operation To the New Operator or Owner The Degelman Model RR1500 Rock Rakes are designed to efficiently windrow rocks from 2 to 12 inches (50 to 300 mm) diam- eter. Many of the features incorporated into this machine are the result of suggestions made by customers like you.
  • Page 43 14. Check the tire and insure that they are inflated to for both personal safety and maintaining the good the specified pressure: 32 psi (220kPa). mechanical condition of the Rake that this checklist be followed. 142274 - Rock Rake RR1500 (22-September-2016) -39-...

  • Page 44: Preparation

    Rake. In many cases, the spacing of the outer dual creates a tire track where the rock windrow is placed. This compacted tire track makes picking more difficult. 142274 - Rock Rake RR1500 (22-September-2016) -40-...
  • Page 45 6. Use the hitch pole jack to raise or lower the hitch to align with the drawbar. 7. Install a drawbar pin with provisions for a mechanical retainer such as a Klik pin. Install the retainer. 142274 - Rock Rake RR1500 (22-September-2016) -41-...
  • Page 46 (1) season or approximately sixty (60) days. This procedure can be found on page 78. 142274 - Rock Rake RR1500 (22-September-2016) -42-...
  • Page 47 13. Raise the Jack and rotate it 90º to place in its stowed position. 14. When unhooking from the tractor, reverse the above procedure. 15. Place the machine into the configuration appro- priate for the planned use. Refer to Pg.44-51 for configuration conversion procedures. 142274 - Rock Rake RR1500 (22-September-2016) -43-...

  • Page 48: Machine Positioning

    3. Remove pin from storage position hole and insert through the transport lugs to hold spiral drum in the raised position. 4. Check to make sure the “Slow Moving Vehicle (SMV)” emblem is facing the rear in line with the wheels. 142274 - Rock Rake RR1500 (22-September-2016) -44-...
  • Page 49 41. 2. Remove pin through transport lugs and place in its storage position. 3. Lower Spiral drum into its working position. 4. Swing the frame back into the field position. 142274 - Rock Rake RR1500 (22-September-2016) -45-...
  • Page 50 6. Retract cylinder to position spiral drum at right angles to hitch pole. 7. Remove suspension lock pin from its storage hole and install through floating arm. 8. Lower spiral drum to the ground and raise the wheels off the ground. 142274 - Rock Rake RR1500 (22-September-2016) -46-...
  • Page 51 9. Remove wing nut and bolt through each wheel leg. 10. Swing each wheel leg into its narrow transport position. Reinstall the bolts and tighten the wing nuts. 11. Raise spiral drum to its highest position. 142274 - Rock Rake RR1500 (22-September-2016) -47-...
  • Page 52 13. Extend hitch angling cylinder to move frame into the narrow transport configuration. 14. Reinstall safety stop bolt. 15. Check to make sure the SMV (Slow Moving Vehicle) emblem is facing the rear. 142274 - Rock Rake RR1500 (22-September-2016) -48-...
  • Page 53 1. Attach a tractor to the unit by following the pro- cedure outlined on pg. 41. 2. Remove safety stop bolt. 3. Retract hitch angling cylinder to position spiral drum square to the hitch pole. 142274 - Rock Rake RR1500 (22-September-2016) -49-...
  • Page 54 6. Remove the wing nut and bolt through each wheel leg. 7. Swing each wheel leg into its field position. Reinstall wheel leg bolt and tighten wing nut. 8. Raise spiral drum to lower wheels to the ground. 142274 - Rock Rake RR1500 (22-September-2016) -50-...
  • Page 55 12. Unfold and pin the hinged shield covering the cross driveline yoke. 13. Adjust the hitch pole to the appropriate angle for the work to be done. 142274 - Rock Rake RR1500 (22-September-2016) -51-...
  • Page 56 It is recommended that the teeth on the left end of the drum penetrate the ground about 1 inch (25mm). Soft soil conditions require a lighter floatation; Hard soil a heavier floata- tion. (Refer to page 66). 142274 - Rock Rake RR1500 (22-September-2016) -52-...
  • Page 57 It is recommended that the teeth on the left end of the drum penetrate the ground about 1 inch (25mm). Soft soil conditions require a lighter floatation; Hard soil a heavier floata- tion. (Refer to page 66). 142274 - Rock Rake RR1500 (22-September-2016) -53-...
  • Page 58 RPM and the ground speed be varied by changing gears in the tractor. A drum speed of 170 RPM will form the best rock windrow for gathering with a Degelman Rock Picker. d. Forward Speed The recommended ground speed varies from 2 to 6 mph (3.2-9.7 km/h) and is deter-...
  • Page 59 This will allow the drum to float over obstacles or ground contours during operation. 13. Pass over the field until the areas of the field with the rocks has been windrowed. 142274 - Rock Rake RR1500 (22-September-2016) -55-...

  • Page 60: Transporting

    8. Do not exceed 20 mph (32 km/h) when trans- porting. Never exceed a safe travel speed. Slow down when cornering or on rough roads. 9. Do not allow riders on the machine or tractor when transporting. 142274 - Rock Rake RR1500 (22-September-2016) -56-...

  • Page 61: Storage

    7. Oil the exposed rams on the hydraulic cylinders to prevent rusting. 8. Select an area that is dry, level and free of debris. 9. Follow the procedure given on page 41 when unhooking. 142274 - Rock Rake RR1500 (22-September-2016) -57-...

  • Page 62: Maintenance & Service

    4. If fittings will not take grease, remove and clean thoroughly. Also clean lubricant passageway. Replace fitting if necessary. 5. Inject grease until you see the grease being ex- pelled from the bearing or bushing areas. 142274 - Rock Rake RR1500 (22-September-2016) -58-...
  • Page 63 1. Lubricate Spiral Drum Hanger Bearings (3 locations). 2. Check the oil level in the chain drive reservoir. It should just touch the chain when the drum is rest- ing on the ground. Add as required. 142274 - Rock Rake RR1500 (22-September-2016) -59-...
  • Page 64 PTO Driveline (2 locations). Paint the inner telescoping shaft with grease. b. At Torque Limiter into Gearbox (1 locations). Cross Driveline (3 locations). 2. Check the oil level in the gearbox reservoir. Add as required. 142274 - Rock Rake RR1500 (22-September-2016) -60-...
  • Page 65 Maintenance & Service 25 Hours 1. Lubricate driveline hanger bearing (1 location). 2. Lubricate chain drive bearings (3 locations). 3. Lubricate spiral drum bearings (1 locations). 142274 - Rock Rake RR1500 (22-September-2016) -61-...
  • Page 66 4. Oil suspension system pivot pin. 50 Hours 1. Lubricate hitch jack. Note: Not all jacks are equipped with a grease fitting. 2. Lubricate wheel leg pivots (2 locations). 3. Lubricate center frame pivot (1 location). 142274 - Rock Rake RR1500 (22-September-2016) -62-...
  • Page 67 Maintenance & Service Annually 1. Repack wheel bearings. 2. Coat hydraulic cylinder rods with oil before storage. 142274 - Rock Rake RR1500 (22-September-2016) -63-...
  • Page 68 Maintenance & Service SERVICE RECORD See Lubrication and Maintenance sections for details of service. Copy this page to continue record. 142274 - Rock Rake RR1500 (22-September-2016) -64-...

  • Page 69: Adjustments

    6. Remove the clevis mounting pin. 7. Move the clevis up or down as required. 8. Install the clevis mounting pin and retainer. 9. Lower the hitch and check the pole angle again. 142274 - Rock Rake RR1500 (22-September-2016) -65-...
  • Page 70 5. To remove the center spring, loosen the nut on its eyebolt. Store the removed spring where it will be available when needed. 6. Readjust the remaining two springs to give the desired flotation. 142274 - Rock Rake RR1500 (22-September-2016) -66-...
  • Page 71 2. To adjust the tension, loosen the 1 x 3 1/2 in. sprocket bolt. Tighten the adjustment bolt to allow approximately 1/4” to 1/2” chain slack. Torque the 1” sprocket bolt to: 550 ft-lbs (745 N.m) 3. Replace the top access cover. 142274 - Rock Rake RR1500 (22-September-2016) -67-...
  • Page 72 (25-40mm) higher than the left end. By setting the right end of the drum higher than the left, soil will drop out of the rocks and not become part of the windrow. 142274 - Rock Rake RR1500 (22-September-2016) -68-...
  • Page 73 Reverse tooth and tighten mounting bolts. Be sure to install the tooth on the right hand side of the tooth holder. IMPORTANT: Torque all tooth bolts to 180 ft-lbs (245N.m). 142274 - Rock Rake RR1500 (22-September-2016) -69-...
  • Page 74 Tighten both bolts evenly until bushing dislodges. 6. Reposition the sprocket and secure by reinstall- ing the split bushing and tightening the three bolts evenly. Threaded Holes 142274 - Rock Rake RR1500 (22-September-2016) -70-...

  • Page 75: Repair

    3. Remove lock collar and bolts. 4. Pull bearing unit from shaft and replace. 5. Relocate lock collar and tighten in direction shown. 6. Tighten set screw. 7. Lubricate grease fitting. 142274 - Rock Rake RR1500 (22-September-2016) -71-...
  • Page 76 Using a sharp object such as a screwdriver, poke a hole into the seal and pry out. - Proceed to remove the snap ring, washer, and shim(s). (NOTE: Take care to remember the positioning of shaft shims.) 142274 - Rock Rake RR1500 (22-September-2016) -72-...
  • Page 77 (NOTE: If there is too much or too little backlash, fol- When proper set is achieved, apply sealant to bear- low the procedure for adjusting shims.) ing caps and tighten. 4. Install Seals 142274 - Rock Rake RR1500 (22-September-2016) -73-...
  • Page 78 7. Remove plastic removal ring from the cylinder internal tube groove tube. is fully exposed. This will also move the internal wire ring into its removal position. Inner Ring Outer Wire Ring Internal Groove (Removed) v1.0 142274 - Rock Rake RR1500 (18-April-2017) -74-...
  • Page 79 Note: Make sure the cam of the band clamp is c) Install External not overtop of the gap in the ring. Wire Ring Inner Ring External Ring 18. Before using the cylinder, ensure that you double check your work. 142274 - Rock Rake RR1500 (18-April-2017) -75-...
  • Page 80 6. Torque cylinder end cap to 440 lb.ft (600 N.m). end cap to align ports. 7. Tighten Set Screw on end cap to 6 lb.ft (8 N.m). 7. Tighten Locking Ring against end cap using a punch and hammer. 142274 - Rock Rake RR1500 (18-April-2017) -76-...
  • Page 81 9. Fill dust cap half full of grease and gently tap into position. 10. Pump grease into hub through grease fitting until lubricant can be seen from dust seal. Dust Spindle Seal Inner Cone Inner Outer Cotter Outer Cone Dust Washer 142274 - Rock Rake RR1500 (22-September-2016) -77-...
  • Page 82 12. Assemble the compression plate and all long bolts, making sure that all nuts are in their pockets. 9. Grease the fitting on the yoke using Shell Super Tighten all long bolts to 20 ft-lbs. Duty or an equivalent lithium grease. 142274 - Rock Rake RR1500 (18-April-2017) -78-...
  • Page 83 Resurface teeth (a double pass is recommended) using hard surface welding rods. A hardness of RC 45-50 is desirable. NOTE: Special hard surfacing rod kits are available through Degelman Industries Ltd. or your local Degelman Dealer. 142274 - Rock Rake RR1500 (22-September-2016)
  • Page 84 4. Clamp protruding bearing in vice. Tap yoke off bearing. 5. Turn joint over and tap exposed end of cross to remove second bearing. 6. Remove yoke. 142274 - Rock Rake RR1500 (22-September-2016) -80-...
  • Page 85 9. Tap bearing down to assemble second snap ring. 10. The joint should flex freely. If joint is stiff sharply strike yoke lugs as illustrated. 11. Reassemble protective shield and reinstall metal ring. 142274 - Rock Rake RR1500 (22-September-2016) -81-...

  • Page 86: Troubleshooting

    Rocks missed. Drum too light. Adjust suspension system to add weight to drum. (Remove 1 spring). (Page 66). Traveling too fast. Slow down. Rocks traveling too far. Drum turning too fast. Slow engine RPM. 142274 - Rock Rake RR1500 (22-September-2016) -82-...

  • Page 87: Specifications

    - Two 9.5L x 15 - 6 ply rating tubeless tires. - 3500 lbs (1580 kg) - 6 bolt rim. - 2 inch (51 mm) dia axles. SPECIFICATIONS AND DESIGN SUBJECT TO CHANGE WITHOUT NOTICE 142274 - Rock Rake RR1500 (22-September-2016) -83-...
  • Page 88 4. To prevent twisting the tube(s), use two 915 (1240) 1310 (1780) wrenches. Place one wrench on the connector 1250 (1695) 1785 (2420) body and with the second tighten the swivel nut 1600 (2175) 2290 (3110) to the torque shown. 142274 - Rock Rake RR1500 (22-September-2016) -84-...
  • Page 89 PUBLICATIONS Additional copies of the manual is available through your local dealer. If the dealer is unable Serial Number Plate to assist you, contact Degelman Industries Ltd. and order the part number below: 142274 Manual - RR1500 Serial Number...
  • Page 90 Plug, Port 1/2 NPT(M) - steel 128004 Weather Strip 5/16 x 3/4 in. Roll 305168 Pin Assembly 25.4 x 95mm (effective) 118848 Pin, Hair 5/32 in. 117087 Bushing, 1-1/4 OD x 1/8 W x 1 in. 142274 - Rock Rake RR1500 (22-September-2016) -86-...
  • Page 91 Nut, Lock 3/4 in. UNC, Gr5, Plated 118516 Washer, Flat 3/4 in. Plated 117087 Bushing, 1-1/4 OD x 1/8 W x 1 in. 117110 Bushing, 1-1/4 OD x 1/8 W x 3/4 in. 142274 - Rock Rake RR1500 (27-February-2019) -87-...
  • Page 92 Bolt, Hex 5/8 x 1-1/2 in. UNC, Gr5, Plated 118117 Bolt, Hex 5/8 x 5 in. UNC, Gr5, Plated 118508 Washer, Lock 5/8 in. Plated 118407 Nut, Hex 5/8 in. UNC, Gr5, Plated 118336 Grease Fitting 1/4 - 28 AMF self-tap 142274 - Rock Rake RR1500 (22-September-2016) -88-...
  • Page 93 Wheel Assembly 9.5L x 15 - 6 Ply 127003 Tire 9.5L x 15 - 6 Ply Tubeless 131001 Rim, Wheel 15 x 8 - 6 Bolt 127006 Valve Stem TR415 118336 Grease Fitting 1/4 - 28 AMF self-tap 142274 - Rock Rake RR1500 (22-September-2016) -89-...
  • Page 94 Hyd. Hose Clamp - 3/4 - 2 halves/set 305330 Top Plate, Hyd. Hose Clamp 3/4 118121 Bolt, Hex 5/16 x 2 in. UNC, Gr5, Plated 305335 Bolt Plate, 1/4 305328 Weld Plate, 3/4 Hyd Block 142274 - Rock Rake RR1500 (20-February-2020) -90-...
  • Page 95 Washer, Flat .905 OD x .591 ID x .079 in. 122800 Kit, Seal 3 in. Cylinder 1-1/4 in. Rod - DIL Seal, Piston - 3 in. - 5 part Seal, O-Ring Seal, O-Ring Seal, Wear Ring Seal, Rod Seal, Rod Wiper 142274 - Rock Rake RR1500 (22-September-2016) -91-...
  • Page 96 226597 - Key (1) 305325 - Sprocket, Drive 226598 - Seal Kit ) repair: #100 - 14 tooth (1) Note: Replaces Item 5 for municipal option. Complete Chain Tightener Assembly #305289 Items 13,36, 37,47,48,49, 50,51,52) 142274 - Rock Rake RR1500 (30-November-2018) -92-...
  • Page 97 Bolt, Hex 1/2 x 8 in. UNC, Gr5, Plated - Full Thread 118587 Washer, Flat 1/2 SAE Plated 118420 Nut, Lock 1/2 in. UNC, Gr5, Plated - Unitorque 118089 Bolt, Hex 1 x 3-1/2 in. UNC, Gr5, Plated 118510 Washer, Lock 1 in. Plated 142274 - Rock Rake RR1500 (22-September-2016) -93-...
  • Page 98 Vent, Pressure Relief 1/8 NPT(M) 119021 Reducer 1/8 NPT(F) x 1/2 NPT(M) 119448 Plug, Port 1/2 NPT(M) Allen Head 119447 Plug, Port 3/8 NPT(M) Allen Head 119439 Spacer, Tube 119446 Key 3/8 x 3/8 x 1.46 in. 142274 - Rock Rake RR1500 (22-September-2016) -94-...
  • Page 99 Bolt, Hex 3/8 x 3/4 in. UNC, Gr5, PL 119020 Vent, Pressure Relief 1/8 NPT(M) 119021 Reducer 1/8 NPT(F) x 1/2 NPT(M) 119448 Plug, Port 1/2 NPT(M) Allen Head 119447 Plug, Port 3/8 NPT(M) Allen Head 119439 Spacer, Tube 142274 - Rock Rake RR1500 (22-September-2016) -95-...
  • Page 100 Yoke 1 3/8 in. Q.D. - 6 Spline - Weasler - 540 PTO) 119880 Yoke 1 3/8 in. Q.D. - 21 Spline - Weasler - 1000 PTO 119357 Kit, Repair Safety Slide Lock - Q.D. 160206 Driveline Shield Guard Set - Inner & Outer 142274 - Rock Rake RR1500 (22-September-2016) -96-...
  • Page 101 119379 Plate, Compression - WSLR (#38-40075) 118783 Bolt, Hex 5/16 x 2-1/2 UNC GR8 PL 118427 Nut, Hex 5/16 UNC GR5 PL 119373 Non-Adjusting Friction Pack-9000 in. lb. (includes items 7 to 16) 142274 - Rock Rake RR1500 (22-September-2016) -97-...
  • Page 102 Kit, Repair Safety Slide Lock - Q.D. 118031 Bolt, 5/8 x 3 UNC GR8 (not included in above kits) 118447 Locknut, 5/8 UNC GRC (not included in above kits) 160223 Driveline Shield Guard Set - Inner & Outer 142274 - Rock Rake RR1500 (18-April-2017) -98-...
  • Page 103 Washer, Lock 3/8 in. Plated 118403 Nut, Hex 3/8 in. UNC, Gr5, Plated 118014 Bolt, Hex 1/2 x 2 in. UNC, Gr5, Plated 118504 Washer, Lock 1/2 in. Plated 118405 Nut, Hex 1/2 in. UNC, Gr5, Plated 142274 - Rock Rake RR1500 (22-September-2016) -99-...
  • Page 104 Washer, Flat 3/8 in. Plated 118503 Washer, Lock 3/8 in. Plated 118403 Nut, Hex 3/8 in. UNC, Gr5, Plated 118416 Nut, Jam 5/8 in. UNC, Gr2, Plated 118831 Pin, Hair 1/8 x 2 3/8 in. Plated 142274 - Rock Rake RR1500 (22-September-2016) -100-...
  • Page 105 118403 Nut, Hex 3/8 in. UNC, Gr5, Plated 118171 Bolt, Hex 1/2 x 7 1/2 in, UNC, Gr5, Plated 118504 Washer, Lock 1/2 in. Plated 118405 Nut, Hex 1/2 in. UNC, Gr5, Plated 142274 - Rock Rake RR1500 (22-September-2016) -101-...
  • Page 106 Bolt, Hex 3/4 x 2 1/2 in. UNC, Gr8, Plated 118509 Washer, Lock 3/4 in. Plated 118770 Nut, Hex 3/4 in. UNC, Gr8, Plated 118635 Washer, Flat 3/4 x 2 1/4 x 3/16 in. Plated 142274 - Rock Rake RR1500 (22-September-2016) -102-...

  • Page 107: Warranty

    Re-torque of fastening hardware, Hydraulic fluid purities, drive train alignments, and clutch operation) 3. If parts not made or supplied by Degelman have been used in the connection with the unit, if, in the sole judgement of Degelman such use affects its performance, safety, stability or reliability.
  • Page 108 Warranty Degelman Industries warrants this product to the original owner for a period of one (1) year parts and labour and two (2) years parts from the date of purchase. All matters related to the warranty of our products must be handled through the authorized selling dealer.
  • Page 109 142274 - Rock Rake RR1500 (22-September-2016) -105-...

Table of Contents