Download
Share
Print this page
  1. Manuals
  2. Brands
  3. CAME Manuals
  4. Door Opening System
  5. FLUO-SL
  6. Assembly and installation manual

CAME FLUO-SL Assembly And Installation Manual

Sliding door operator
Hide thumbs

Advertisement

Quick Links

Download this manual
SLIDING DOOR OPERATOR
F A 0 0 1 5 0 - E N
ASSEMBLY AND INSTALLATION MANUAL
FLUO-SL
EN
English

Advertisement

loading

Related Manuals for CAME FLUO-SL

Summary of Contents for CAME FLUO-SL

  • Page 1 SLIDING DOOR OPERATOR F A 0 0 1 5 0 - E N ASSEMBLY AND INSTALLATION MANUAL FLUO-SL English...

  • Page 2: General Safety Instruction

    Make sure the existing structure is up to standard in terms of strength and stability. CAME S.p.A. is not responsible for failure to use Good Working Methods in building the frames to be motorised or for any deformation occurring during use.

  • Page 4: Technical Data

    The installer must adopt adequate safety coefficients for each particular installation. FA00150-EN v.7 - 06/2017 CAME S.p.A.

  • Page 5: Standard Installation

    Note: Components and codes are those most commonly used in systems for automatic sliding doors. The full range of equipment and accessories is also available in the sales list. The given operating and performance features can only be guaranteed with use of CAME S.p.A. accessories and safety devices.
  • Page 6 To facilitate the calculations and the choice for the ordination of automatic sliding doors, CAME S.p.A. has developed the CAME DoorConfigurator computer program.
  • Page 7 2235 mm 5600 mm 001FL1S66 6600 mm 3225 mm 3315 mm 60 mm 2875 mm 3035 mm 7200 mm (N.B. Values shown are calculated considering Loo = 50 mm and Loc = 40 mm) FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 8 2405 mm 5940 mm 001FL1S66 6600 mm 3225 mm 3315 mm 60 mm 2705 mm 3205 mm 7540 mm (N.B. Values shown are calculated considering Loo = 50 mm and Loc = 40 mm) FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 9 4.4 PROFILES AND GASKET CUTTING MEASURE All the aluminium profiles and gaskets needed for the realization of the FLUO-SL automations must be cut 20 mm shorter than the maximum length of the automation (Ld – 20), also including the plastic end caps.
  • Page 10 4.5 VERTICAL DOOR DIMENSION The FLUO-SL automations are compatible with the majority of frame in trade. The formulas are for the calculation of the vertical measure fastening automations (Hd), and for the calculation of the height of sliding door (Hm).
  • Page 11 5. ASSEMBLY PROCEDURE OF THE AUTOMATION The FLUO-SL automations should be assembled by qualified personnel, and can be done at the factory or directly at the place of installation of the door. After size cutting all aluminium profiles and gaskets (as indicated in the chapter 4.4), we proceed with the automation and internal components assembly.
  • Page 12 5.7 Insert the belt in the pulley motor drive unit, slide it and pass it around the transmission unit and fix to carriage with the proper springs (see the belt attack position, as shown in Chapter 4). FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 13 Note: To avoid that the cover can be opened without the use of a tool, it is necessary to make two 5 mm holes in diameter at the ends of the cover profile [102], as shown in the figure, and fix the cover with the screws 4,8 x13 in provided (Note: use the screw located near the magnet). FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 14 The automations FLUO-SL are compatible with the majority of frame systems in trade. Fixing of the support profile [FLUO-SL], or the drive unit profile [FLUO-SLB], to the wall must be safe and suitable for the weight of the doors. Distribute the fixing points every 500 to 800 mm (or 300÷500 mm for SL5H, SL5B) along the...
  • Page 15 Make sure that the bottom of the doors is properly guided by the floor runner. Adjust the position of the brackets with a mechanical stop to limit the travel of the doors in the desired locations. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 16 - Rescrew the 4 lower screws [a] of the lock. Note: pulling the unlock rope the doors are unlocked, also in the absence of electricity, and remain unlocked until is not restored electrical operation. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 17 - Check the operation of the magnetic coupling and uncoupling of the sensor support, even in the presence of the cover automation. - Connect the sensors to the electronic control, as shown in Chapter 12. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 18 Note: to make sure that the door is closed and locked, connect to the signalling device in combination to the signalling device door position [001FLA-06]. FA00150-EN v.7 - 06/2017 CAME S.p.A.

  • Page 19: Electrical Connections

    Angular sensor 001FLA-01 Battery power device (001FLA-02 code for Emergency exit) FUSE F2 Battery fuse 5x20 - F16A 001FLA-03 Locking device 001FLA-04 Signaling lock position device (connected to terminals 1-S1 in Emergency exit automation) FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 20 During installation, maintenance and repair operations, cut off the power supply before opening the cover to access the electrical parts. To handle electronic parts, wear earthed antistatic conductive bracelets. CAME S.p.A. declines all responsibility in the event of components which are not compatible with the safe and correct operation of the product.
  • Page 21 Open the door. ↑ Scroll the menu and increase of selected values. ↓ Scroll the menu and reduction of selected values. ENTER Button to select the menu and save the selected data. Exit the menu. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 22 Information symbol flashing = shows the presence of alarms: - 1 flash = failure of electronic control or locking device; - 2 flashes = mechanical failure; - 3 flashes = failure of sensor safety test; - 4 flashes = motor overtemperature. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 23 Connect the sensor, using the supplied cable to the terminals of the electronic control as follows: CB01 001MR8204 sensor Notes Brown Green Yellow 3A (3B) White Blue Pink 8A (8B) Gray Remove the jumper For more information, check the installation manual of the sensor. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 24 Do not connect Connect the sensor B side, using the supplied cable to the terminals of the electronic control as indicated in Section 12.5. For more information, check the installation manual of the sensors. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 25 Connect the sensor, using the supplied cable to the terminals of the electronic control as follows: CB01 001MR8701 sensor Notes Brown Blue Green Pink 6A (6B) Gray Remove the jumper Yellow Do not connect White Do not connect For more information, check the installation manual of the sensor. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 26 Connect the photocell, using the cables supplied to the terminals of electronic control as follows: Terminals PE12CNT15 emitter (grey cable) PE12CNT15PO receiver (black cable) Notes Blue (BU-) Blue (BU-) Brown (BN+) Brown (BN+) Remove the jumper. 8A (8B) Black (BK) Set the menu: ADV > T41 > NO. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 27 = terminal 0 red wire = terminal 1 white wire = terminal 1 white wire = terminal KO For more information, refer to the installation manual of the transponder reader. FA00150-EN v.7 - 06/2017 CAME S.p.A.

  • Page 28: Main Settings Menu

    NO = the door is always open TIME minimum value = 1 s maximum value = 30 s PUSH Force setting. Choose between the minimum and maximum: MOTOR minimum value = 1 POWER maximum value = 10 FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 29 You can save the menu settings of automation in use, in the micro SD memory. Choose between the SETTING following values: OUTPUT NO = no save YES = save the menu settings of automation in the micro SD memory FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 30 Choose between the following values: CIRCUIT OC = manual door opening without friction (motor with open circuit windings) SC = manual door opening with friction (motor with short-circuit windings) FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 31 CAB = (see menu: ADV > STG1 > CAB) Enable test for safety devices (in accordance with EN 16005). Choose between the following values: SAFETY TEST NO = test disabled YES = test enable FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 32 - approach the badge to the function selector (in front of the NFC symbol), the display shows the badge code, - wait for 20 seconds or press the ESC button. Note: if the badge and the numeric code is not recognized the display shows the message UNKN. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 33 EMERGENCY - In case of Emergency automation, the "closed door" setting must be made only by the function selector. 1D = automatic one-way operation PA = automatic partial operation 1DPA = automatic one-way operation and partial FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 34 Displaying of the last 10 warnings (the warning number 0 is the last): 0. - - - WARNING 0.xxx / 1.xxx / 2.xxx / 3.xxx / 4.xxx / 5.xxx / 6.xxx / 7.xxx / 8.xxx / 9.xxx LIST FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 35 Door locked closed Check the presence of locks W256 Power on W257 Firmware update W320 Signaling of maintenance Check the INFO > SERV menu W330 Tuning between motor and electronics Wait about 3-30 seconds FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 36 14.8 At the end of the automation starting, deliver to the owner the user instructions, including all warnings and information necessary to maintain the security and functionality of the automatic door. 14.9 FLUO-SL automations are feature of label on the right end cap, containing the required information by European standards EN16005 and EN60335-2-103.
  • Page 37 15.13 FLUO-SL automations are feature of label on the right end cap, containing the required information by European standards EN16005 and EN60335-2-103. Note: the manufacturer of the automatic sliding door have to add his own label identifying the installation.

  • Page 38: Troubleshooting

    Check the adjustment of the position of the carriage, will not release brackets coupling lock. Pulling the release cord don’t unlock the Check the correct fitting of the release cord on doors. the lock. FA00150-EN v.7 - 06/2017 CAME S.p.A.

  • Page 39: Disposal Of Products

    For repairs or replacements of products, original spare parts must be used. 17.1 DISPOSAL OF PRODUCTS For correct disposal of electrical and electronic equipment, batteries and accumulators, the owner must deliver the product to special "collection centres" provided by municipalities. FA00150-EN v.7 - 06/2017 CAME S.p.A.
  • Page 40 Came S.p.A. Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c s a f e t y & c o m f o r t 31030 Dosson di Casier Dosson di Casier 33079 Sesto al Reghena Sesto al Reghena...