CAME FLUO-SW Assembly And Installation Manual
  1. Manuals
  2. Brands
  3. CAME Manuals
  4. Door Opening System
  5. FLUO-SW
  6. Assembly and installation manual

CAME FLUO-SW Assembly And Installation Manual

Swing door operator
Hide thumbs

Advertisement

Table of Contents

SWING DOOR OPERATOR
F A0 0 0 0 8 - E N
ASSEMBLY AND INSTALLATION MANUAL
FLUO-SW
EN
English

Advertisement

Table of Contents
loading

Related Manuals for CAME FLUO-SW

Summary of Contents for CAME FLUO-SW

  • Page 1 SWING DOOR OPERATOR F A0 0 0 0 8 - E N ASSEMBLY AND INSTALLATION MANUAL FLUO-SW English...

  • Page 2: General Safety Instruction

    Make sure the existing structure is up to standard in terms of strength and stability. CAME S.p.A. is not responsible for failure to use Good Working Methods in building the frames to be motorised or for any deformation occurring during use.

  • Page 4: Technical Data

    The installer must to adopt adequate safety coefficients for each particular installation. FA00008-EN v.7 – 05/2017 CAME S.p.A.

  • Page 5: Standard Installation

    Note: Components and codes are those most commonly used in systems for automatic swing doors. The full range of equipment and accessories is also available in the sales list. The given operating and performance features can only be guaranteed with use of CAME S.p.A. accessories and safety devices.
  • Page 6 Adjust the opening mechanical stop inside the sliding arm. CLOSING OF THE AUTOMATION COVER Fix the cover to the heads at the lower holes (or at the lateral holes), using the screws 2,9 x9,5 not supplied by us. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 7 Note: the mechanical stop on the floor must be fixed in a visible position and must not create tripping hazard. CLOSING OF THE AUTOMATION COVER Fix the cover to the heads at the lower holes (or at the lateral holes), using the screws 2,9 x9,5 not supplied by us. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 8 If the door has the hinge on the right, disassemble the gear motor group from the automation and move the spring group from the left side to the right side of the automation, as shown in the figure. Factory setting Hinge on the right FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 9 Attach the cover profile to the base profile. To prevent the cover from being opened without the use of a tool, you can secure the cover to the heads at the holes, using the screws 2,9 x9,5 not supplied by us. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 10 Note: if necessary, you can change the measure H, between the automation and the door, by replacing the spacer, using the codes listed in the table. PBBS2 automation 001PBBA02 + 001PBBA06 001PBBA02 001PBBA02 + 001PBBA08 FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 11 Attach the cover profile to the base profile. To prevent the cover from being opened without the use of a tool, you can secure the cover to the heads at the holes, using the screws 2,9 x9,5 not supplied by us. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 12 Attach the cover profile to the base profile. To prevent the cover from being opened without the use of a tool, you can secure the cover to the heads at the holes, using the screws 2,9 x9,5 not supplied by us. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 13 Attach the cover profile to the base profile. To prevent the cover from being opened without the use of a tool, you can secure the cover to the heads at the holes, using the screws 2,9 x9,5 not supplied by us. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 14 If desired, you can connect a N.O. contact to reactivate the battery operation (example a key switch, not supplied) between the terminals [+] and [KY ] as shown in Figure. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 15 In case the electromagnet used requires a stabilized power supply of 12 Vdc (with absorption of 500 mA max), use the KITL relay card and make the connections shown in the figure. - Set from menu: ADV > ELLK > SAVE or AUTO. - Set from menu: ADV > LKPW > 12. FA00008-EN v.7 – 05/2017 CAME S.p.A.

  • Page 16: Electrical Connections

    During installation, maintenance and repair operations, cut off the power supply before opening the cover to access the electrical parts. To handle electronic parts, wear earthed antistatic conductive bracelets. CAME S.p.A. declines all responsibility in the event of components which are not compatible with the safe and correct operation of the product.
  • Page 17 Open the door. ↑ Scroll the menu and increase of selected values. ↓ Scroll the menu and reduction of selected values. ENTER Button to select the menu and save the selected data. Exit the menu. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 18 Information symbol flashing = shows the presence of alarms (as described in chapter 13.5): - 1 flash = failure of electronic control or locking device; - 2 flashes = mechanical failure; - 3 flashes = failure of sensor safety test; - 4 flashes = motor overtemperature. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 19 = terminal 0 brown wire = terminal 1 yellow wire = terminal 1 green wire = terminal 3A or 3B For more information, check the installation manual of the sensor. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 20 = 8A terminal (remove the jumper 41-8A) red wire = terminal 41 yellow wire = do not connect white wire = do not connect gray wire = do not connect black wire = do not connect FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 21 Connect the opening sensors as described in chapter 7.5 and connect the safety sensors as described in chapter 6.6. If desired, connect the function selector, as shown in the figure. Note: the partial opening of only one leaf is referred to the MASTER automation. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 22 = terminal 0 red wire = terminal 1 white wire = terminal 1 white wire = terminal 3A, or terminal 3B For more information, refer to the installation manual of the transponder reader. FA00008-EN v.7 – 05/2017 CAME S.p.A.

  • Page 23: Basic Settings Menu

    CONT = continuation of normal operation of the door, with last cycle of opening Note: the number of operations with battery, depends on the efficiency of the battery, the weight of the doors and the present friction. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 24 AUTO = anti-panic electric lock (operation matched to the function selector) LKPW Power supply electric lock. Choose between the following values: LOCK POWER 12 = 12V electric lock SUPPLY 24 = 24V electric lock FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 25 Setting the manual friction of the door, by means of the electrical connection of the motor windings. MOTOR Choose between the following values: CIRCUIT OC = manual door opening without friction (motor with open circuit windings) SC = manual door opening with friction (motor with short-circuit windings) FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 26 CAB = (see menu: ADV > STG2 > CAB) Enable test for safety devices (in accordance with EN 16005). Choose between the following values: SAFETY TEST NO = test disabled YES = test enable FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 27 - approach the badge to the function selector (in front of the NFC symbol), the display shows the badge code, - wait for 20 seconds or press the ESC button. Note: if the badge and the numeric code is not recognized the display shows the message UNKN. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 28 Connect the contact of a clock to 1-G1 (1-G2) terminals, and choose between the following values: MODE OPEN = open door AUTO = automatic bi-directional operation CLOS = closed door 1D = automatic one-way operation FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 29 Displaying of the last 10 warnings (the warning number 0 is the last): 0. - - - WARNING 0.xxx / 1.xxx / 2.xxx / 3.xxx / 4.xxx / 5.xxx / 6.xxx / 7.xxx / 8.xxx / 9.xxx LIST FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 30 Synchronization error Check the ADV > SYNC menu W256 Power on W257 Firmware update W320 Signaling of maintenance Check the INFO > SERV menu W330 Tuning between motor and electronics Wait about 3-30 seconds FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 31 9.9 FLUO-SW automations are feature of label containing the required information by European standards EN16005 and EN60335-2-103. Note: the manufacturer of the automatic swing door have to add his own label identifying the installation.

  • Page 32: Troubleshooting

    The opening and safety devices are Verify that the opening sensors are not subject itself. unstable or detect moving bodies to vibration , do not perform false detections or the presence of moving bodies in the field of action. FA00008-EN v.7 – 05/2017 CAME S.p.A.

  • Page 33: Disposal Of Products

    For repairs or replacements of products, original spare parts must be used. 12.1 DISPOSAL OF PRODUCTS For correct disposal of electrical and electronic equipment, batteries and accumulators, the owner must deliver the product to special "collection centres" provided by municipalities. FA00008-EN v.7 – 05/2017 CAME S.p.A.
  • Page 34 Came S.p.A. Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c s a f e t y & c o m f o r t 31030 Dosson di Casier Dosson di Casier 33079 Sesto al Reghena Sesto al Reghena...

Table of Contents