Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech EPD-130
Summary of Contents for Advantech EPD-130
- Page 1 User Manual EPD Control Board EPD-130 ePaper Display Solution...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
- Page 4 FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES) Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all Wi-Fi product marketed in US must fixed to US operation channels only. EPD-130 User Manual...
- Page 5 XXXyyyLPDzzzz-x」 字樣。 Technical Support and Assistance Visit the Advantech website at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
- Page 6 Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. 1 pcs EPD-130 EPD control board & 1 pcs 13.3" EPD Ordering Information Part No. Description EPD-130B1AG-NSD01 13.3 "...
- Page 7 The equipment has been dropped and damaged. The equipment has obvious signs of breakage. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. EPD-130 User Manual...
- Page 8 Equipment L'équipement est tombé et a été endommagé. Equipment L'équipement présente des signes évidents de rupture. AVERTISSEMENT: Cet ensemble d'instructions est donné conformément à la norme CEI 704-1. Advantech décline toute responsabilité quant à l'exactitude des déclara- tions contenues dans le EPD-130 User Manual viii...
-
Page 9: Table Of Contents
Introduction ....................2 Specifications .................... 2 Figure 1.1 Block Diagram ............3 System Implementation................3 1.3.1 Advantech EPD-130 Wired Connection to Customer Host... 3 Chapter EPD Hardware Specifications ....5 Figure 2.1 MODULE OUTLINE: 108 x 122 x 3.9 mm ....6 Figure 2.2 Module Connection to Panel Specifications .... - Page 10 4.3.2 Repair Process ................30 EPD-130 User Manual...
-
Page 11: Chapter 1 Introduction
Chapter Introduction... -
Page 12: Introduction
Introduction Advantech EPD-130 provides Micro USB & SPI pin headers to connect to the host computer. The user's host computer can control the ePapaer display through the EPD-130. The module can support hospital, factory, warehouse and retail applica- tions with optimization for power consumption. Indeed, system integrators and end users can focus on application development and system management. -
Page 13: System Implementation
In some scenarios, customers would like to use their own host computer to control ePaper directly, so they can use EPD-130 which provides Micro USB & SPI pin head- ers to connect to the host computer. In this user scenario, EPD-130 is in the slave role to be controlled by the developer's host. - Page 14 EPD-130 User Manual...
-
Page 15: Chapter 2 Epd Hardware Specifications
Chapter EPD Hardware Specifications... - Page 16 PN: 968AD00388 Operation temperature range: 0 °C to +50 °C for Black and White, PN:968AD00147 Operation temperature range: 0 °C to +40 °C for Red, Black and White. All E Ink Panel inspection criteria refers to E Ink CAS & Inspection standard doc- ument. EPD-130 User Manual...
- Page 17 Temperature: 20 +-10 °C Humidity: 60% RH+-10%RH, Non-condensing Note! If panel module have been put in low temperature between 0~-25 °C for a while, we recommend to leave it between 20 to 30 °C for 4 days before assembly. EPD-130 User Manual...
-
Page 18: Board Level I/O
39 pins FPC to connect to e-paper panel ALERT 10 pins FFC to connect to daughter board FFC_GPIO 10 pins FFC connector for external GPIO DEBUG 10 pins FFC connector SWTEST For software test PWR_ON1 4 pins DIP Switch EPD-130 User Manual... -
Page 19: Cn2
2.1.1 Table 2.2: CN2 PIN_NAME USB_D- USB_D+ EPD-130 User Manual... -
Page 20: Cn3
2.1.2 Table 2.3: CN3 PIN_NAME EPD-130 User Manual... -
Page 21: Cn8
2.1.3 Table 2.4: CN8 (SPI PIN HEADER) PIN_NAME PIN_NAME SPI_CLK (Serial Clock) SPI_MOSI (Master Output,Slave Input) SPI_MISO (Master Input,Slave Output) SPI_CS0# (Slave Selected) Serial Clock: SCLK: SCK Master Output → Slave Input (MOSI): EPD-130 User Manual... -
Page 22: Cn9
MISO (or SDI on a master) connects to MISO (or SDO on a slave). Slave Select is the same functionality as chip select and is used instead of an addressing concept. Pin names are always capitalized as in Slave Select, Serial Clock, and Master Output Slave Input. 2.1.4 EPD-130 User Manual... -
Page 23: Epd Connector
Table 2.5: CN9 PIN_NAME PIN_NAME 2.1.5 EPD Connector EPD-130 User Manual... - Page 24 SDDO6 (Data) SDDO7 (Data) +VCOM (Common connection) +VGH (Positive power supply +VGL (Negative power supply gate driver) gate driver) GDOE_P (Output mode selec- tion gate driver) SPV (Start pulse gate driver) GDCLK (Clock gate driver) +VCOM (Common connection) EPD-130 User Manual...
-
Page 25: Ffc_Gpio
2.1.6 FFC_GPIO Table 2.7: FFC_GPIO PIN_NAME PIN_NAME +V3.3 GPIO_0 (default LOW) GPIO_1 (default LOW) GPIO_2 (default LOW) GPIO_3 (default LOW) GPIO_4 (default LOW) GPIO_5 (default LOW) GPIO_6 (default LOW) GPIO_7 (default LOW) GPIO Voltage level is 3.3V EPD-130 User Manual... -
Page 26: Debug
2.1.7 DEBUG Table 2.8: DEBUG PIN_NAME PIN_NAME UART1_TX UART1_RX JTAG_TDI JTAG_TDO JTAG_TCK JTAG_TMS JTAG_TRST EPD-130 User Manual... -
Page 27: Swtest
Table 2.8: DEBUG BOOT_0 +V3.3_DEBUG 1. TDI (Test Data In) 2. TDO (Test Data Out) 3. TCK (Test Clock) 4. TMS (Test Mode Select) 5. TRST (Test Reset) optional. 2.1.8 SWTEST Table 2.9: SWTEST PIN_NAME PIN_NAME SW_TEST# SW_TEST# EPD-130 User Manual... -
Page 28: Pwr_On1
2.1.9 PWR_ON1 Table 2.10: PWR_ON1 PIN_NAME PIN_NAME NC: only for SW testing usage NC: only for SW testing usage EVK_MODE# W_DISABLE: WiFi power on/off BM22 mode EVK mode WIFI power ON WIFI power OFF EPD-130 User Manual... -
Page 29: Panel, Pcba Connector And Usb Data Transmission Connector
Users can see the below FPC from the ePaper display Release rotary latch of the connector on the control board Blend the FPC carefully to the control board direction Insert the FPC into the connector on control board EPD-130 User Manual... - Page 30 After connecting steadily, lock the rotary latch Check if the connection is correct and tight. Item2 in below figure: Connected Wi-Fi antenna to mainboard Item6 in below figure : Connected power cable to mainboard USB(CN2) EPD-130 User Manual...
-
Page 31: Chapter 3 Epd Software Development
Chapter EPD Software Development... -
Page 32: Components List
Components List 3.1.1 HW Components List Item Description Quantity 13.3" ePaper display EPD-130 controller (PCBA) USB cable Host computer 3.1.2 SW Components List Item Description Quantity EPD-132R_CLItool to send out the image from host computer System Architecture Tool And Development Environment Setup Download and unzip EPD-132R_CLItool Click "IT8951_FWVersion.bat"... -
Page 33: Evaluation Kit Hands-On
Evaluation Kit Hands-On Follow steps and picture below to setup the hardware Connect EPD FPC to mainboard Connect USB cable to mainboard USB2(CN2) EPD-130 User Manual... - Page 34 Download and Refresh Image Click "IT8951_UpdateImage1.bat" to update "13.3inch-01.bmp" to EPD. Click "IT8951_UpdateImage2.bat" to update "13.3inch-02.bmp" to EPD. Open "IT8951_UpdateImage1.bat" and edit "13.3inch-02.bmp" for your image name. *The image will not saved in flash EPD-130 User Manual...
-
Page 35: Chapter 4 Wise-Ec Epd Design-In Service
Chapter WISE-EC EPD Design- In Service... -
Page 36: The Acquisition Of Information
The Acquisition of Information Since ePaper is not a plug and play device, Advantech WISE-EC Design-in Services help customers reduce the time and work involved with designing a new ePaper device. Advantech handles the complexities of technical research and provides hard-... -
Page 37: Design
TX power / mask / RF harmonic tuning / RX sensitivity When a product moves into the design stage, Advantech will supply a design guide of the EPD device for reference as well as Antenna selection & schematic review. The... -
Page 38: Integration
Therefore the customer has to learn from trial and error and to get the best solution with the least effort. Advantech's team has completed total standard HW/SW solutions to do performance fine tuning, driver inte- gration and application-specific customization. -
Page 39: Contact Information
Warranty Period Advantech branded off-the-shelf products and 3rd party off-the-shelf products used to assemble Advantech Configure to Order products are entitled to a 2 year complete and prompt global warranty service. Product defects in design, materials, and work- manship, are covered from the date of shipment. - Page 40 (Dead-on-Arrival). The DOA Cross-Shipment excludes any shipping damage, cus- tomized and/or build-to-order products. For those products which are not DOA, the return fee to an authorized ADVANTECH repair facility will be at the customers' expense. The shipping fee for reconstructive products from ADVANTECH back to customers' sites will be at ADVANTECH's expense.
- Page 41 "Attn. RMA Service Department". All products must be returned in properly packed ESD material or anti-static bags. ADVANTECH reserves the right to return non-repaired items at the customer's cost if inappropriately packed. Besides that, "Door-to-Door" transportation such as speed post is recommended for delivery, otherwise, the sender should bear additional charges such as clearance fees if Air-Cargo is adopted.
- Page 42 If a product has been repaired by ADVANTECH, and within three months after such a repair the product requires another repair for the same problem, ADVANTECH will do this repair free of charge. However, such free repairs do not apply to products which have been misused, abused, or subjected to unauthorized disassembly/modification;...
- Page 43 EPD-130 User Manual...
- Page 44 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2019...