ZOLL M Series Manual
  1. Manuals
  2. Brands
  3. ZOLL Manuals
  4. Medical Equipment
  5. M Series
  6. Manual

ZOLL M Series Manual

12-lead ecg monitoring
Hide thumbs Also See for M Series:
Table of Contents

Advertisement

Quick Links

12-Lead ECG Monitoring
9650-0215-01 Rev. H

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ZOLL M Series

Summary of Contents for ZOLL M Series

  • Page 1 12-Lead ECG Monitoring 9650-0215-01 Rev. H...
  • Page 2 This issue date or revision level for this operation guide is shown on the front cover. ZOLL and M Series are trademarks of ZOLL Medical Corporation. © 2002 by ZOLL Medical Corporation. All rights reserved...

  • Page 3: General Information

    How to Use This Manual This manual provides instructions for using the ZOLL M Series with 12-Lead option. It does not contain information on how to read or interpret electrocardiograms (ECGs). It covers the following: •...
  • Page 4 Before use, carefully read the M Series Operator’s Guide and these operating instructions. • The M Series with 12SL is designed to acquire and interpret ECG data from resting, supine patients. Use of the device to acquire ECG signals from moving or shaking patients may produce erroneous 12-lead interpretation results. Always ensure that the patient is kept motionless during 12-lead ECG signal acquisition and analyses.

  • Page 5: Electrode Placement

    When acquiring 12-lead ECG from quiet supine patients, lateral to and just below the Angle of Louis. ZOLL recommends placing the limb electrodes anywhere Move your finger down two more intercostal spaces to along the ankles and wrists. When it is difficult for the patient the fourth intercostal space which is the V1 position.
  • Page 6 V-lead connector.) when the electrodes are attached to the patient. • Attach the 12-lead cable to the rear of the M Series product. Pressing the Acquire softkey causes the M Series to begin sequencing through the necessary steps to produce a •...
  • Page 7 Transmission Error In the event of a failure to transmit the ECG record, the operator will be notified and the M Series will continue to retry the transmission until the operator aborts the transmission or the transmission is successful. See “Troubleshooting” for possible transmission error messages and corrective actions.
  • Page 8 12SL algorithm performs a pediatric M Series screen. For example, if Lead II is displayed, leads I, II analysis. and III will be printed; if lead V3 is displayed, leads V1, V2, and V3 will be printed.
  • Page 9 Return softkey to return to the Patient Information Menu and store the name and ID number. If no patient ID # is entered the M Series automatically generates a 12 digit patient ID# based on the year/date/time (200002151320) of the first 12-lead acquisition.
  • Page 10 Cabrera print formats. 1 mV calibration pulses are printed at the beginning of the report for each data channel. You can also configure the M Series unit to print 5, 7.5, or 10 seconds of ECG data for each set of leads. If you specify a setting of 5, 7.5, or 10 seconds, the M Series unit prints data for the same time period (5, 7.5, or 10 seconds) for each set of ECG leads;...
  • Page 11 12-lead 4x3 Median Complexes This format prints a single median beat for each of the twelve (12) leads. The median beat is computed by the 12SL algorithm and is denoted by a squiggle at the end of each median lead. The report can be configured for either standard or Cabrera print formats. 1 mV calibration pulses are printed at the beginning of the report for each data channel.

  • Page 12: Patient Information

    The unit can be configured to print out a measurements matrix, which consists of measurements for each segment of each lead. To print the measurements matrix at the end of an analysis, the user must change the default setting in the M Series device (see the M Series Configuration Guide, P/N 9650-0201-01, for more details).
  • Page 13 ECG recording by the 12SL program. For interpretation of these results refer to the 12SL Measurements: Measurements are displayed based on all ECG Analysis Program Physicians Guide (ZOLL P/N 12-leads. 3001-0203). The global measurements include heart rate, PR Interval, QRS duration, QT &...
  • Page 14 Cycle through each of the 12 leads by pressing the LEAD button. Verify that good quality, artifact-free ECG signals are displayed and stabilized within 10 seconds on your M Series. Verify the ECG LEAD OFF message is NOT displayed on the screen.

  • Page 15: Troubleshooting

    The troubleshooting guide is intended to help you identify and correct problems that arise during operation. If trouble persists after consulting this guide, contact the ZOLL Technical Service Department for problems relating to the M Series unit or GE Medical Systems Information for problems relating to the Catalyst MUSE system.
  • Page 16 Check the M Series configuration for valid Catalyst MUSE site and location identifiers. Receiving phone line is being used. The M Series automatically 5. “FAX BUSY” or re-transmits until the transmission is successful or the M Series “MUSE BUSY”...
  • Page 17 An overriding activity, such as an alarm situation, preempted data 13. “MUSE DATA NOT VALID” in the process of being saved to the M Series unit. The data is message is displayed. incomplete or corrupted. Re-acquire 12-lead data and re-transmit.
  • Page 18 Modem • When included, the M Series with 12-Lead option ships with a cellular-ready PC card modem installed in the upper PCMCIA slot (domestic units only). • The M Series with 12-Lead option is also available with an approved GSM card modem (obtained locally for international customers).
  • Page 19 The connectors are keyed and only mate in one orientation. Configuring Phone Numbers • Please see the ZOLL M Series Configuration Guide, P/N 9650-0201-01, for instructions on how to program automatic-dial phone numbers into the M Series unit. •...

  • Page 20: Fcc Regulations

    • The modem card is a non-serviceable/repairable item. It is the responsibility of the user to report the need for any service to the device to ZOLL Medical Corporation. • If you encounter any problems with your telephone after installing any new device, disconnect it from the telephone line to see if the device is the source of the problem.

  • Page 21: Shielded Cables

    If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, please contact ZOLL Medical Corporation, for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is NOT malfunctioning.

  • Page 22: Canadian Requirements

    OPTION INSERT Canadian Requirements The Industry Canada, formerly the Canadian Department of Communications, label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction.
  • Page 23 Configure the Catalyst MUSE system to forward ECGs to physicians or devices such as carts or fax machines Ask the person responsible for configuring the M Series unit to set up the telephone numbers and the MUSE site and location identifiers that the Catalyst MUSE system administrator provided. It is recommended that the M Series device identifier also be configured.

Table of Contents