Siemens SIMATIC ET 200X Manual page 358

Index
EM 148-P DO 16 x P/CPV10, features, 7-74
EM 148-P DO 16 x P/CPV10 expansion
module
basic circuit diagram, 7-74
technical specifications, 7-75
EM 148-P DO 16 x P/CPV14, features, 7-76
EM 148-P DO 16 x P/CPV14 expansion
module
basic circuit diagram, 7-76
features, 7-76
technical specifications, 7-77
EMC, 4-31, 4-32, 6-4
EMERGENCY STOP devices, 4-2
Emission of radio interference, 6-5
Equipotential bonding, Glossary-3
Error handling, Glossary-3
ET 200X
commissioning, 5-7
features, 1-6
installing, 3-6
installing on DIN rail, 3-6
range of modules, 1-5
wired, 4-36
wiring, 4-11
Expansion module, 1-5
number per ET 200X, 2-13, 2-16
Expansion module EM 141 DI 4 x DC 24V,
pinout, digital inputs, 7-34
Expansion module EM 141 DI 8 x DC 24V,
pinout, digital inputs, 7-44
Expansion module EM 141 DI 8 x DC 24V
(6ES7 141-1BF30-0XA0), pinout, digital
inputs, 7-37
Expansion module EM 141 DI 8 x DC 24V
(6ES7 141-1BF40-0XA0), pinout, digital
inputs, 7-44
Expansion module EM 141 DI 8 x DC 24V
(6ES7 141-1BF40-0XB0), pinout, digital
inputs, 7-41, 7-48
Expansion module EM 141 DI 8 x DC 24V
DIAG, pinout, digital inputs, 7-40, 7-47
Expansion module EM 142 DO 4 x DC
24V/0.5A, pinout, digital outputs, 7-51
Expansion module EM 142 DO 4 x DC 24V/2A,
pinout, digital outputs, 7-54
Expansion module EM 148-P DO 16 x
P/CPV10, features, 7-74
Extended diagnosis, 5-27
External power supply, Glossary-3
Index-4
F
FB 192 "IM308C", 5-31
FB 230, 5-29
Features
of ET 200X, 1-6
of ET 200X-DESINA, 1-8
Four-wire measuring transducer, 7-106
connection, 7-108
FREEZE, Glossary-4
Frequency converter, Glossary-4
number per ET 200X, 2-13
Frequency converters, 1-6
G
General technical specifications, 6-1
Ground, Glossary-4
Grounded supply, 4-4
Grounding, 4-1
analog modules, 4-32
Guide, through the manual, iv
H
Hardware interrupt, triggering, 5-26
I
I/O device, distributed, 1-2
ID-specific diagnosis, 5-37
Identification code for Australia, 6-2
IEC 61131, 6-2
Important information, iii
Install, pneumatic-interface module, 3-14
Installation, 3-1
sequence, 3-1
SITOP power, 3-7
valve island, 3-13
Installation position, of the ET 200X, 3-2
Installing
ET 200X, 3-6
pneumatic components, 3-11
Insulation testing, 6-9
Integrating the DDB file in the configuration
software, 5-9
Interrupts, 5-24, 5-43
from station diagnosis, 5-53
ET 200X Distributed I/O Device
EWA 4NEB 780601602-06