FUEL SYSTEM DRAIN SYSTEM WIRING DIAGRAM PREPARATION FOR EXPLOITATION INFLATION/DEFLATION BOAT TUBE STORAGE BATTERY INSTALLATION BOAT TRANSPORTATION BY TRAILER HOW TO INSTALL SUNDECK CREW LIMIT REBOARDING MEANS ANCHORING AND TOWING.Strong points. MOORING.Strong points. MAINTENANCE OPERATING REGULATIONS 2019 — 2 — BRIG...
Page 3
CHECK, THAT THE CHECKS HAVE BEEN MADE AND THAT THE PLANTS HAVE BEEN COMPLETED BEFORE DELYVERY. BRIG Ltd declines any responsibility for systems and accessories that have not been installed and checked by expert and authorised personnel. The manual and all its enclosures should be stored carefully, and the manual should always be kept aboard.
Page 4
Recreational Craft Directive 2013/53/EU Certifying Body: INTERNATIONAL MARINE CERTIFICATION INSTITUTE Rue Abbe Cuypers 3 / B-1040Bruxelles / Belgique Notified Body : 0609 www.imci.org Name of Manufacture: BRIG Ltd. Lozovskaya 88, Dergachy 62303 Kharkovskaya obl. UKRAINE www.brigboats.com 2019 — 4 —...
DANGER LEVELS. The manual contains warnings, identified as follows: A note like this indicates that there is serious risk, that is likely to cause death or permanent serious injury, if appropriate precautions are not taken. A note like this indicates the existence of risk that may cause death or injury, if appropriate precautions are not taken.
Without them the boat does not comply with the legislation in effect. The plates must never be removed. Any tampering or removal not authorised by the manufacturer is the full responsibility of the owner. 2019 — 6 — BRIG...
SAFETY REGULATIONS. This manual contains recommendations and basic rules of conduct for using the boat in complete safety.Although it is not possible to offer safety information for all potential situations, in general it is recommended that you : Regularly check which safety requirements are in force. Maintain the boat and the onboard plants in optimum condition.
NOTE: The significant wave height is the mean height of the highest one-third of the waves, which approximately corresponds to the wave height estimated by an experienced observer. Some waves will be double this height. 2019 — 8 — BRIG...
ALWAYS REMEMBER ABOUT FIRE DANGER . Fire may be caused by: The manufacturer does not supply a fire extinguisher with a boat. A fire extinguisher must be installed on the boat by the owner. Responsibility for choosing the type of fire extinguishers, their number and capacity, as well as the installation location remains with the owner. The owner should also know how to use a fire extinguishers and monitor its suitability.
Loaded displacement mass 2500kg 2500kg 2600kg 2600kg *Maximum recommended load is including weight of the max engine(s), passengers and cargo onboard, but excluding the mass of the contents of fixed fuel and water tanks when full 2019 — 10 — BRIG...
COMPLETE SET . In the table is shown the maximum possible complete set, which may differ from your boat. Description Unit of N700, N730 measure Inflatable boat pcs. Foot pump pcs. Paddle pcs. Set of spare parts and repair kit: - mooring line - coated fabric for repair 0.06...
Page 12
Note. Perfection of the design and improvement of quality of our products is the fundamental production policy of our company. Therefore, alternations may be made to the complete set (and as the components become available). 2019 — 12 — BRIG...
THE MAIN DIMENSIONS. The main dimensions of N700 / N730 have tolerance of +/- 3%. The length of the boat with the engine can vary depending on the model of the engine and the angle of its deviation. (See Fig. D0) N700 / N730 7.81m N700 - 6.99m / N730 - 7.3m...
POLYESTER HULL. The boat hull has "deep-V" shaped bottom with four longitudial steps. The upper deck has a special moulded antiskid coating. There is two specified sections (Fig. D2): — bow locker (1) is intended for arrangement of anchor and anchor rope or for baggage arrangement; —...
— spindle (6) with spring (7) and cup diaphragm (8). Also there are the following elements fitted on the tube (Fig. D1): — doubled rubbing strake (3, Fig.D1); — safety handles (4, Fig.D1); — bow step-plate with a special moulded antiskid coating (6, Fig.D1). 2019 — 18 — BRIG...
STAINLESS STEEL ARC. Stainless steel arc (18, Fig.D1) is located in the stern part of the boat. Arc is equipped with anchor light (white, 21) and running lights: port (red, 19) and starboard (green, 20), (Fig. D1). STEERING CONSOLE. Steering console is located in the central part of the boat. The console consists of the following components (Fig.
Page 20
— shower switch (8); with warning lights Always check the fuse. Burning H ORN red LED display on the fuse box warns of faulty fuse Always keep a spare set the fuse in an easily-accessible location. 2019 — 20 — BRIG...
FUEL SYSTEM. Fuel system consists of the following components (Fig. D6): — built-in fuel tank (1); — electric fuel gauge (2); — outer neck for fuel fill (3); — fuel hose (from outer neck for fuel fill to fuel tank) (4); —...
Do not dispose bulky objects in front of the cockpit drain sockets. Do not modify drain systems. Before navigation check the drain valves. Never locate heavy objects on the drain hoses. It will be cause of bucking, distortions and damages. 2019 — 22 — BRIG...
Page 23
Bilge valve (8)(Fig.D8) should be tightly CLOSED when the boat on the water Bilge valve (8)(Fig.D8) should be open when the boat is out of the water It is dangerous to pretend to be an expert. This may cause damages. Refer to expert and authorized specialists for all types of maintenance and repair.
Do not modify electrics of the boat. When leaving the boat, Any modification, repair and planned maintenance may remember to disconnect be made by authorized representative specialists only. the batteries. Do not touch the electrical equipment with wet hands. PREPARATION FOR EXPLOITATION. In order to set the boat in the operation condition perform as follows: —...
It is possible to install the boat on several reference points. Thereby the point of support (1) must be an obligatory, and the point of support (2), (3), (4) must be an additional. Lateral roller supports can be used only with a view of prevention from tipping. 2019 — 26 — BRIG...
Page 27
Points of support 830+50 3155+50 4475+50 Main load area (keel line) Maximum transportable mass N700 single engine – 1675 kg I n o r d e r t o a v o i d t h e h u l l N700 twin engine –...
— Further, please place two soft cushions onto the false decks and fasten them with the help of press-buttons (Fig. A1d). false deck boards front seat of the steering console Two soft cushions Front locker removable cushion Always check fixation of the sundeck cushions. Fig.A1 2019 — 28 — BRIG...
CREW LIMIT. The number of passengers in the boat is limited. The maximum possible number of passengers is indicated in the technical data and on the builder's plate. Never exceed the crew limit. Always check that the passengers in the boat are sitting in the N700J (N730J) designated seating area.
If you are in the water and the ladder is folded, you can lay it out and get back on board. The ladder can be secured with velcro. Just unplug it. Be careful - the rotating propeller on the engine DO NOT forget to fold the ladder after folded ladder unfolded ladder Fig.A3 2019 — 30 — BRIG...
ANCHORING AND TOWING. Strong points. On the boat there is space to accommodate the anchor (Fig.A4). 1 - anchor storage compartment 2 - inner ring for fixing rope 3 - U-bolt for fixing the anchor / tow rope 4 - bow plate 5 - bow roller 6 - clam-bollard for rope 6-10mm Equip your boat with an anchor of suitable size and type.
Use bow cleat only for mooring in calm water for a short time. If you are leaving the boat and there is a possibility of rough water or strong wind, use only bow U-bolts (3) Fig.A4 to bow mooring. bow cleat stern cleats Fig.A5 2019 — 32 — BRIG...
Page 33
Cleats are designed for a maximum load of 16kN. The breaking strength of rope shall in general not exceed 80% of the breaking strength of the respective strong point. Be careful when mooring. Suddenly tensioned mooring ropes may cause injury. Always have mooring ropes on board in an easily accessible place.
0°C, it must be kept at a temperature above +15°C at least for 1 hour before to be unpacked and unfolded. For small repair boat tube use the coated fabric and glue set from the complete set. 2019 — 34 — BRIG...
OPERATING REGULATIONS. Dear user, We thank your for your purchase and do hope that you will have a great fun of it. However, to make your joy and pleasure complete, we would request you to read carefully and observe the directions and recommendations specified below. IT IS STRICTLY FORBIDDEN to handle the boat in the state of intoxication and without individual rescue means being used (life-saving belts, jackets, etc.) IT IS FORBIDDEN to use an outboard motor of power exceeding the maximum allowable value...
Page 36
Despite the strong shell of the boat we recommend carefully handle and operate with sharp and pricking objects which you have on board . It concerns, for example, a knife blade, fish-hook point, etc. 2019 — 36 — BRIG...
Page 37
Approaching to rocky shores, shoals, moles, etc. , please be careful to avoid damages of your boat. It is strictly prohibited to drag the boat across rough surfaces (shingle, rocks, concrete, etc.). In case of prolonged navigation with the use of an outboard motor, regularly check, that the motor is reliably attached to the boat.
Page 38
Reduce speed before sharp turn, in either direction. When the boat is fitted with an engine with maximum recommended power it must be use with extreme care. This application is directed at experienced users using their boats for very specific purposes. 2019 — 38 — BRIG...
Page 39
Do not operate your boat with an engine of rated power larger than that stated on the builder's plate in the boat. Do not operate this craft at negative propulsion unit trim settings (bow down) at high speed. Craft may lean over on side. Instability in turns may result. Use negative trim to accelerate to planing speed from displacement speed and at lower planing speeds in choppy water (applicable to craft equipped with propulsion unit power trim).
Page 40
Stamp and signature Stamp and signature 6.Steering system Stamp and signature 7.Engine power system 3.Drain system Stamp and signature 4.Bilge pump Stamp and signature 8.Engine installation, test and Stamp and signature completion plantsand fittings done by 2019 — 40 — BRIG...