Hobbico AquaCraft V24 One-Design Assembly And Operation Manual
  1. Manuals
  2. Brands
  3. Hobbico Manuals
  4. Toy
  5. AquaCraft V24 One-Design
  6. Assembly and operation manual

Hobbico AquaCraft V24 One-Design Assembly And Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

ASSEMBLY AND OPERATION MANUAL
• AquaCraft
™
will warrant this kit* for 90 days after the purchase from defects in materials or workmanship. AquaCraft
will either repair or replace, at no charge, the incorrectly made part.
• Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase
and we must see it before we can honor the warranty.
• To return your V24 One-Design for repairs covered under warranty, you should send your boat to:
Thank you for purchasing the V24 One-Design! We at AquaCraft know how exciting a new R/C boat purchase can be and
we know you're anxious to get started, but please take time to read these instructions carefully and completely before
attempting to operate your model. This manual contains the instructions you need to safely operate and maintain your
boat. As with any hobby, there is the possibility of injury. Arming yourself with knowledge is the best way to avoid injury.
If for any reason you think that this model is not for you, return it to your local dealer immediately. PLEASE NOTE:
Your hobby dealer cannot accept a return on any model after the final assembly sequence has begun.
Entire Contents © Copyright 2005
™
by
Warranty
Hobby Services
3002 N. Apollo Drive, Suite 1
Champaign, Illinois 61822
Attn: Service Department
Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F
E-mail: hobbyservices@hobbico.com
*See engine warranty information on page 2
™
HCAZ1003 for HCAB40**

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AquaCraft V24 One-Design and is the answer not in the manual?

Questions and answers

Yoelby Alvarez
April 27, 2025

I need some parts where I find

0
Asitha
April 6, 2025

For this v24 boat engine can replace any other engine or can upgrade this engine to get more speed

0

Related Manuals for Hobbico AquaCraft V24 One-Design

Summary of Contents for Hobbico AquaCraft V24 One-Design

  • Page 1 Attn: Service Department Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F E-mail: hobbyservices@hobbico.com *See engine warranty information on page 2 Thank you for purchasing the V24 One-Design! We at AquaCraft know how exciting a new R/C boat purchase can be and we know you’re anxious to get started, but please take time to read these instructions carefully and completely before...

  • Page 2: Repair Service

    COD or if you wish to be notified of the charges so you can send a check. Your AquaCraft V24 One-Design features a powerful Fuji ™ 24cc BT- Marine engine covered by Fuji Engines’ standard Outside USA and Canada, contact local importer for 3-Year Limited warranty.

  • Page 3: Boat Terminology

    STARBOARD: This is the right side of the boat when aboard AND OTHER USEFUL TOOLBOX ITEMS and facing the front (bow). The AquaCraft V24 One-Design can be made ready for the HULL: The body of the boat. water in just a few minutes. The following sizes of hex keys are supplied with the V24: 1.5mm, 2mm, 2.5mm, 3mm, and 4mm.

  • Page 4: Transmitter Assembly

    TRANSMITTER ASSEMBLY V24 ONE-DESIGN FINAL ASSEMBLY Important Note: The transmitter is not water resistant ASSEMBLE THE DISPLAY/WORK STAND and should never come in contact with water. ❏ 1. Remove the transmitter antenna from the parts bag and screw it into the top of the transmitter. To ensure that the antenna is attached, lightly pull on the base of the antenna.
  • Page 5 INSTALLATION OF RECEIVER BATTERIES ❏ 3. Place four (4) new “AA” batteries into the receiver battery holder. Be sure to follow the polarity diagram molded into the battery holder. ❏ 4. Replace the battery holder inside the radio box. Make sure that it will not interfere with any of the control linkages.
  • Page 6 ❏ ❏ 3. Slide the tuned pipe brace onto the small end of the 5. Place the tuned pipe brace onto the pipe brace mount tuned pipe as shown. on the transom as shown and secure it with the 4mm nut. ❏...
  • Page 7 FUEL Once the engine is broken in, use 40:1 (2.5% oil) fuel/oil mix. Always use high quality oil intended for 2-cycle engines. Prepare only the amount of gasoline needed. Aged gasoline could damage the engine and cause it to overheat. Use only low octane, alcohol-free gasoline.

  • Page 8: Idle Adjustment

    IDLE ADJUSTMENT: BREAKING IN THE ENGINE Important: Do not confuse the idle screw with the low-speed needle “L”. The idle screw physically adjusts how much the To ensure long life and good performance from your Fuji BT- carburetor valve can close. The low-speed needle “L” adjusts 24 Marine engine, you MUST break it in properly.
  • Page 9 STARTING THE ENGINE AND LAUNCH PROCEDURE There are several simple steps to starting the engine. It is a good idea to have another person hold the boat in place while you start the engine. STARTING PROCEDURE: IMPORTANT: The propeller will begin spinning as soon as the engine starts! Be certain that the propeller is unobstructed;...
  • Page 10 9. Gently place the boat in water that is at least 8" deep and • R/C models produce vibrations which will cause screws, free of obstacles (weeds, rocks, sticks, ducks, muskrats, etc.). nuts, bolts, etc, on your model to become loose over time. Be sure to stay clear of the spinning prop during the launch.

  • Page 11: The Waiting Game

    • CAUTION: Windy conditions cause rough water that will affect the performance of your V24 and increase the chances of capsizing. • Your V24 may take on water when running in rough conditions and when making tight turns. Keep a roll of paper towels handy and dry out the hull interior after every run.

  • Page 12: Engine Maintenance

    • Should moisture gain access to the radio box, all cause the boat to submerge in a turn. connections should be dried thoroughly. Hobbico “Duster” Compressed Air (HCAR5500) will provide a blast of air Be sure to retighten all the screws upon establishing the capable of blowing moisture out of connectors.

  • Page 13: Channel Operation

    3-CHANNEL OPERATION RACING The optional third channel will allow you to adjust the strut Although it is very enjoyable to run the V24 by yourself, the and prop angle while the boat is in motion. This option is real fun and excitement of R/C boating is experienced when used mainly by serious racers who need to fine-tune their you get involved in racing.
  • Page 14 NATIONAL MODEL BOATING ORGANIZATIONS SUGGESTIONS FOR SETTING UP A SIMPLE RACECOURSE There are three national model boating organizations in the United States and Canada: APBA or American Power Boat Association (RC Boat Category) GALLON-SIZE www.apba-rcboating.com PLASTIC MILK JUG IMPBA or International Model Power Boat Association www.impba.net NYLON STRING NAMBA or North American Model Boat Association...

  • Page 15: Ordering Replacement Parts

    (screws, nuts, bolts) are also available from these outlets. If you need assistance locating a dealer to purchase parts, visit www.hobbico.com and click on “Where to buy”. If this kit is missing parts, contact Hobbico Product Support. ORDER #...
  • Page 16 Recoil Starter 5 ..FJIG6635 ..........Piston Ring 6 ..FJIG6361 ...........Piston Set 7 ..FJIG6419 ...........Piston Pin 8 ..FJIG6509 ........Piston Pin Circlip 9 ..FJIG8719.......Water Jacket Complete 10 ..FJIG7160 ...........Screw 3x8 11 ..FJIG4019 ........Crankshaft Complete 12 ..FJIG6149 ......Needle Bearing 1.4x8.5 13 ..FJIG7660 ..........Woodruff Key 14 ..FJIG6260 ............O-Ring 15 ..FJIG7500......Spark Plug Cap Assembly Carburetor...

Table of Contents