Table of Contents
Advertisement
Quick Links
ASSEMBLY AND OPERATION MANUAL
•
AquaCraft
will warrant this kit for 90 days after the purchase from defects in materials or workmanship. AquaCraft will
™
either repair or replace, at no charge, the incorrectly made part.
•
Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase
and we must see it before we can honor the warranty.
•
To return your Nitro Hammer
We want the assembly and operation of this boat to be a success so BEFORE removing any parts from the parts bags please
read this manual thoroughly and watch the included video to familiarize yourself with the model. If for any reason you
think this model is not for you, return it to your local dealer immediately. PLEASE NOTE: Your hobby dealer cannot accept
a return on any model after assembly has begun.
Entire Contents © Copyright 2002
for repairs covered under warranty you should send your boat to:
™
Hobby Services
1610 Interstate Drive
Champaign, Illinois 61822
Attn: Service Department
Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F
E-mail: hobbyservices@hobbico.com
Before Building:
™
Warranty
™
HCAZ3012 for HCAB26**
Advertisement
Table of Contents
Related Manuals for Hobbico Nitro Hammer
Summary of Contents for Hobbico Nitro Hammer
- Page 1 ™ Warranty • AquaCraft will warrant this kit for 90 days after the purchase from defects in materials or workmanship. AquaCraft will ™ either repair or replace, at no charge, the incorrectly made part. • Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase and we must see it before we can honor the warranty.
-
Page 2: Table Of Contents
Avoid working over a deep pile carpet. If you drop a small part or screw, it will be difficult to find. Thank you for purchasing the AquaCraft Nitro Hammer! This manual contains the instructions you need to safely build, •... -
Page 3: Screw Information
The thread- locking compound may damage the plastic. IMPORTANT: Carefully remove your Nitro Hammer from the box and place Use thread lock on any fastener that is threaded into metal or it atop the pre-built boat stand. Remove all remaining fastened with a nut. -
Page 4: Running The Engine
4. Slide the antenna wire through the antenna tube and place the antenna tube into the rubber grommet. DO NOT CUT OFF THE EXCESS ANTENNA WIRE! Installation of Batteries 1. Place four (4) new “AA” batteries into the receiver battery holder. Be sure to follow the configuration molded into the battery holder. -
Page 5: Breaking In The Engine
Nitro Hammer securely held in place. ENGINE MAINTENANCE To insure long life and good performance from your AquaCraft Ways To Ensure A Long Life For Your Engine. Pro .15 engine, you MUST break-in the engine. The break-in period is critical for long life of the internal parts of the engine. - Page 6 Make sure you have a spare plug or two on hand every time that you run the Nitro Hammer. • CAUTION: The engine will be hot! Allow it to cool for a few minutes before restarting.
-
Page 7: Performance Tricks And Tweaks
PERFORMANCE TRICKS AND TWEAKS If you are thinking about modifying your Nitro Hammer, keep this in mind: A tremendous amount of research and development has gone into the Nitro Hammer with speed, stability, maneuverability and run time as our primary •... -
Page 8: Ordering Replacement Parts
The Waiting Game If your Nitro Hammer should happen to stall or capsize, water currents will slowly carry it to shore. The bad news is that the boat could be carried to the opposite shore. When surveying areas to run your Nitro Hammer, keep in mind things like wind direction, size of the lake, strength of river currents, etc.
Need help?
Do you have a question about the Nitro Hammer and is the answer not in the manual?
Questions and answers