Page 1
SaMASZ Sp. z o.o. Poland, 16-060 Zabłudów, ul. Trawiasta 1 Established – 1984 NIP PL-966-159-29-76 tel. (+48) (85) 664 70 31 fax (+48) (85) 664 70 41 e-mail: samasz@samasz.pl www.samasz.pl OPERATOR'S MANUAL ROUND BALE WRAPPER Spin S Spin F IN129USA001 Serial no.:...
Page 2
NOTE: Always turn off the engine and remove the ignition key before entering or servicing the machine, lifting side guards, setting rotor sensors or discharging unwrapped bales. It is forbidden to mount the machine during operation. NOTE: Operating bale wrapper without previous familiarizing with its contents as well as by unauthorized personnel, particularly by children, is strictly forbidden.
1. IDENTIFYING THE MACHINE Data plate (Fig. 2) for bale wrapper is mounted on the frame in place shown below on Fig. 1. Fig. 1. Data plate placement SPIN S Fig. 2. Data plate Fig. 3. Data plate placement SPIN F Fig.
Round bale wrapper Operator's Manual Spin S, Spin F 2. INTRODUCTION General information Prior to operating the machine its user must familiarize himself with this manual as well as common work safety rules. The machine is manufactured in compliance with European safety standards.
Round bale wrapper Operator's Manual Spin S, Spin F 3. TECHNICAL DESCRIPTION 3.1. Technical data Tab. 1. Technical data Designation Unit SPIN S SPIN F Coupling with the tractor Hitched Undercarriage type Mono-axial Overall dimensions in the working setup 14' 3"/ 8' 10"-12' 4"/ 8' 19' 10"/ 9' 10"/ 8' 2"...
Round bale wrapper Operator's Manual Spin S, Spin F 3.2. Wrapping machine construction The SPIN S wrapping machine consists of the following assemblies (Fig. 5): Film movement diagram Fig. 5. Wrapper design SPIN S 1. Main frame 8. Cutting assembly 2.
40 HP and traction class of at least 0.9. The SPIN S and SPIN F bale wrapping machines are designed to pick up bales from the ground, wrap them in film and unload to the ground.
Round bale wrapper Operator's Manual Spin S, Spin F 4. SAFETY PRECAUTIONS During operation and repair of the wrapping machine, all relevant farming health and safety regulations must be complied with. Only an adult with a valid farming tractor driver’s license and familiarized with the occupational health and safety regulations regarding the farming equipment and the following manual may operate this machine.
Round bale wrapper Operator's Manual Spin S, Spin F NOTE:Failure to comply with above instructions may lead to serious injury or death. 4.2. Hazards Description of residual risks Residual risk results from incorrect actions of the wrapping machine‘s operator. The greatest...
The levers of the control unit should remain in the tractor’s cabin, Place the red and white warning symbols equipped with integrated lights, connect them to the tractor’s electric system and check their operation (for: SPIN S), Place the triangle denoting slow-running vehicles in the stand in the rear.
Fig. 8. SPIN F in transport position Fig. 9. SPIN S in transport position 4.5. Warning signs and their meanings NOTE:...
Page 13
Round bale wrapper Operator's Manual Spin S, Spin F 1. Refer to the operating manual 2. Turn off the engine and 3. Do not stand near the links of before performing this action remove the ignition key the operating wrapping...
Page 14
Use the required Personal Protective Equipment 19. 40x950 warning sign 20. 50x300 warning sign 21. 40x800 warning sign 22. CE requirements confornity symbol Fig. 10. Location of pictograms – right side - SPIN S - 12 -...
Page 15
Round bale wrapper Operator's Manual Spin S, Spin F Fig. 11. Location of pictograms – left side - SPIN S Fig. 12. Location of pictograms – right side - SPIN Fig. 13. Location of pictograms – left side - SPIN F...
The wrapping machine SPIN F shall be coupled to the lower hitch or to the upper hitch allowing for the maximum vertical load of 1.2 kN. The wrapping machine SPIN S shall be coupled to the lower hitch or to the upper hitch allowing for the maximum vertical load of 4.7 kN.
Round bale wrapper Operator's Manual Spin S, Spin F Fig. 15. Drawbar set for connection with the upper hitch Change the position of the transport hitch in the following way: o Undo the four nuts and remove the M16 bolts, o Rotate the transport hitch by 180°,...
Round bale wrapper Operator's Manual Spin S, Spin F 6. COMMISSIONING The commissioning of a newly purchased bale wrapping machine should be performer under the supervision of an experienced operator or a dealer’s service representive. IMPORTANT: Before commissioning, familiarize yourself with the following manual, paying special attention to the fragments regarding the safety of the operator and bystanders.
7. CONTROLS AND ONGOING ADJUSTMENTS 7.1. Location of the controls 7.1.1. Wrapper SPIN S Fig. 16. Spin S control lever and control lever pictograms Symbols listed from left to right: o Rotary table movement, o raising and lowering of the rotary table, o Loading arm movement.
Round bale wrapper Operator's Manual Spin S, Spin F Location of ongoing adjustment points 7.2. Fig. 18. Wrapping film feeder With each revolution of the rotating frame, the bale and film rotate by a certain angle around the horizontal axis, which causes the consecutive layers of film to be wrapped tightly around the bale.
Page 21
5 – Hydraulic control unit. 6 – The revolutions sensor is marked with a symbol located on the machine. Fig. 20. SPIN S control and currentadjustment elements 7.2.2. Wrapper SPIN F Fig. 21. SPIN F control and current adjustment elements...
Round bale wrapper Operator's Manual Spin S, Spin F 8. WRAPPING MACHINE OPERATION 8.1. Installing the film Place the film roll on the feeder pin in the following order (see diagram: Deflect the support with the metal rollers and secure it using the hook attached to the wrapping assembly.
(1). The three section control unit (1) is protected against high pressure from the hydraulic system by means of a safety valve (1) (SPIN S), four section control unit (SPIN F). The 3- sectional control unit (1) (SPIN S) or 4-sectional (SPIN F) is protected against high pressure from the hydraulic system by means of a safety valve.
Round bale wrapper Operator's Manual Spin S, Spin F 8.3. Wrap counter 8.3.1. Wrap counter system Wrap counter L-02 The wrap counter is an electronic device used for counting the wraps on a bale and may be used on all types of wrapping machines. The wrap counter should be installed in the tractor’s cabin in a place where it is visible and accessible to the operator.
Page 25
Round bale wrapper Operator's Manual Spin S, Spin F CAUTION! Protect the wires connecting the sensor with the revolution counter against accidental mechanical damage. CAUTION! Protect the connections of the wires with the revolution counter against accidental uncoupling. 8.3.2. Switching the system on and off The blinking red signalling light indicates that the revolution counter system has been configured properly.
Round bale wrapper Operator's Manual Spin S, Spin F Example of the L02 wrap counter indications 8.4. Wrapping 8.4.1. Wrapper SPIN S To prepare the machine for work, it’s side wheel needs to be placed in its working position following the diagram below (Fig. 25).
Page 27
NOTE: The tractor approaching the bale should drive paralel to the bale’s axis so that the axis of the loading arm faces the axis of the bale being loaded (SPIN S). NOTE: The axis of the wrapping machine moving forward should be perpendicular to the loaded bale axis and the lowered arm should hold the bale (SPIN F).
Page 28
Round bale wrapper Operator's Manual Spin S, Spin F Fig. 27. SPIN S bale loading Fig. 28. SPIN F bale loading Stop the tractor when the bale rests against the stop plate of the lateral loading arm. Lift the grab arm until the bale rolls freely onto the wrapping machine rotary table. Lower the grabbing arm to the bottom when the bale rests on the rotary table.
In SPIN S bale wrapper the conical Rolls located on the sides of the rotary frame prevent the film from falling off the drums while wrapping.
Page 30
Operator's Manual Spin S, Spin F Fig. 29. Bale discharge a) SPIN S; b) SPIN F In SPIN F bale wrapper during the unloading proces, the cutter cuts away the film. The bale on the unloading unit rotation control level as shown in the Fig. 30. After unloading the bale, all working components should return to their position.
Page 31
Side wheels located on the sides of the rotary frame prevent the bale from falling off the drums while wrapping. 8.5.2. Bale vertical positioning system – optional equipment SPIN S model As optional supply, a bale vertical positioning system is available. This device allows to position the wrapped bale vertically during unloading, in order to properly place it in the silage storing location.
Round bale wrapper Operator's Manual Spin S, Spin F Fig. 33. Drive chain adjustment Check the tightening and the chain conditio periodically after wrapping every 120 bales. 8.7. Finishing work After the worki s complete, disconnect the revolution counter and secure the revolution sensor against humidity.
Round bale wrapper Operator's Manual Spin S, Spin F 9. REGULAR INSPECTION 9.1. User inspection After every use of the wrapping machine, check: The conditio and legibility of the data plate and symbols, Condition of the drawbar, Hydraulic system leakproofness, Drive chain of the rotary frame, Drive chains of the rotary drums.
Round bale wrapper Operator's Manual Spin S, Spin F 10. AUTHORISED SERVICE 10.1. Warranty service The manufacturer issues a warranty on conditions described in the warranty book. During the period covered by the warranty, repairs shall be made at authorised service stations or at the manufacturer’s service.
Round bale wrapper Operator's Manual Spin S, Spin F 11. WRAPPING MACHINE STORAGE After yhe working season is over, clean the wrapping machine and check the conditio of the protective paint coating. Touch up the damage to the paint coating at a service workshop. Check the conditio and legibility of the nameplate.
Round bale wrapper Operator's Manual Spin S, Spin F DISASSEMBLY AND WITHDRAWAL FROM USE During machine disassembly, separate the parts made of the same material. Keep liquids, metal parts, rubber, plastic, separate. Disassembly and disposal of the wrapping machine should be performed by specialised service stations familiarised with the construction and functioning of the machine.
Round bale wrapper Operator's Manual Spin S, Spin F 15. WARRANTY CONDITIONS 15.1. Warranty claims procedures 1. The manufacturer provides a bale wrapping machine designed and built in compliance with the currently applicable standards. The manufacturer guarantees that the supplied bale wrapping machine is free of manufacturing defects.
Round bale wrapper Operator's Manual Spin S, Spin F 15.2. Record of warranty repairs Repairs performed and parts replaced: Date, seal and signature of person performing the repair Date, seal and signature of person performing the repair Date, seal and signature of person performing the repair...
Need help?
Do you have a question about the Spin S and is the answer not in the manual?
Questions and answers