Table of Contents
Advertisement
Quick Links
A S S E M B LY I N S T R U C T I O N S
The Newport Arbor
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Posts (4) - 4" x 4" x 84" - 10122
2. Molded Arches (4) - 10552
3. Locking Arch/Post Inserts (4) - 4" Sq - 10163
4. Trim Caps (4) - 4" Sq - 10082
5. Rafter End Caps (20) - 1 3/4" Sq - 30021
6. Top / Bottom Rails (4) - 1 3/4" x 1 3/4" x 31 5/8" - 10060
7. Middle Rails (2) - 1 3/4" x 1 3/4" x 31 5/8" - 10143
8. Rafters (10) - 1 3/4" x 1 3/4" x 39" - 10142
9. Spindles (10) - 7/8" x 1 1/2" x 58" - 10141
10. Keystone Base & Locking Top (2) - 10430
11. 3/4 in Stainless Steel Screws (32) - 20016
12. 3 in Stainless Steel Screws (20) - 20007
13. Tubes of Vinyl Glue (2) - 20000
Material You Will Need (Not Included)
• 4 in x 4 in x 4 ft Pressure Treated Lumber (4)
Tools You Will Need
• Hammer
• Tape Measure
• Level
• Stool or Short Ladder
• Shovel or Auger
• Cordless Drill
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 10'x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.
84 in
93 3/4 in
87 1/2 in
50 in
58 in
5
8
2
3
4
6
7
1
9
10
www.newenglandarbors.com
45 in
24 in
32 in
11
12
13
V2.0/101916
(Not to scale)
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for New England Arbors Newport
Summary of Contents for New England Arbors Newport
-
Page 1: General Information
A S S E M B LY I N S T R U C T I O N S The Newport Arbor www.newenglandarbors.com 84 in 45 in 93 3/4 in 87 1/2 in 50 in 24 in 58 in 32 in Please read through before starting assembly. - Page 2 Set out a second post. Flip the entire panel over and line up the rail ends with the corresponding holes in the post. As in step 2 above, push the end of each rail into the holes until the locking tabs are completely inserted. Repeat steps 1through 3 for second side panel. The Newport Arbor...
- Page 3 If you’re using concrete to install the arbor (recommended), insert a 4 x 4 x 48” treated lumber 12” into the posts as shown. Fasten the wood insert with screws (not included). www.newenglandarbors.com Note: If you’ve purchased the Aussie Auger mounts, please refer to those instructions to complete the installation. The Newport Arbor...
- Page 4 Flip the arch over and slip each arch couplers into the bottom of the arch. Push firmly until they snap into place. No glue is required for this step. Repeat steps one through five for the second arch. The Newport Arbor...
- Page 5 Repeat this step for each end cap. Note: Allow 10 minutes for the vinyl glue to set before lifting or moving the arch assembly. Note: Avoid the guide pin when fastening the screw. www.newenglandarbors.com The Newport Arbor...
- Page 6 Run a 2” - 3” long bead of glue on the ribbed flanged of the arch couplers as shown. Place the arch assembly over and into the side panel posts. (You will need a helper). 36 in. 91.4 cm. 12 in. 30.5 cm. The Newport Arbor...
- Page 7 S T E P F I V E Run a bead of glue around the post just under the arches. Slide the post trims up and hold them in place momentarily to allow the glue to set. Fasten four 3/4in screws into each side of the post just below the post trim.
Need help?
Do you have a question about the Newport and is the answer not in the manual?
Questions and answers