Page 1
L810-MiniPCIe Hardware User Manual Version: 2.0.0 Update date: 2015.10.31 The document is copyrighted by Fibocom Wireless Inc., and shall not be reproduced without permission. Page 1 of 26 L810-MiniPCIeHardware User Manual...
Page 2
Applicability Table Product model Description L810-GL-MiniPCIe Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 2 of 26...
Page 3
Update SIM name in pin definition V1.0.2 2015-08-25 Update the company logo V2.0.0 2015-10-31 Adjust document content and format Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 3 of 26...
5.3.2 I2S Application Description......................19 5.3.3 Application Description for PCM Mode..................19 5.4 UART Interface..........................20 5.4.1 UART Interface Description......................20 5.4.2 UART Interface Application......................20 Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 4 of 26...
Page 5
6.2 Product Weight...........................24 6.3 Environmental Temperature......................24 7 Product Packaging........................25 7.1 Palletizing process is shown in Figure 7-1:................25 7.2 Pallet size............................25 Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 5 of 26...
1.1 Introduction The document describes the electrical characteristics, RF performance, dimensions and application environment, etc. of L810-MiniPCIe. With the assistance of the document and other instructions, developers can quickly understand the performance of L810-MiniPCIe and develop products. 1.2 Reference Standard The design of the product complies with the following standards: Mini PCI Express Card Electromechanical Specification Revision 1.0-2003...
The chapter gives a detailed introduction of the functional interface and antenna interface of L810-MiniPCIe. 2.1 Mini PCIe Interface Except for 4 digital voice pins, L810-MiniPCIe module applies standard Mini PCIe interface. And the pin definition is as follows: Pin name...
Page 8
3.3V UART1_TX UART1 data transmit signal 3.3V UART1_CTS UART1 clear to send signal 3.3V UART1_RTS UART1 request to send signal 3.3V Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 8 of 26...
Page 9
PU: Pull-Up T: Tristate OD: Open Drain PP: Push-Pull Note: The unused pins can be left floating in case of circuit design. Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 9 of 26...
2.2 Antenna Interface L810-MiniPCIe antenna adopts 50 ohm RF interface and supports main and diversity antennas. It adopts HIROSE U.FL-R-SMT(01) antenna connector. Figure2-1 Antenna Interface Please refer to the following website for more information about RF connector: http://www.hirose-connectors.com/ Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved...
As for the power supply to the module, the rising time for voltage after powering on is described in Figure 3-1: Figure3-1 Rising Time for Power Supply Timing description Requirement Rising time from 2.5V to 3.3V less than 5 ms Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 11 of 26...
The effective voltage ranges listed in the following tables: Parameter Minimum value Recommended value Maximum value Unit 3.3VAUX -0.5 Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 12 of 26...
2A current. In case of PCB design, the width of the power traces must be sufficient to support the maximum current. If the design requirements are not followed, the module might shutdown while it is working. Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 13 of 26...
4 Radio Frequency 4.1 Frequency Band Partition L810-MiniPCIe provides two radio frequency connectors for the master and diversity respectively, and the master is used to receive and transmit RF signal, and the diversity is used to receive the RF signal.
The RF traces must have 50 Ohm impedance. If the impedance is not matched, the RF performance will reduce. Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 15 of 26...
Windows system before it can be used in PC. After L810-MiniPCIe is inserted into PC, the USB driver will map 3 COM ports and 3 NCM ports on the Windows system, which are shown as follows: ...
Power supply for external USIM card 1.8V/3V USIM_IO USIM data signal 1.8V/3V USIM_CLK USIM clock signal 1.8V/3V USIM_RST USIM reset signal 1.8V/3V Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 17 of 26...
ESD device (e.g. TVS diodes) shall be added close to the SIM card pins for ESD protection. The capacitance for ESD devices should be lower than 33pF. Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual...
5.3 Digital Audio Interface 5.3.1 Audio Interface L810-MiniPCIe supports I2S digital audio interface, and it supports the ordinary l2S mode and PCM mode. The signal level of the l2S interfaces is 1.8V. Description for l2S signals is as follows: Pin name...
For PCM mode, the audio quality issues caused by the PCM timing adjusting must be avoided. 5.4 UART Interface 5.4.1 UART Interface Description L810-MiniPCIe provides one four-line UART, and the user can receive and send AT command through UART1 and auto baud rate is supported. Pin name Pin description...
1s low level, then change to high level (pulse signal) 5.5 Reset signal L810-MiniPCIe supports external reset function, and the module can be reset to the initial status through PERST# signal. Description for PERST# signal is as follows: Pin name...
Pulses with 75ms high then 75ms low. Sleep (sleep mode) High level LPG timing is shown in Figure 5-4: Figure 5-4 Time Sequence for LPG Signal Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 22 of 26...
5.7 W_DISABLE Signal L810-MiniPCIe provides a hardware pin to enable/disable WWAN RF functional, and the function can also be controlled by the AT command. The module enters Flight mode after RF function is disabled. Description for W_DISABLE signal is as follows:...
6.2 Product Weight Weight for L810-MiniPCIe is about 9 grams. 6.3 Environmental Temperature Parameter Minimum value Maximum value Unit Storage temperature °C Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 24 of 26...
The pallet size is 260*175*6.5mm. 20pcs are packed in each pallet, with 5 pallets in each box and 6 boxes in each case; please refer to Figure 7-2: Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual...
Page 26
9.5±0.3 0.5±0.1 51.5±0.3 30.5±0.3 ITEM 307.5±0.5 156.0±0.5 12.5±0.3 12.0±0.3 18.0±0.3 64.0±0.2 ITEM 192.0±0.2 84.0±0.2 9.0±0.2 Figure 7-2 Pallet Size (Unit: mm) Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved L810-MiniPCIeHardware User Manual Page 26 of 26...