Add headphone MIC design note Optimized version V2.0.0 04-27-2018 Add supported band descriptions of other sc806 models The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage2 of 70...
Page 3
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage3 of 70...
Page 4
“Contains FCC ID: ZMOSC806AM”.The grantee's FCC ID can be used only when all FCC compliance requirements are met. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage4 of 70...
SC806-CN-02 SC806-CN-00. SC806-AM-00 support 5G WIFI SC806-AB-00 support 5G WIFI SC806-AE-00 support 5G WIFI SC806-CN-01 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage5 of 70...
USB Interface ......................... 32 UART Interface ........................34 USIM Interface ........................34 SDIO Interface........................36 GPIO Interface........................37 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage6 of 70...
Page 7
Overview ........................55 8.1.1 Performance parameters ....................55 8.1.2 Electrical Characteristics and Reliability ....................55 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage7 of 70...
Page 8
Appendix C GPRS Multislot ......................69 Appendix D EDGE Modulation and Encoding Method ..............70 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage8 of 70...
Page 9
Table 37 Module antenna requirement ..................... 49 Table 38 WIFI transmission power table ..................... 52 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage9 of 70...
Page 10
Table 50 Multilevel multislot allocation ....................69 Table 51 EDGE modulation and encoding method ................... 70 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage10 of 70...
Page 11
Figure 21 Recommended PCB Welding Plate Design (Unit: mm) .............. 61 Figure 22 Tray Packaging ........................63 Figure 23 Tray Dimension ........................64 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage11 of 70...
DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS) 1.3 Related documents The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage12 of 70...
GPS /GLONASS /BeiDou The SC806 is a module with 210 pins, including 146 LCC pins and 64 LGA pins. The size is 40.5mm × 40.5mm × 2.8mm. It can be embedded in various M2M products through welding plate. It is very suitable for the development of mobile devices such as on-board computers, multimedia devices, smart homes, and Internet of Things devices.
Page 14
Class AB stereo headphone output Class AB differential handset output Class D differential speaker amplifier output The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage14 of 70...
Baseband Wireless transceiver Storage Peripheral interface -- Communication expansion interface (USB/UART/I2C/SDIO) The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage15 of 70...
SC806module adopts LCC+LGA packaging, with a total of 210 pins, including 146 LCC pins and 64 LGA pins. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage16 of 70...
Note: The pin “NC” stands for No connect, ie the pin for this position is a reserved pin and does not need to be connected. 3.1.2 Pin Definition Table3I/O parameter definition Type Description input/output The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage17 of 70...
Page 18
2.95/1.8 Vadjustable, 55mA RTC clock power supply VRTC Voltage range: 2.0 ~3.25V, recommend 3.0 V 3,7,12,15,27,51,62, Ground The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage18 of 70...
Page 19
Connect indicator negative Button Pin Name Pin No. Pin Description Note KEY_ON/OFF Analog switch button Low effect The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage19 of 70...
Page 20
SD card clock cardcommand SD_CMD interface SD_DET SD card detection Low level is effective I2Cinterface The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage20 of 70...
Page 21
Debug port UART1_RX UART1 data reception Debugport MIPI-DSIinterface Pin Name Pin No. Pin Description Note The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage21 of 70...
Page 22
MIPI_CAM0_CLK_M MIPI_CAM0_D1_P AI/AO MIPI_CAM0_D1_M AI/AO Main camera MIPI differential clock signal MIPI_CAM0_D0_P AI/AO MIPI_CAM0_D0_M AI/AO The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage22 of 70...
Page 23
REC_P Receiver differential output REC_M Headphone left channel HPH_L output Headphone right channel HPH_R output The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage23 of 70...
Page 24
Pin Description Note GPIO_0 B-PD:nppukp GPIO_8 B-PD:nppukp Ordinary GPIO, 1.8V power domain B-PD:nppukp GPIO_9 B-PD:nppukp GPIO_10 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage24 of 70...
Page 25
GPIO_92 B-PU:nppdkp GPIO_93 B-PD:nppukp GPIO_94 B-PD:nppukp GPIO_95 B-PD:nppukp GPIO_96 B-PD:nppukp GPIO_97 B-PD:nppukp GPIO_98 B-PD:nppukp GPIO_99 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage25 of 70...
3.2 Power The SC806 provides four VBAT pins for connecting to an external power: two VBAT_RF pins are used for the RF power supply of the module, and two other VBAT_BB pins are used for baseband power supply of the module. The power input range is from 3.3V to 4.5V, and the recommended value is 3.8V.
Page 27
6.8pF 0/2600MH interference The power voltage drop example is shown in the figure: The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage27 of 70...
3.2.2 Lithium Battery Charge and Battery Management If the SC806 is powered by a battery, it uses a lithium battery with temperature detection function. The SC806 has a battery temperature detection function. The battery requires internal integration of a thermistor (default is 47K±1%, B=4050 NTC), and the battery temperature detection pin is connected to the BATT_CON_TEMP pin (PIN 134).
Programmable Range (V) Default Voltage (V) Drive Current (mA) VDD_1V8_L5 VDD_1V8_L6 VDD_2V85_L17 2.85 VDD_SD_L12 2.95 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage29 of 70...
2 seconds. The KEY_ON/OFF control reference diagram is as follows: Figure 6Button Startup Circuit The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage30 of 70...
3.3.2 Module Shutdown and Restart After the SC806 is powered on, set the low KEY_ON/OFF signal to more than 500ms, the display interface will pop up a selection box (select shutdown or restart). If it is greater than 10s, the system will be forced to shutdown.
The USB_VBUS power is a USB power or an adapter. It can be used as a USB plug-in detection and charge the The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.
Page 33
Table11module internal USB trace length Pin No. Pin name Length (mm) Length error (DP-DM) USB_DM 28.70 -0.51 USB_DP 28.19 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage33 of 70...
USIM1 power supply, 1.8V/2.95V VDD_USIM1_L14 USIM1 data signal USIM1_DIO USIM1 clock signal USIM1_CLK USIM1 reset signal USIM1_RST The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage34 of 70...
Page 35
2) The layout and route of the SIM card must be kept away from EMI interference sources such as RF antenna and digital switch signal. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage35 of 70...
2) Pull up SD card data, clock and command trace with VDD_SD_L12, and pull up SD_DET with VDD_SD_L5 3) SDIO, a high-speed digital signal trace needs to be shielded. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage36 of 70...
GPIO_32 GPIO_36 B-PD:nppukp B-PD:nppukp GPIO_58 GPIO_65 B-PD:nppukp B-PD:nppukp GPIO_68 GPIO_69 B-PD:nppukp B-PD:nppukp GPIO_88 GPIO_89 B-PD:nppukp The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage37 of 70...
KP:nppdpu = default keeper with programmable options following the colon (:) 3.9 I2C Interface The SC806 provides three I2Cs for TP, CAMERA, SENSOR, etc.. The I2C interface has a pull-up resistor of 10K to VDD_1V8_L6 inside the module. Table16I2C pin definition Pin No.
The SC806 video output interface is based on the MIPI_DSI standard and supports 4 sets high-speed differential The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage39 of 70...
3.13 Touch Screen Interface The SC806 provides one set I2C interface that can be used to connect the touch screen (TP), and provides power and interruption pin. The TP pin definition of the module is shown in the following table: Table20TP pin definition Pin No.
I2C_SDA_TP Touch screen I2C data 3.14 Camera Interface The SC806 video input interface is based on the MIPI_CSI standard, and supports two cameras, and up to 8MP pixel cameras. MIPI-CSI0 is 2 Lane interface, and supports up to 8M Camera MIPI-CSI1 is 1 Lane interface, and supports up to 5M Camera 3.14.1 Front camera...
MIPI DSI/CSI is a high-speed data trace. It has a relatively high requirement for routing, so priority should be The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage42 of 70...
Page 43
12.74 MIPI_CAM0_D0_P -0.16 12.90 MIPI_CAM0_D0_M 16.41 MIPI_CAM1_CLK_P -0.10 16.51 MIPI_CAM1_CLK_M 17.64 MIPI_CAM1_D0_P 0.51 17.13 MIPI_CAM1_D0_M The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage43 of 70...
Headphone detection signal input HPH_DET HPH_GND Headphone ground MIC1_P Main MIC single-end input MIC ground MIC_GND The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage44 of 70...
Tx (MHz) Rx (MHz) Band 2 LTE FDD/WCDMA/GSM 1850-1910 1930-1990 Band 4 LTE FDD/WCDMA 1710-1755 2110-2155 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage45 of 70...
4.1.2 Reference Design For use of the SC806,the antenna pin and the RF connector or antenna feed point on the main board should be connected via an RF trace. Microstrip trace is recommended for RF trace, with insertion loss within 0.2dB, and impedance at 50ohm.
4.2.2 Reference design WIFI/BT antenna connection reference design is shown as follows Figure 13WIFI/BT Antenna Connection The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage47 of 70...
Microstriptrace is recommended for the GNSS RF route, with insertion loss within 0.2dB, and impedance at 50 ohms. The connection reference design is shown as follows: The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage48 of 70...
Polarization type: right-circular or linear polarization GNSS VSWR: < 2 (typical) Passive antenna gain: > 0dBi The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage49 of 70...
50Ω. Microstriptrace complete structure Figure 15Two-layer PCB Microstrip Structure Coplanar waveguide complete structure The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage50 of 70...
Page 51
The impedance simulation tool should be used to accurately control the RF signal trace at 50Ω impedance. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage51 of 70...
MHZ) Spec(dB) Margin(dB) 1Mbps 17.0±2 >5 802.11b 2.4G 11Mbps 17.0±2 >5 802.11g 6Mbps 16.0±2 >5 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage52 of 70...
Page 53
IEEE Std 802.11b, IEEE Std 802.11d, IEEE Std 802.11e, IEEE Std 802.11g, IEEE Std 802.11i: IEEE 802.11-2007 WLAN MAC and PHY, June 2007 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage53 of 70...
7.1.4 Bluetooth performance parameters Table36BT performance parameters Type DH-5 2-DH5 3-DH5 Unit 11±1 10±1 10±1 Transmitter Sensitivity The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage54 of 70...
Table38Recommended parameters Parameter Nominal Unit Vbat USB_VBUS 4.35 VRTC 3.25 Operating ℃ Temperature ℃ Storage Temperature The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage55 of 70...
DRX=8 WCDMA 3.44 FDD LTE DPC(DefaultPaging Cycle)=#256 2.33 Isleep Radio Off AT+CFUN=4 Flight Mode 1.66 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage56 of 70...
<-50 23.5±1 WCDMA Band IV <-50 23.5±1 Band V <-50 23.5±1 Band 2 <-44 23.0±1 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage57 of 70...
In the application of the module, due to static electricity generated by human body static electricity, and charged The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage58 of 70...
10.1 Product appearance The SC806 module appearance is shown in the figure: Figure 19Module Product Appearance The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage59 of 70...
The structural dimension of the SC806 module is shown in the figure: Figure 20Structural Dimension The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage60 of 70...
Storage life (seal vacuum packaging): The Storage life is 12 months under the recommended storage conditions. The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage61 of 70...
10.6.1 Tray packaging The SC806 module is packaged in trays, 15 PCS per tray, 6 trays per box, 6 boxes per package. 1 tray of 10 PCS modules is at above, and 1 empty tray is at the bottom, a tray with a total of 8 PCS. The tray packaging is shown in the figure: The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval.
Page 63
Figure 22Tray Packaging The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage63 of 70...
10.6.2 Tray dimension The tray dimension is 315*170*6.5mm, as shown in the figure: Figure 23Tray Dimension The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage64 of 70...
Mobile Station Mobile Terminated Printed Circuit Board Protocol Data Unit Phase Shift Keying Quadrature Amplitude Modulation The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage65 of 70...
Page 66
Minimum Input High Level Voltage Value VILmax Maximum Input Low Level Voltage Value VILmin Minimum Input Low Level Voltage Value The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage66 of 70...
Page 67
Minimum Output Low Level Voltage Value VSWR Voltage Standing Wave Ratio WCDMA Wideband Code Division Multiple Access The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage67 of 70...
Radio Block excl.USF and BCS Tail Coded Bits Punctured Bits Data rate Kb/s 9.05 13.4 15.6 21.4 The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage68 of 70...
GPRS device can use for both uplink and downlink communications. Table45Multilevel multislot allocation Multislot Class Downlink Slots Uplink Slots Active Slots The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage69 of 70...
MCS-7 8-PSK 44.8kbps 89.6kbps 179.2kbps MCS-8 8-PSK 54.4kbps 108.8kbps 217.6kbps MCS-9 8-PSK 59.2kbps 118.4kbps 236.8kbps The copyright of this document is owned by Fibocom Wireless Inc., and the document shall not be replicated without approval. SC806Hardware User ManualPage70 of 70...