Warning Codes; Machine Lock-Up Error Codes - JCM GLOBAL VEGA-RC Twin Series Integration Manual

Error
LED Indication
Codes
35
x 7 Times
36
x 8 Times
NOTE: Dispensing performance from the VEGA-RC Twin will have an abnormal termination anytime a
Banknote remains on one of the sensors in the VEGA Unit. The Banknote being processed is counted as a
dispense completed Banknote.
NOTE: When a command from the host machine is being received or an electrical power failure occurs before
the dispensing process begins, the processing Banknote is counted as a dispense completed Banknote.
W C
ARNING ODES
When the following errors occur, they can be cleared automatically in five (5) seconds, but future perfor-
mance is not guaranteed. For this reason, replacing the CPU Board is recommended.
Error
LED Indication
Codes
98
x 5 Times
99
x 6 Times
M L - E
ACHINE OCK UP
When the following errors occur, the unit will stop operating.
Error LED
Codes Indication
The VEGA-RC Twin™ Upper Brushless Motor
01 is not moving - VEGA-RC Twin™ Motor
Lit
abnormality error.
The VEGA-RC Twin™ Lower Brushless Motor
02 is not moving - VEGA-RC Twin™ Motor
Lit
abnormality error.
Receive different denomination information
05
Lit
(money class) during communication.
VEGA™ Unit Motor abnormal error.
06 Motor encoder signal not received from
Lit
VEGA™ Unit.
07 Abnormal INHIBIT information.
Lit
Using a 24V DC Supply for a 12V DC
08
Lit
specification.
Using a 12V DC Supply for a 24V DC
09
Lit
specification.
EEPROM writing error - Failed to write data
10
Lit
into EEPROM normally.
The Brushless Motors for transport is not
16 moving - VEGA-RC Twin™ Motor abnormality
Lit
error.
VEGA's Flapper is ON when the VEGA-RC
17
Lit
Twin™ "initialization" process is over.
P/N 960-000169R_Rev. A {EDP #217859}
VEGA-RC Twin™ Series Banknote Recycler Integration Guide
Table 10 Operation Error Codes (Continued)
Possible Fault Causes
[Dispense/Retrieving error - lower] Banknote jam
occurs within the VEGA-RC Twin™ Unit.
[Dispense/Retrieving error - lower] Banknote jam
occurs at the VEGA™ insertion slot.
Table 11 Warning Codes
Possible Fault Causes
Program rewriting time is over limit (more than
1,000 occurrences).
[Warning issued for over limit program rewriting
because that is limited to 1,000 times.]
EEPROM malfunction.
Warning issued if an abnormal EEPROM
reading occurs.
C
RROR ODES
Table 12 Machine Lock Error Codes
Possible Fault Causes
Corrective Action Required
Verify there is not a Banknote jam, or an in-path
foreign object. Also, check that assemblies are
properly connected and/or harnessed, and all
unit sensors are clean. Recovery movement will
start after removing the jam.
Corrective Action Required
When program rewriting time has occurred over 1,000
times, this error code will appear for five (5) seconds
and every time thereafter.
Change the CPU Board. [When this occurs, EEPROM
data, such as the number of accepted Banknotes,
errors, the total number of errors, the operation log,
dispense times, and serial number will be lost.]
Corrective Action Required
Check that the assemblies are properly connected and/or
harnessed, and all of the unit's sensors are clean.
Check that the assemblies are properly connected and/or
harnessed, and all of the unit's sensors are clean.
Check that the VEGA-RC Twin™ stacking denomination
matches the VEGA™ limit's command denomination
(confirm that both denomination settings agree).
Check that the assemblies are properly connected and/or
harnessed, and all of the unit's sensors are clean.
The VEGA™ Unit's denomination setting for the VEGA-RC
Twin™ is INHIBITED. Check that the VEGA™ Unit's
denomination settings match the VEGA-RC Twin's
denomination settings.
Check that the working voltage is for the related Circuit
Board.
Check that the working voltage is for the related Circuit
Board.
Change the CPU Board.
Check that the assemblies are properly connected and/or
harnessed, and all of the unit's sensors are clean.
© 2012, Japan CashMachine Co., Limited
1 9