Veeder-Root TLS4/8601 Series Software/Hardware Upgrade & Replacement Manual
Hide thumbs
Also See for TLS4/8601 Series:
- Troubleshooting manual (43 pages) ,
- Installation manual (10 pages) ,
- Troubleshooting manual (10 pages)
Related Manuals for Veeder-Root TLS4/8601 Series
Summary of Contents for Veeder-Root TLS4/8601 Series
- Page 1 Manual No: 577014-043 ● Revision: C TLS4/8601 Series Consoles Software/Hardware Upgrade & Replacement Manual...
- Page 2 Customer Service will work with production facility to have the replacement product shipped as soon as possible. If “lost” equipment is delivered at a later date and is not needed, Veeder-Root will allow a Return to Stock without a restocking fee.
-
Page 3: Table Of Contents
Example Software Download Procedure..............18 System Snapshot (Menu>Software Maintenance>System Snapshot) ......19 Example System Snapshot Procedure..............19 Upgrade Features (Menu>Software Maintenance>Upgrade Features) ......20 Figures Figure 1. TLS4/8601 Series Console - Dimensions ..........4 Figure 2. Component Locations (Front Cover Removed) ........5 Figure 3. Component Locations Underside Of Display/CPU Board Ass’y. -
Page 4: Contractor Certification Requirements
This manual contains instructions for TLS4/8601 Series ATG hardware assembly replacement and software maintenance procedures. Contractor Certification Requirements Veeder-Root requires the following minimum training certifications for contractors who will install and setup the equipment discussed in this manual: Installer (Level 1) Certification: Contractors holding valid Installer Certification are approved to perform wiring and conduit routing;... -
Page 5: Tls4/8601 Kits
Introduction TLS4/8601 Kits WARNING This product is to be installed and operated in the highly combustible environment of a gasoline station where flammable liquids and explosive vapors may be present. ATTEMPTING TO SERVICE TANK MONITORS AND EQUIPMENT WITHOUT PROPER TRAINING CAN CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, RESULTING IN PERSONAL INJURY OR DEATH. - Page 6 Introduction TLS4/8601 Kits Table 1. Miscellaneous Upgrade/Replacement Kits Part No. 333530-017 CPU Board Replacement Kit With IFSF LON, No Screen (TLS4B, TLS-S1) 333530-018 CPU Board Replacement Kit With IFSF LON, With Touch Screen (TLS4B, TLS-S1) 330020-750 USIOM Board Replacement Kit, AC (TLS4, TLS4i, DL4) 330020-753 USIOM Board Replacement Kit, DC (TLS4B) 330020-752...
-
Page 7: Component Identification
SERIAL 2 ETH 3 USB 2 ETH 1 Figure 1. TLS4/8601 Series Console - Dimensions LEGEND FOR NUMBERED BOXES IN Figure 1 1. Power conduit knockout (1 top/1 bottom) 7. Communication ports - standard: Serial ports 1 (full handshaking) and 2 2. -
Page 8: Figure 2. Component Locations (Front Cover Removed)
Component Identification TLS4/8601 Kits P2 RS232 P1 RS232 P2 RS485 P1 RS485 Figure 2. Component Locations (Front Cover Removed) LEGEND FOR NUMBERED BOXES IN Figure 2 10.Optional Graphical User Interface (GUI) display (on non-display 1. AC or DC input power connector (as ordered) consoles, the GUI display is replaced with the Alarm Reset (Ack) 2. -
Page 9: Figure 3. Component Locations Underside Of Display/Cpu Board Ass'y
Component Identification TLS4/8601 Kits Tech Figure 3. Component Locations Underside Of Display/CPU Board Ass’y. LEGEND FOR NUMBERED BOXES IN Figure 3 1. J36 Mode Jumper (shown in Operating Mode Position) 5. Ack switch cable connector (J40) - Consoles without display only 2. -
Page 10: Figure 4. Component Locations Usiom Board
Component Identification TLS4/8601 Kits MAX. AC INPUT RATINGS 120/240 Vac, 2.0 A 0°C ≤ Ta ≤ 50°C FOR SUPPLY CONNECTION, USE WIRES RATED FOR AT LEAST 90°C. MAX. RELAY (SLO-BLO) CONTACT RATING RELAY 2 120/240 Vac, 5A 30 Vdc, 5A FUSE RATING, 5A RELAY 1 250 Vac TYPE T... -
Page 11: Component Replacement Procedures
Component Replacement Procedures In non-display consoles the Ack/CPU assembly is, except for the display screen itself, essentially the same as the Display/CPU assembly. The Display ribbon cable connects to a different CPU board connector than the Ack switch panel cable plug (see Items 4 and 5 in Figure 3). Other than the GUI display and Ack switch panel difference, the additional removal procedures discussed in this section are identical. -
Page 12: Replacing The Features Ibutton
Component Replacement Procedures Replacing The Features iButton Figure 5. Inserting SD Card In Its CPU board Enclosure LEGEND FOR NUMBERED BOXES IN Figure 4 1. Check the SD Card read/write slide position. 2. Insert the SD card into its enclosure with the contact side facing the CPU board. -
Page 13: Figure 6. Remove All Plugs Attached To Usiom Board
Component Replacement Procedures Replacing the USIOM Board 3. Remove all plugs connected to the USIOM board (identified by arrows in Figure 6). 4. Remove the two T15 #8 x 0.3125 screws securing the expansion comm port plate to the bottom of the console enclosure and set them aside with the comm plate. -
Page 14: Figure 7. Remove Two T15 Screws Securing Comm Plate
Component Replacement Procedures Replacing the USIOM Board CDIM 1 CDIM 2 SERIAL 1 EXPANSION ETH 2 USB 1 SERIAL 2 ETH 3 USB 2 ETH 1 Figure 7. Remove Two T15 Screws Securing Comm Plate MAX. AC INPUT RATINGS 120/240 Vac, 2.0 A 0°C ≤... -
Page 15: Figure 10. Remove Two T15 Screws Securing I.s. Cover
Component Replacement Procedures Replacing the USIOM Board MAX. AC INPUT RATINGS 120/240 Vac, 2.0 A 0°C ≤ Ta ≤ 50°C FOR SUPPLY CONNECTION, USE WIRES RATED FOR AT LEAST 90°C. MAX. RELAY (SLO-BLO) CONTACT RATING RELAY 2 120/240 Vac, 5A 30 Vdc, 5A FUSE RATING, 5A RELAY 1... -
Page 16: Software Maintenance And Upgrades
Software Maintenance and Upgrades The Main or Home screen is the primary entry to TLS4 software maintenance screens. Touch the Menu>Software Upgrade icons to view a list of the available Software Maintenance screens: Figure 12. Software Maintenance Screen Activate/Revert Screen (Menu>Software Maintenance>Activate/Revert) 0 Warning(s) System Status... -
Page 17: Notes On Reverting To A Previous Software Version
Software Maintenance and Upgrades Activate/Revert Screen (Menu>Software Maintenance>Activate/Revert) NOTES ON REVERTING TO A PREVIOUS SOFTWARE VERSION A copy of the previous (older) system software and databases is stored on the console SD card. If the current (newer) version of system software/features does not perform properly, the Revert operation gives you the ability to revert to the previous software version stored in the SD card. -
Page 18: Db Backup (Menu>Software Maintenance>Db Backup)
Software Maintenance and Upgrades DB Backup (Menu>Software Maintenance>DB Backup) DB Backup (Menu>Software Maintenance>DB Backup) System Status 0 Warning(s) 07/20/2013 09:10 AM 0 Alarms(s) Print (0) Software Maintenance DB Backup Home Current Version 1.gB 230.4 Available Version Not available Favorites Current Operations IDLE Backup Destination Select destination device... -
Page 19: Db Restore (Menu>Software Maintenance>Db Restore)
Software Maintenance and Upgrades DB Restore (Menu>Software Maintenance>DB Restore) 3. Select thumbdrive as the backup destination. Notice the Version field displays thumbdrive information. 4. Touch Backup button to begin the backup. 5. After completing the backup, the ‘Backup Completed Successfully!’ message appears. 6.Remove the thumbdrive and put it in a secure location. -
Page 20: Download (Menu>Software Maintenance>Download)
Software Maintenance and Upgrades Download (Menu>Software Maintenance>Download) Table 4. DB Restore Screen Field Descriptions Field Description Restore Starts the actual restore. Note: When you click Restore, a confirmation prompt displays, letting you know that the system will restart (reboot) to do the restore. If the system is not in use, touch the button to continue. -
Page 21: Example Software Download Procedure
Software Maintenance and Upgrades Download (Menu>Software Maintenance>Download) Table 5. Download Screen Field Descriptions Field Description Restore Starts the actual download. NOTE: When you click Download, a confirmation prompt displays, letting you know that the system will restart (reboot) to do the download. If the system is not in use, touch the button to continue. -
Page 22: System Snapshot (Menu>Software Maintenance>System Snapshot)
Software Maintenance and Upgrades System Snapshot (Menu>Software Maintenance>System Snapshot) System Snapshot (Menu>Software Maintenance>System Snapshot) 0 Warning(s) System Status 07/20/2013 09:10 AM 0 Alarms(s) Print (0) Software Maintenance System Snapshot Home Current Version 1.gB 230.4 Available Version Not available Favorites Current Operations IDLE Snapshot Destination Select destination device... -
Page 23: Upgrade Features (Menu>Software Maintenance>Upgrade Features)
Software Maintenance and Upgrades Upgrade Features (Menu>Software Maintenance>Upgrade Features) Upgrade Features (Menu>Software Maintenance>Upgrade Features) 0 Warning(s) System Status 07/20/2013 09:10 AM 0 Alarms(s) Software Maintenance Upgrade Features Print (0) Home Expansion box 3.0 GPH PLLD Favorites ATG Functionality Datalogger Functionality Menu Install features Actions... - Page 24 For technical support, sales or other assistance, please visit: www.veeder.com...