Transfer The Load From Maintenance Bypass To The Ups - Eaton 9355 User Manual

7. Wait for the front panel LCD to illuminate.
1. If an optional wall-mounted bypass cabinet is installed, proceed to
Step 2; otherwise, proceed to Step 4.
UPS Operating Instructions
The
2. Verify the wall mounted bypass is transfered to UPS mode (see
The UPS starts and transfers to Bypass mode. This may take up to
"Using the Wall-Mounted Bypass Cabinet" on page 97.
1 minute.
Normal Mode Startup
3. Proceed to Step 4.
The
To start up the UPS when the load is de-energized:
with the
The
4. Verify that the internal maintenance bypass switch is in the UPS
mode. The load is now powered by utility power.
1. If an optional wall-mounted bypass cabinet is installed, proceed to operating in Bypass mode.
position (see Figure 59 on page 95).
Normal Mode Startup
16. Switch the UPS input circuit breaker to the ON (
Step 2; otherwise, proceed to Step 4.
2. Switch the bypass breaker (may be designated MBP or CBP) in the wall-mounted bypass cabinet to the
The display indicates On Manual/Maintenance Bypass.
To start up the UPS when the load is de-energized:
5. If an optional isolation transformer is installed, switch the input
17. Wait for the UPS front panel display to illuminate.
ON position.
2. Verify the wall mounted bypass is transfered to UPS mode (see
circuit breaker to the ON position (see Figure 12 on page 21).
8. To switch to Normal mode from internal Bypass mode, transfer the
1. If an optional wall-mounted bypass cabinet is installed, proceed to
"Using the Wall-Mounted Bypass Cabinet" on page 97.
3. If present, switch the maintenance isolation breaker (MIS) on the wall-mounted bypass cabinet to the OFF
The
wall mounted bypass to Bypass mode (see "Using the
Step 2; otherwise, proceed to Step 4.
6. Switch on utility power where the UPS is connected.
position; otherwise, switch the UPS breakers (may be designated MOB or UPS) on the wall-mounted
Wall-Mounted Bypass Cabinet" on page 97 and rotate the internal
3. Proceed to Step 4.
bypass cabinet to the OFF position.
18. Check the UPS front panel display for active alarms or notices
2. Verify the wall mounted bypass is transfered to UPS mode (see
7. Wait for the front panel LCD to illuminate.
maintenance bypass switch to the UPS position.
(other than "Batteries Disconnected"). Resolve any active alarms
The UPS is now bypassed, with the load powered by utility power. "Using the Wall-Mounted Bypass Cabinet" on page 97.
4. Verify that the internal maintenance bypass switch is in the UPS
before continuing.
The
The
position (see Figure 59 on page 95).
To transfer the load from maintenance bypass to the UPS mode:
3. Proceed to Step 4.
mode. The load is now powered by UPS.
19. Switch the UPS battery circuit breaker to the ON (
8. Remove the breaker tie from all battery circuit breakers.
5. If an optional isolation transformer is installed, switch the input
1. If the UPS was powered off, continue to
4. Verify that the internal maintenance bypass switch is in the UPS
circuit breaker to the ON position (see Figure 12 on page 21).
20. If optional EBMs are installed, connect the EBM cable to the UPS
9. Switch all battery circuit breakers to the ON position.
position (see Figure 59 on page 95).
If the UPS is already in Bypass mode, proceed to
extended battery connector.
6. Switch on utility power where the UPS is connected.
2. Switch ON the utility power where the UPS is connected.
The
5. If an optional isolation transformer is installed, switch the input
The following table shows the indicator status and description.
Switch all EBM battery circuit breakers to the ON (
circuit breaker to the ON position (see Figure 12 on page 21).
7. Wait for the front panel LCD to illuminate.
3. Wait for the front panel LCD to illuminate.
10. Press any button on the front panel display to activate the menu
Description
21. Verify that the "Batteries Disconnected" alarm has cleared. Verify
options.
6. Switch on utility power where the UPS is connected.
The
The
that no other alarms appear on the UPS front panel display.
The UPS is operating normally.
11. Press the
7. Wait for the front panel LCD to illuminate.
8. Remove the breaker tie from all battery circuit breakers.
4. Switch all battery circuit breakers to the ON position.
If the
S The UPS is starting up or is shut down and waiting for power to return.
button to select the TURN UPS ON/OFF menu.
Removing the Existing Power Cords
clear. Check the UPS status from the front panel to view the active
The
S A new information message is active. 9. Switch all battery circuit breakers to the ON position.
The
alarms. Correct the alarms and restart if necessary.
12. Select the TURN UPS ON option. Press and hold the
S Bypass is not available.
8. Remove the breaker tie from all battery circuit breakers. The
The UPS starts and transfers to Bypass mode. This may take up to 1 minute. three seconds, until the UPS stops beeping.
The UPS is turned off and will not turn on automatically.
22. Press any button on the front panel display to activate the menu
9. Switch all battery circuit breakers to the ON position.
10. Press any button on the front panel display to activate the menu
options. Select TURN UPS ON/OFF, TURN UPS ON, and press the
The
The
The UPS is in Battery mode.
options.
the UPS is operating in Bypass mode.
The
If the
The display indicates On Manual/Maintenance Bypass.
11. Press the 23. Confirm the selection. Press and hold the
panel to view the active alarms. Correct the alarms and restart if
10. Press any button on the front panel display to activate the menu
The UPS is in Bypass mode. button to select the TURN UPS ON/OFF menu.
seconds, until the UPS stops beeping.
necessary.
5. Verify voltage is present on the UPS output by checking that an output voltage reading present on the front
options.
panel LCD display.
12. Select the TURN UPS ON option. Press and hold the Verify that the
11. Press the
The load is now powered by utility power. three seconds, until the UPS stops beeping.
UPS is operating normally and any loads not connected through the
The UPS has an active alarm.
button to select the TURN UPS ON/OFF menu.
Load Connector are now energized.
6. If present, switch the maintenance isolation breaker (MIS) on the wall-mounted bypass cabinet to the ON
The
There is a new UPS alarm condition. See "Troubleshooting" on page 105 for
position; otherwise, switch the UPS breakers (may be designated MOB or UPS) on the wall-mounted
12. Select the TURN UPS ON option. Press and hold the
If the
additional information.
bypass cabinet to the ON position.
three seconds, until the UPS stops beeping.
If the
clear. Check the UPS status from the front panel to view the active
panel to view the active alarms. Correct the alarms and restart if
alarms. Correct the alarms and restart if necessary.
7. Switch the bypass breaker (may be designated MBP or CBP) in the wall-mounted bypass cabinet to the
The
necessary.
OFF position.
Changing the Language
The UPS should be in Normal mode. By default, Normal mode
If the
The UPS is now powering the load in Bypass mode.
operates on the High Efficiency setting.
Press and hold the first button on the left for approximately five seconds
panel to view the active alarms. Correct the alarms and restart if
8. Transfer the UPS to Normal mode:
to select the language menu. This action is possible from any LCD menu
necessary.
24. To energize a load connected through the Load Connector, switch
screen.
• Press the
the load connector circuit breaker to the ON (
25. Press the
• Press the
Display Functions
The UPS is now powering the load in Normal mode.
As the default or after 15 minutes of inactivity, the LCD displays the
selectable startup screen. The default is the Eaton logo and can be
Eaton BladeUPS Cord Kit Instructions
7 7 . . 6 6 C C o o n n f f i i g g u u r r i i n n g g t t h h e e U U P P S S f f o o r r E E B B M M s s
changed to the Mimic screen in the User Settings menu.
To ensure maximum battery runtime, configure the UPS for the correct number of EBMs:
The backlit LCD automatically dims after a long period of inactivity. Press
any button to restore the screen.
1. Press any button on the front panel display to activate the menu options.
Use the two middle buttons ( and ) to scroll through the menu
2. Using the
structure. Press the button to enter a submenu. Press the
to select an option. Press the
previous menu.
96 Eaton 9355 UPS (10/15 kVA) User's Guide 164201594—Rev H0
S
164201594 Rev D
indicator flashes.
indicator flashes while transfering to bypass then goes out
illuminating to indicate the UPS is operating in Bypass
indicator illuminates and the
indicator flashes on the UPS.
indicator flashes.
indicator illuminates to indicate the UPS is operating in UPS
indicator stops flashing.
indicator flashes.
indicator flashes.
button on the front panel display and then press the
Eaton 9355 UPS (10/15 kVA) User's Guide
indicator is flashing, do not proceed until all alarms are
indicator flashes.
indicator stops flashing.
To remove the existing power cords:
indicator stops flashing.
1. If the UPS and internal batteries are already installed, continue to
indicator illuminates. The UPS is now powering the load.
indicator flashes while transferring to bypass then goes out with the
Step 2. If the UPS and internal batteries are not installed, continue
button.
to Step 15.
indicator stops flashing.
indicator is flashing, check the UPS status from the front
button on the front panel display and then press the
2. You MUST shut down the UPS before replacing the cord assembly.
Continue to Step 3 to shut down a standalone UPS.
indicator illuminates solid, indicating that the
For parallel shutdown procedures, refer to the Eaton BladeUPS
button on the front panel display and then press the
(12 kVA) User's Guide and then continue to Step 11.
indicator illuminates. The UPS is now powering the load.
3. Switch the load connector circuit breaker to the OFF (O) position
indicator is flashing, do not proceed until all alarms are
Eaton 9355 UPS (10/15 kVA) User's Guide
(see Figure 2).
indicator is flashing, check the UPS status from the front
indicator illuminates. The UPS is now powering the load.
NOTE The load connector breaker controls the load connector only, not the output power.
indicator is flashing, check the UPS status from the front
4. Press any button on the front panel display to activate the menu
options. Select TURN UPS ON/OFF, TURN UPS OFF, and press the
button.
button to select the Go To Normal Mode option.
Eaton 9355 UPS (10/15 kVA) User's Guide
5. Confirm the selection. Press and hold the
button until the Eaton logo appears.
ESC
button until the Eaton logo appears.
seconds, until the UPS stops beeping.
The output relays open, the UPS transfers to Standby mode, and
Eaton 9355 UPS (10/15 kVA) User's Guide
S
the indicator turns off.
6. Switch the UPS battery circuit breaker to the OFF (O) position.
7. If optional EBMs are installed, switch all EBM battery circuit
breakers to the OFF (O) position.
button, scroll to the Settings menu.
Disconnect the EBM cable from the UPS extended battery
ESC
button to cancel or return to the
connector.
8. Switch the UPS input circuit breaker to the OFF (O) position.
9. Switch off utility power where the UPS is connected.
10. Unplug the power cords.
10. Press any button on the front panel display to activate the menu
options.
OPERATION
11. Press the button on the front panel display and then press the
button to select the TURN UPS ON/OFF menu.
OPERATION
CORD KIT INSTRUCTIONS
12. Select the TURN UPS ON option. Press and hold the
three seconds, until the UPS stops beeping.
The indicator illuminates. The UPS is now powering the load.
indicator extinguishes, indicating the UPS system is
| ) position.
If the indicator is flashing, check the UPS status from the front
panel to view the active alarms. Correct the alarms and restart if
necessary.
Eaton 9355 UPS (10/15 kVA) User's Guide
| ) position.
Step 2.
Step 6.
| ) position.
S 164201594 Rev D
button for
button for three
button for
button for
S
164201594 Rev D
| ) position.
S 164201594 Rev D
S
164201594 Rev D
164201721 Rev 2 Draft 13-APR-2010
button
Internal Bypass Startup
To start the UPS when load is powered by internal bypa
1. If an optional wall-mounted bypass cabinet is insta
Step 2; otherwise, proceed to Step 4.
2. Verify the wall mounted bypass is transfered to By
"Using the Wall-Mounted Bypass Cabinet" on pag
3. Proceed to Step 4.
S
164201594 Rev D
4. Verify that the maintenance bypass switch is in the
position (see Figure 59 on page 95).
5. If an optional isolation transformer is installed, swit
circuit breaker to the ON position (see Figure 12 on
6. Switch on utility power where the UPS is connecte
CORD KIT INSTRUCTIONS
7. Wait for the front panel LCD to illuminate.
The indicator flashes.
89
The UPS starts and transfers to Bypass mode. This
1 minute.
The indicator flashes while transfering to bypa
with the illuminating to indicate the UPS is ope
illuminating to indicate
mode. The load is now powered by utility power.
The display indicates On Manual/Maintenance Byp
8. To switch to Normal mode from internal Bypass m
wall mounted bypass to Bypass mode (see "Using
Wall-Mounted Bypass Cabinet" on page 97 and rot
maintenance bypass switch to the UPS position.
The indicator illuminates to indicate the UPS is
87
mode. The load is now powered by UPS.
87
button for three
Eaton 9355 UPS (10/15 kVA) User's Guide
87
15
button for
87
S 16420159