Advertisement
9)
made later.
STEP 10
10)
When determining the door
mounting positioning, you
will first calculate the overlay
by measuring the door vs.
the cabinet opening. Refer to
Figure 10 for more direction.
NOTE: Overlay is the door
width minus the cabinet
opening width then dividing
by 2. For example, if a door is
D
12-1/2" wide, and the cabinet
D
opening is 12" wide:
12.5-12=1/2
1/2 divided by 2 = 1/4
The overlay = 1/4"
STEP 11
Now you are ready to hang
D
the door. Drive two #6 screws
D
into only the top two pilot
holes (See Fig 11A). Position
the door so the screws fit into
14)
the T-Type door mount bracket
(See Figure 11B). Make sure
the door is oriented correctly,
and using two #8 1/2" Wood
Screws, affix the bottom Door
Adjustment
Mount Bracket to the door and
tighten top screws
(See Figure 11C).
15)
#2
on the left. The reverse is true if you loosen the front screw and
g. 11
STEP 12
The first adjustment is the left
to right tilt. By tightening the
front screw and loosening the
back screw, the door will tilt
left. By loosening the front
screw and tightening the
back screw, the door will tilt
right. Once you have the door
adjusted correctly, tighten the
center screw both on top and
bottom. Now snap on the logo
cap to cover this hardware on
top (See Figure 12).
16)
11)
To calculate overlay measure the door and then measure the
11)
To calculate overlay measure the door and then measure the
12)
To determine dimensions for "A"
12)
Finding Measurement "A"
To determine dimensions for "A"
to install into the meat of the door to
Locate your stiles
(Note: Screws need to be
to install into the meat of the door to
installed into the thick portion of
your door to prevent splitting)
Adjust the top T-Type door
mount brackets so they will
hit the mounting screws in this
dimension
Finding Measurement "B"
13)
Lay your door on a flat surface
At this point, lay your door on a
and mark 6 or 8 pilot hole
13)
At this point, lay your door on a
locations based on Figure 10.
Dimension "B" for a face frame
cabinet is 4-1/4".
Use table to find dimensions "C" and "D"
Face Frame
5743
4-1/4" [108 mm]
5750
4-1/4" [108 mm]
5743
5758
4-1/4" [108 mm]
5750
5773
4-1/4" [108 mm]
5758
5773
FIGURE 11A
D
g. 11
D
INSTALLATION INSTRUCTIONS: 5700 SERIES PULLOUT PANTRY
D
D
5743
⁄ " drill
5750
5758
⁄ " drill
5773
Frameless
C
4" [102 mm]
N/A
Face Frame
Frameless
4" [102 mm]
20-7/8"[530 mm]
4-1/4" [108 mm]
4" [102 mm]
4" [102 mm]
20-7/8"[530 mm]
4-1/4" [108 mm]
4" [102 mm]
4" [102 mm]
20-7/8"[530 mm]
4-1/4" [108 mm]
4" [102 mm]
4-1/4" [108 mm]
4" [102 mm]
FIGURE 11B
g. 11
g. 12
FIGURE 12
11)
To calculate overlay measure the door and then measure the
-
-
FIGURE 10
12)
To determine dimensions for "A"
to install into the meat of the door to
A
A
D
D
13)
At this point, lay your door on a
B
B
⁄ " drill
Face Frame
Frameless
4-1/4" [108 mm]
4" [102 mm]
g. 9
4-1/4" [108 mm]
4" [102 mm]
g. 9
4-1/4" [108 mm]
4" [102 mm]
4-1/4" [108 mm]
4" [102 mm]
D
N/A
C
D
N/A
N/A
N/A
20-7/8"[530 mm]
20-7/8"[530 mm]
N/A
25 1/5" [640 mm]
20-7/8"[530 mm]
20-7/8"[530 mm]
20-7/8"[530 mm]
25 1/5" [640 mm]
D
g. 12
D
D
-
A
D
B
g. 9
C
D
N/A
N/A
20-7/8"[530 mm]
N/A
20-7/8"[530 mm]
20-7/8"[530 mm]
20-7/8"[530 mm]
25 1/5" [640 mm]
FIGURE 11C
g. 12
D
17)
The
5
Advertisement
