Advertisement
STEP 1
Attach the feet to the bottom
slide using six M4 screws (See
Fig 1). Attach the rear foot
by removing the soft-close
mechanism as shown in Figure
1. After attaching the rear
foot, reattach the soft-close
mechanism.
NOTE: You will need to
remove the inner member(s)
from the slide so you have
a hollow channel when
attaching the feet.
STEP 2
Place the bottom slide
template in the bottom of your
cabinet as shown in Figure
2A. Mark 12 hole locations as
shown on the template and
drill 1/8" pilot holes where
indicated. Align the front of the
slide with the front of the face
frame and center the slide in
the cabinet. Attach to the floor
using #8 1" Wood Screws (See
Fig 2B).
NOTE: When using the
template to align the pilot
holes, be sure to fold across
the dotted line on the front
of the template to wrap over
the face frame or front end
of the frameless cabinet. This
will keep your slide from
being installed too far back
into the cabinet.
STEP 3
The Top slide of the pantry
needs to be mounted flush
with the face frame. It will likely
be necessary to cut and attach
a spacer board as shown in
Figure 3.
2
C
#2
1
8
(A)
MEASURE FACE
FRAME WIDTH
Customer Service: 800-626-1126 | rev-a-shelf.com
FIGURE 1
C
FACE FRAME CABINETS
Install bottom slide
1)
Attach feet (#9) to bottom slide (C) using M4 screw (#8) as shown
in
. 1
o T
t a
a t
h c
h t
e
e r
r a
FIGURE 2A
to remove the inner member(s) from the slide so you have a hollow
channel when attaching the feet.
C
C
2)
Mark
12
hole locations and drill ⁄
(60)
front of the slide with the front of the face frame and center the slide
(25)
n i
h t
e
a c
b
n i
. t e
t A
a t
h c
o t
h t
e
template to align the pilot hole, be sure to fold across the dotted line
on the front of the template to wrap over the face frame or front end
FIGURE 2B
of the frameless cabinet. This will keep your slide from being installed
too far back into the cabinet. See
FIGURE 3
Insert pantry frame
5)
The bottom of the frame (A) sits on top of the bottom slide (C) as
shown in
. 5
U
e s
M
6
c s
A
AT LEAST 8"
(B)
(A)
CORRESPONDING SPACER
6)
Slide the top portion of the frame up so that the top slide is
BOARD DIMENSIONS
concealed but not touching the wood cabinet.
o f
o
, t
h t
e
o s
t f
c -
o l
e s
w
l i
n l
e e
d
o t
(60)
(190)
(60)
p "
t o l i
h
o
e l
. s
R
o
u
g
h
y l
(120)
using screws (#7). When using the
2.
(120)
(60)
(60)
(25)
(25)
(B)
MEASURE
CABINET
e r
w
# (
) 2
n a
d
w
a
h s
r e
# (
) 3
o t
a
t t
DEPTH
3
C
C
Install
3)
T
b
e
a f
e c
as sh
M
a
g i l
n
h t
e
4)
U
Roug
n a
d
step
(60)
(190)
(60)
(60)
(190)
(120)
(60)
(60)
(25)
c a
. h
Advertisement
