Table of Contents
Advertisement
Notices
© Keysight Technologies, Inc. 2013, 2014
No part of this manual may be reproduced in
any form or by any means (including electronic
storage and retrieval or translation into a for-
eign language) without prior agreement and
written consent from Keysight
Technologies, Inc. as governed by United
States and international copyright laws.
Manual Part Number
Y1299-90001
Edition
October 2014. Build 2014.10.29.1439
Sales and Technical Support
For product specific information and support,
and to obtain the latest software and doc-
umentation, refer to
www.keysight.com/find/pxi-mimo.
Worldwide contact information for repair and
service can be found at
www.keysight.com/find/assist.
Information on preventing damage to your Key-
sight equipment can be found at
www.keysight.com/find/tips.
Regulatory Compliance
This product has been designed and tested in
accordance with accepted industry standards,
and has been supplied in a safe condition. To
review the Declaration of Conformity, go to
http:/regulations.corporate.keysight.com
/DoC/search.htm.
Warranty
The material contained in this document
is provided "as is," and is subject to being
changed, without notice, in future edi-
tions. Further, to the maximum extent per-
mitted by applicable law, Keysight
disclaims all warranties, either express or
implied, with regard to this manual and
any information contained herein, includ-
ing but not limited to the implied war-
ranties of merchantability and fitness for
a particular purpose. Keysight shall not be
liable for errors or for incidental or con-
sequential damages in connection with
the furnishing, use, or performance of
this document or of any information
contained herein. Should Keysight and
the user have a separate written agree-
ment with warranty terms covering the
material in this document that conflict
with these terms, the warranty terms in
the separate agreement shall control.
Keysight Technologies does not warrant
third-party system-level (combination of
chassis, controllers, modules, etc.) per-
formance, safety, or regulatory com-
pliance, unless specifically stated.
Technology Licenses
The hardware and/or software described in this
document are furnished under a license and
may be used or copied only in accordance with
the terms of such license.
Restricted Rights Legend
If software is for use in the performance of a
U.S. Government prime contract or sub-
contract, Software is delivered and licensed as
"Commercial computer software" as defined in
DFAR 252.227-7014 (June 1995), or as a "com-
mercial item" as defined in FAR 2.101(a) or as
"Restricted computer software" as defined in
FAR 52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is sub-
ject to Keysight Technologies' standard com-
mercial license terms, and non-DOD
Departments and Agencies of the U.S. Govern-
ment will receive no greater than Restricted
Rights as defined in FAR 52.227-19(c)(1-2)
(June 1987). U.S. Government users will
receive no greater than Limited Rights as
defined in FAR 52.227-14 (June 1987) or DFAR
252.227-7015 (b)(2) (November 1995), as
applicable in any technical data.
Safety Notices
The following safety precautions should be
observed before using this product and any
associated instrumentation.
This product is intended for use by qualified
personnel who recognize shock hazards and
are familiar with the safety precautions
required to avoid possible injury. Read and fol-
low all installation, operation, and main-
tenance information carefully before using the
product.
If this product is not used as specified, the
protection provided by the equipment could
be impaired. This product must be used in a
normal condition (in which all means for pro-
tection are intact) only.
The types of product users are:
Responsible body is the individual or
n
group responsible for the use and
maintenance of equipment, for ensur-
ing that the equipment is operated
within its specifications and oper-
ating limits, and for ensuring oper-
ators are adequately trained.
Operators use the product for its
n
intended function. They must be
trained in electrical safety pro-
cedures and proper use of the instru-
ment. They must be protected from
electric shock and contact with haz-
ardous live circuits.
Maintenance personnel perform
n
routine procedures on the product to
keep it operating properly (for
example, setting the line voltage or
replacing consumable materials).
Maintenance procedures are
described in the user documentation.
The procedures explicitly state if the
operator may perform them. Other-
wise, they should be performed only
by service personnel.
Service personnel are trained to
n
work on live circuits, perform safe
installations, and repair products.
Only properly trained service per-
sonnel may perform installation and
service procedures.
Operator is responsible to maintain safe
operating conditions. To ensure safe oper-
ating conditions, modules should not be
operated beyond the full temperature range
specified in the Environmental and physical
specification. Exceeding safe operating con-
ditions can result in shorter lifespans,
improper module performance and user
Advertisement
Table of Contents
