Advertisement
Liberator
(9TB 72"/82")
This instruction contains 9 pages:
Page 1: Read Safety instructions
Page 2: Unpack and inspect parts contained
Page 3~4: Notes before installation and Hanging system installation
/Blade installation
Page 5: Wire connection
Page 6: Canopy installation / Remote Transmitter assembly
Page 7: Operational instruction / Troubleshooting
Page 8~9: Remote Pairing Process
Net weight
6.2 KGS.
13.6 LBS.
Toll Free: 1-855-676-7247
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
Advertisement
Table of Contents
Related Manuals for TroposAir Liberator
Summary of Contents for TroposAir Liberator
- Page 1 Liberator (9TB 72"/82") This instruction contains 9 pages: Page 1: Read Safety instructions Page 2: Unpack and inspect parts contained Page 3~4: Notes before installation and Hanging system installation /Blade installation Page 5: Wire connection Page 6: Canopy installation / Remote Transmitter assembly...
- Page 2 READ AND SAVE THESE INSTRUCTIONS WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING : 1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.
- Page 3 Unpack and inspect fan carefully to ensure all contents are included. Unpack (Fan & Blades packed Separately) Note: Hardware Bag Make sure you have received two boxes, one for fan and one for blades. For Mounting Bracket: Flat Washer Spring Washer Mounting Bracket Machine Screw x2 Wood Screw...
- Page 4 WARNING: BLADES SHOULD BE AT LEAST 7 FEET FROM FLOOR Note 1: Note 2: Use metal outlet box suitable Turn off power at breaker box to avoid possible for fan support. electrical shock. Outlet box must support 35 lbs min. OF F OF F OF 1.
-
Page 5: Blade Installation
Canopy Cross Pin Yoke cover Cotter Pin Downrod Jam Screws (2) (Tightening) Yoke Fan Assembly 2-5. Insert downrod assembly into yoke and attach the cross pin through yoke & downrod, secure with cotter pin. Fan Assembly 2-6. Tighten both downrod jam screws tosecure downrod. 2-4. -
Page 6: Wire Connection
5. WIRE CONNECTION 5-1. Verify that serial Number & Model Number match on the Receiver and Transmitter NOTICE: Many remote sets for DC fans look the same. This remote set is pre-paired and labeled at the factory, please note the following before operation: 1a. -
Page 7: Canopy Installation
6. CANOPY INSTALLATION Canopy 6-1. Canopy Align Holes Screw (2) 6-2. Key Hole (2) 6-4. Deco Ring Note: Two screws are installed on mounting bracket for canopy installation. 6-4. Push deco ring up to canopy, align holes on 6-1. Push up canopy until two pre-installed screws on mounting bracket are engaged with two key canopy with ribs on deco ring, and push “snap-in”. -
Page 8: Operational Instruction
(sold separately) JST connector Integrated type: For Titan II & Liberator & Elegant / Troposair TROUBLESHOOTING In the event the fan does not operate properly, please perform the following steps. 8-8. Lower the canopy and check that all wires are connected properly. - Page 9 9. REMOTE PAIRING PROCESS The Pairing Process is only necessary when there is an issue. Remote set is pre-paired from the factory and should not require the Pairing Process. A fan may need to have “Pairing Process” performed for the following issues. 1.
- Page 10 9-4. TO SET UP REMOTE FOR #2 FAN Make sure to turn off power at breaker box. Disconnecting wire from #1 Fan Disconnect the Black wires from #1 Fans and connect the Black wires back to #2 Fan that you remove from 9-3. Outlet Box Outlet Box (Disconnecting)
Need help?
Do you have a question about the Liberator and is the answer not in the manual?
Questions and answers