Chair E 1 and are therefore a must besides regular cleaning. ® Repair work and period tests may be carried out only by expert personnel authorised by ATMOS. By applying only original spare parts you will have the guarantee that operational safety, readiness for work and the value of your ATMOS Chair E 1 will be preserved.
Graphic symbols contained in these operating instructions Warning, special diligent notice ) Important information Symbols of ATMOS Chair E 1 ® Degree of protection type B Order number This product complies with the relevant requirements of EU Directive...
1.5 Scope of supply • Prior to dispatch, the ATMOS Chair E 1 was subjected to an extensive functional test and was carefully packed. ® Nevertheless, please compare the contents of the shipment on completeness immediately upon receipt (see delivery note).
• Please observe the ambient conditions stated in the described. technical data (chapter 9.0). • Please note: Chair E 1 is not designed for the use in • The ATMOS ® A medical insulating transformer with earth leakage medical areas with an explosion hazard. Explosion- monitor or any similar safety system acc.
3.0 Setting up and starting up 3.1 Assembly • Always place the device on a level, safe surface. 3.2 Starting up • Position the chair at the allocated space. Any floor unevenness must be compensated for. • Check that the upper part of the chair can rotate freely. •...
3.0 Setting up and starting up 3.3 Electrical connection The ATMOS Chair E 1 is supplied with a power cable and ® IEC connection. Insert the power cord to the IEC socket at the back side of the chair base and the wall mounted power outlet.
Down Furthermore, the ATMOS Chair E 1 features an “Auto – ® Down (homing)” function, driving the seat down to its lowest level after a short tap on the foot switch. Pressing the right foot switch for less than 0.5 seconds will move the chair to home position.
4.0 Operation 4.3 Rotating the upper part of the chair Upper part rotates around 360° via a ball bearing and is equipped with an arrestor each 90°. The upper part with the patient can then be rotated in the desired direction. ...
4.0 Operation 4.6 Adjusting the head rest The head rest (fig. 4) can be brought into a lower position by simply pulling the retaining strap into a lower position or by pushing it into a higher position. To remove the headrest, the retaining strap must be pulled out completely from the backrest.
• The surfaces of the ATMOS Chair E 1 are resistant against all the recommended surface disinfectants stated in chapter ® 5.3 and 5.4. Nevertheless after a longer period of use discolouration could occur. Polar solvents (e.g. acetone or chlorinated hydrocarbons (CCs)) may not be used for cleaning and disinfecting.
5.0 Cleaning and care 5.3 Recommended surface disinfectants • The surfaces of the ATMOS Chair E 1 can be cleaned / wiped with disinfectants containing the following active ingredients: ® - QAV (quarternary ammonium compounds) 5.4 Recommended disinfectants for the upholstery...
• Check main fuse • Check mains plug on perfect fit at the device • Defect fuse • Exchange of fuse Should a malfunction still occur, please inform the authorized ATMOS customer service immediately. 8.0 Accessories and spare parts 8.1 Accessories Child seat On request 8.2 Spare parts...
9.0 Technical data Voltage 230 V~ ± 10 %; 50/60 Hz Special voltage 120 V~ ± 10 %; 50/60 Hz Current consumption Max. 2.5 A Power consumption 520 VA Fuses T 3.15 A / 250 V Operating time 1.5 min operation / 8.5 min rest period Seating surface L x W 500 x 470 mm Seat height...
10.0 Disposal • The ATMOS Chair E 1 does not contain any hazardous materials. ® • The housing is recyclable. • Device and accessories must be decontaminated prior to disposal. • Pay attention to a careful separation of the different materials.
11.1 Guidelines and Manufacturer´s Declaration - Emissions The ATMOS Chair E 1 is intended for use in the electromagnetic environment specified below. The customer or user of the ® ATMOS Chair E 1 should ensure that it is used in such an environment.
Page 18
11.3 Guidelines and Manufacturer's Declaration - Immunity The ATMOS Chair E 1 is intended for use in the electromagnetic environment specified below. The customer or user of the ® ATMOS Chair E 1 should ensure that it is used in such an environment.
Page 19
Chair E 1 ® The ATMOS Chair E 1 is intended for use in electromagnetic environment in which radiated disturbances are controlled. The ® customer or user of the ATMOS Chair E 1 can help prevent electromagnetic interference by maintaining a minimum distance ®...