EWM drive 4X IC D HP Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.4.6
5.4.7
5.4.8
5.4.9
5.4.10
5.4.11
5.4.12
5.4.13
5.4.14
5.4.15
5.5 TIG welding .................................................................................................................................. 65
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.6 MMA welding ................................................................................................................................ 72
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.7 Remote control ............................................................................................................................. 74
5.8 Interfaces for automation ............................................................................................................. 74
5.8.1
5.9 Access control .............................................................................................................................. 75
5.10 Special parameters (advanced settings) ...................................................................................... 75
5.10.1
5.10.2
5.10.3
4
5.4.5.1 Setting the operating point (welding output).................................................. 38
5.4.5.2 Welding power (operating point) ................................................................... 39
5.4.5.3 Operating point setting via welding current, material thickness or wire
feed speed ..................................................................................................... 39
5.4.5.4 Arc length ...................................................................................................... 39
5.4.5.5 Accessory components for operating point setting ....................................... 39
coldArc / coldArc puls ................................................................................................... 40
forceArc / forceArc puls ................................................................................................ 40
rootArc/rootArc puls ...................................................................................................... 41
pipeSolution .................................................................................................................. 41
Operating modes (functional sequences) ..................................................................... 42
5.4.10.1 Explanation of signs and functions ................................................................ 42
5.4.10.2 Automatic cut-out .......................................................................................... 42
MIG/MAG program sequence ("Program steps" mode) ............................................... 55
5.4.11.1 Selection of the program sequence parameter ............................................. 55
5.4.11.2 MIG/MAG overview of parameters ................................................................ 56
5.4.11.3 Example, tack welding (non-latched) ............................................................ 56
5.4.11.4 Example, aluminium tack welding (non-latched special) .............................. 57
5.4.11.5 Example, aluminium welding (latched special) ............................................. 58
5.4.11.6 Example, visible seams (latched super pulse) .............................................. 59
Main program A mode .................................................................................................. 60
5.4.12.1 Selecting parameters (program A) ................................................................ 61
Standard MIG/MAG torch ............................................................................................. 62
MIG/MAG special-torches............................................................................................. 62
5.4.14.1 Program and up/down operation ................................................................... 62
5.4.14.2 Switching between Push/Pull and intermediate drive ................................... 62
Expert menu (MIG/MAG) .............................................................................................. 63
5.4.15.1 Selection ........................................................................................................ 63
5.4.15.2 Burn-back ...................................................................................................... 64
5.4.15.3 Programme limit ............................................................................................ 65
Welding torch connection ............................................................................................. 65
Welding task selection .................................................................................................. 66
5.5.2.1 Welding current setting .................................................................................. 66
TIG arc ignition ............................................................................................................. 67
5.5.3.1 Liftarc ............................................................................................................. 67
Operating modes (functional sequences) ..................................................................... 68
5.5.4.1 Explanation of signs and functions ................................................................ 68
5.5.4.2 Automatic cut-out .......................................................................................... 68
TIG program sequence ("Program steps" mode) ......................................................... 72
Welding task selection .................................................................................................. 72
5.6.1.1 Welding current setting .................................................................................. 73
Arcforce......................................................................................................................... 73
Hotstart ......................................................................................................................... 73
Antistick......................................................................................................................... 73
Parameter overview ...................................................................................................... 74
Remote control connection socket, 19-pole ................................................................. 75
Selecting, changing and saving parameters................................................................. 76
Reset to factory settings ............................................................................................... 78
Special parameters in detail ......................................................................................... 78
5.10.3.1 Ramp time for wire inching (P1) .................................................................... 78
5.10.3.2 Program "0", releasing the program block (P2) ............................................. 78
5.10.3.3 Display mode for Up/Down welding torch with one-digit 7-segment
display (P3) ................................................................................................... 79
5.10.3.4 Program limit (P4) ......................................................................................... 79
099-005507-EW501
13.09.2018