Auerswald COMpact 5010 VoIP Installation And Commissioning Instructions page 8

Important Information
Analogue answering machine
Modem
a/b door terminal system
Important: Devices using pulse dialling cannot use
the full range of features.
Important: Devices using dual-tone multi-frequency
dialling must be equipped with a flash button.
Note: When using a T-Net-capable analogue tele-
phone, most T-Net functions can be used via the exis-
ting function keys on the telephone.
Switching relay
A switching relay (not a part of the basic assembly basic
design) is suitable for connecting or controlling the follo-
wing devices:
Door terminal system according to FTZ 123 D12-0
(for example, TFS-Dialog 100, TFS-Dialog or TFS-
Dialog pro from Auerswald)
Door opener
Various devices to be switched (for example,
alarm sirens)
Important: The module supplies no switching vol-
tage to the relay contacts, meaning the devices to be
switched must be supplied with external voltage.
Attention: The relay contacts can handle a maxi-
mum load of 30 V/1 A (therefore, not suitable for a
direct connection to 230 V system voltage).
For switching devices operated on voltage, you
therefore need an additional load-switching relay
that is compatible with the safety regulations.
Ringer/alarm input
A ringer/alarm input (not a part of the basic assembly) is
suitable for connecting or controlling the following
devices:
Door bell button
Output devices for announcement, alarm and
monitoring signals (for example, leak warning
device)
Music input/audio output
A music input/audio output (not a part of the basic assem-
bly) is suitable for connecting or controlling the following
devices:
Loudspeaker unit
Active loudspeaker
Music output devices (for example, MP3 or CD
players)
USB Host
The USB host is suitable for connecting a USB printer for
call data printouts.
8
Basic assembly
The basic assembly on both PBXs includes the following
connection options:
1 port, switchable between S
and U internal
P0
1 port, switchable between S
nal
6 (COMpact 5010 VoIP) or 10 (COMpact 5020
VoIP) internal analogue ports
1 Ethernet interface for administration and internal
IP and Internet telephony over two VoIP channels
(SIP-compliant according to RFC 3261, VoIP
Codec G.711 µ-Law/a-Law)
1 USB host for printer
Hardware Extensions
Both PBXs have a module slot for the following module:
COMpact 2VoIP module – use this to extend the
PBX with a total of four external VoIP channels as
well as with the VoIP Codecs G.723.1, G.726,
G.729A/E and iLBC.
COMpact 2VoIP module (only for the COMpact
5020 VoIP) – use this to extend the PBX with a
total of eight external VoIP channels as well as
with the VoIP Codecs G.723.1, G.726, G.729A/E
and iLBC.
Important: To support the COMpact 6VoIP module,
the PBX needs firmware version 3.0.
The COMpact 5010 VoIP has a variable module slot and
the COMpact 5020 VoIP has three variable module slots
for the following modules:
COMpact POTS module – for extending the PBX
with an external analogue port.
COMpact 2POTS module – for extending the PBX
with two external analogue ports.
COMpact TSM module – for extending the PBX
with three switching relays, two ringer/alarm inputs
and a music input/audio output.
COMpact 2ISDN module (only for the COMpact
5020 VoIP) – for extending the PBX with two port,
separately switchable, between S
internal and U internal.
P0
Note: Switching between the internal and external
operating modes of the S
jumpers.
Note: Using the configuration manager, any number
of available VoIP channels can be reserved for
internal and external calls.
Software Extensions
When the PBX is enabled in an Upgrade Centre, various
extensions and other features can be activated .
Note: The system dongle required for the extension
is a component part of the basic unit.
You can extend the PBX with the following functions:
external, S internal
0 0
external, U inter-
0 P0
external, S
0 0
ports is done using
0