Table of Contents
Advertisement
Quick Links
Installation Instructions
SPS 800 / 1200 - Sliding Panel System
Plasma Advance
Design Highlights
-Range of Single Panel and Split Panel Options
-Space Efficient Design
-Wide Range of Cabinetry and Wall Design Options
-Unique Functionality
Thank you for choosing
futureautomation
email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565
ISSUE 008
Advertisement
Table of Contents
Related Manuals for Future Automation SPS 800
Summary of Contents for Future Automation SPS 800
- Page 1 Installation Instructions SPS 800 / 1200 - Sliding Panel System Plasma Advance Design Highlights -Range of Single Panel and Split Panel Options -Space Efficient Design -Wide Range of Cabinetry and Wall Design Options -Unique Functionality Thank you for choosing futureautomation email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565...
-
Page 2: Safety Information
Exceeding the weight capacity can result in serious personal injury or damage to equipment. Future Sound & Vision trading as Future Automation intend to make this and all documentation as accurate as possible. However, Future Automation makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. -
Page 3: Table Of Contents
SPS 800 / 1200 - Sliding Panel System Plasma Advance Contents Page Introduction Safety Information Contents Contents Tool Indicator Icons Installation Parts List Package Contents Stage 1 Before you Begin 1 Preliminary Checks Stage 2 Before you Begin 2 Electrical Connections... -
Page 4: Contents
Any damage to products during transit that is not checked and notified as “unchecked” or “damaged” upon receipt of delivery. Any part of your system that needs to be replaced during a warranty repair becomes the property of Future Automation. -
Page 5: Parts List
SPS 800 / 1200 - Sliding Panel System Plasma Advance Nuts & Bolts Multipack: Package Contents A range of nuts, bolts, washers and spacers to help add in the mounting for your screen 1 - Panel Mechanism Right 2 - Panel Mechanism Left... -
Page 6: Preliminary Checks
SPS 800 / 1200 - Sliding Panel System Plasma Ad- NOTE: Panel Advance Shaft rotates 180 degrees Before You Begin 1 to create a forward-back motion of 40mm. Preliminary Checks If out of sync by 180 degrees it may jam. -
Page 7: Before You Begin 2
Before You Begin 2 Electrical Connections The SPS 800 / 1200 mechanism must be connected to both the AC1, 2, 3 and DC1, 2 connection blocks. All connections must be made for the mechanism to fully function It is VERY important that when all... -
Page 8: Mark The Screen Position In The Enclosure
SPS 800 / 1200 - Sliding Panel System Plasma Ad- Mark The Screen Position In The Enclosure Firstly, mark where you intend the top of the plasma screen to be on the back wall of the enclosure. Then mark a line showing where the centre of the screen / opening will be. -
Page 9: Positioning The Moving Panel Mechanism
SPS 800 / 1200 - Sliding Panel System Plasma Advance Positioning The Moving Panel Mechanism Before the mechanisms can be fitted, it is important to decide on the exact positions where they need to be. Make sure that you have the mechanisms in the down and in position at this point. -
Page 10: Fitting The Moving Panel Mechanism
SPS 800 / 1200 - Sliding Panel System Plasma Ad- Fitting The Moving Panel Mechanism Before fixing the mechanisms, it is a good idea to cut a piece of wood to the size that you have just measured to provide the correct height. You can then sit both the mechanisms on the block of wood, knowing they are both at the correct height, alternatively 2 screws can be used. -
Page 11: Fitting The Drive Unit
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fitting The Drive Unit It is important that at this point both moving panel mechanism are in the same down and in position. The drive unit is a telescopic piece of equipment. -
Page 12: Fit The Ps Bracket To The Back Of The Screen
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fit the PS Bracket to the Back of the Screen Measure the distance from the top of the screen down to the centres of the two largest mounting holes in the PS Bracket wall plate. -
Page 13: Fitting The Ps Bracket To The Wall
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fitting the PS Bracket to the Wall Mark a line across the back of the enclosure that marks out the vertical position of the largest set of holes on the wall plate. -
Page 14: Fitting The Plasma Advance Unit
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fitting the Plasma Advance Unit Firstly, bolt the two side runners on to the sides of the PS bracket so that the arms of the Plasma Advance Unit can slide up and down the channels. -
Page 15: Connecting The Mechanism
SPS 800 / 1200 - Sliding Panel System Plasma Advance Connecting the Mechanism To connect the three mechanisms together electrically, is very simple. Each mechanism has a set of wires coming from it. On the ends of the wires are control box inserts and block connectors. -
Page 16: Fit The Mount Plate
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fit the Panel Mount Plates The mounting plates fix to the runners with M6 x 10mm CSK bolts with washers. There are a choice of 3 heights to fix the bolts on to. The large slot also allow for a lot of adjustability. -
Page 17: Fit The Front Panel And Moving Panel
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fit the Front Panel and Moving Panel Mounting Plate BACK PANEL Height -5mm (Clearance) Fix the front panel to the enclosure. Measure the height of the panel mounting plates from the bottom of the opening. -
Page 18: Fitting The Screen
SPS 800 / 1200 - Sliding Panel System Plasma Advance Fitting the Screen In order to fit the screen, the mechanism must be extended to its full reach. Press ‘OUT’ on the remote control and wait for the Plasma Advance mechanism to reach its pre-set out position. -
Page 19: Contact Closure
SPS 800 / 1200 - Sliding Panel System Plasma Advance Contact Closure - Use an RJ45 connector in the CCI socket on the control box to operate via contact closure WIRE / CABLE CONTACT CLOSURE DESCRIPTION ACTION 568A 568B LED INDICATOR... -
Page 20: Rs232
SPS 800 / 1200 - Sliding Panel System Plasma Advance RS232 - Use an RJ25 connector in the socket marked RS232 on the control box to operate using RS232 Pin 1: RX Pin 6 : TX Pin 2: TX Pin 3 & 4: GROUND... -
Page 21: Ir Control
SPS 800 / 1200 - Sliding Panel System Plasma Advance Operation buttons for the IR remote Note Only buttons indicated are functional with the product. Any button pressed when in motion mechanism will stop. IN - Screen moves back OUT - Panel moves in... -
Page 23: Notes
SPS 800 / 1200 - Sliding Panel System Plasma Advance Notes... Page 22 of 22 // email info@futureautomation.co.uk tel: +44 (0) 1438 833577 fax: +44 (0) 1438 833565... - Page 24 Future Automation Unit 2 Kimpton Enterprise Park Claggy Road Kimpton Hertfordshire SG4 8HP United Kingdom Tel: +44 (0) 1438 833 577 Fax: +44 (0) 1438 833 565 Email: info@futureautomation.co.uk www.futureautomation.co.uk...