Advertisement
Quick Links
"Turn-A-Tot" child restraint
The revolving carseat* with in built stabilising rebound section
A super compact seat for most small cars.
8
3
Turn-A-Tot Compact
The difference could save you a serious injury.
3
8
Some other seat
INSTRUCTIONS FOR INSTALLATION AND USE
CHECK THAT THIS CHILD RESTRAINT WILL FIT TO YOUR CAR
• Newborn to 18kgs.
• The Turn-A-Tot feature (rearward facing)
- Saves your back from injury when placing
baby in car seat.
- Easier to buckle up the harness with it
facing you.
- Safer for baby. As harness is in full view,
you can ensure it is properly fitted.
• An independent latching buckle system.
AUSTRALIAN SERVICE AGENT
*
Advertisement
Related Manuals for Infasecure Turn-A-Tot
Summary of Contents for Infasecure Turn-A-Tot
- Page 1 “Turn-A-Tot” child restraint The revolving carseat* with in built stabilising rebound section • Newborn to 18kgs. • The Turn-A-Tot feature (rearward facing) - Saves your back from injury when placing baby in car seat. - Easier to buckle up the harness with it facing you.
-
Page 2: Care And Maintenance
AUSTRALIAN SERVICE AGENT 110 - 114 old bathurst road, emu plains. nsw 2570 (02) 4728 8090 CONTENTS care instructions ...........................page 1& 9 cover removal ............................page 9 harness replacement and fitting ......................page 9 & 10 how to install child position (8 - 18kg) ....................page 6 & 7 how to install infant position (0 - 9kg) ....................page 3 &... - Page 3 hOW TO INSTALL ANChORAGE FITTINGS FOR vEhICLES FITTED WITh ANChORAGE POINTS. This resTrainT musT be aTTached To a child resTrainT anchorage poinT in The car. refer To car owner’s handbook for locaTion of ancorage poinTs. refer To a child resTrainT fiTTing sTaTion if no anchorage poinTs are in The moTor car.
- Page 4 (as in figure 3a), push down the ‘Turn-a-Tot’ lever located at the front of the base and swivel the body section through 180º so it faces the rear of the vehicle (see figure 3b and 3c).
- Page 7 HOW TO INSTALL : CHILD POSITION (8-18kg) FORWARD FACING MODE FIGURE 8 sTep 1 move the upper anchorage strap (b) from the front position used for the rearward facing mode to the rear of the seat. (see figure 8). normally it will be necessary to shorten the length of the upper anchorage strap when changing from rearward to forward facing mode.
- Page 8 HOW TO INSTALL CHILD POSITION (8-18kg) FORWARD sTep 4 extend the adultlap or lap/sash belt (as shown in figure12a). holding the vehicle belt (as shown in figure 12a) (note the position of the hands) loop it over the arm of the base section (position a in figure...
- Page 9 SHOULDER...
-
Page 10: To Remove Cover
CARE OF THE RESTRAINT TO REMOVE COVER STEP 1 Do Steps 1 to 3 from “to change the shoulder slot height” on page 8. STEP 2 Disengage the buckle and tongues. Push the buckle through the crotch slot in the cover. Pull the cover up and through the shoulder strap webbing and buckle tongues. - Page 11 TO REPLACE THE HARNESS STEP 1 Place one end of the harness through the SHOULDER required shoulder slot hole (See Arrow 1 in Fig. 18) then up and over the shoulder rod (See Arrow 2 in Fig. 18) and connect to the metal spreader plate by passing the webbing through the “gate”...
- Page 12 SASH SECTION REMAINS Installation of the Double “T” fitting LOOSE IF A RETRACTOR SEAT BELT FOR USE WITH LAP/SASH VEHICLE SEAT BELTS - IN BOTH REARWARD AND FORWARD MODES. PULL SASH SECTION TO INSTALL Once adult lap/sash seat belt is positioned through restraint TIGHT IN THIS base (refer installation instructions)
Need help?
Do you have a question about the Turn-A-Tot and is the answer not in the manual?
Questions and answers