i3 International A 65W Series Quick Start Manual

3MP Infrared Outdoor IP Dome Camera w/ White Light
Thank you for purchasing i3 International's Annexxus 65W indoor/outdoor 3MP IP dome
camera with built-in white light. Your camera is equipped with a motorized vari-focal
3-10.5mm lens. The lens can be controlled through camera's Web Interface in Internet
Explorer, through SRX-Pro Server/Remote or through Video Pilot Client. Built-in white light
settings can be configured only through camera's Web Interface in Internet Explorer.
SAFETY
When installing your Ax65W camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -40° C (-40° F) and above 50° C (122° F).
POWER
This camera accepts AC24V and PoE+ power. Maximum power consumption: 25W.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finish.
SERVICING
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the
camera. Refer servicing to qualified personnel only.

PACKAGE CONTENTS

Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
A. Standard RJ45 Connector x2
B. Round Head Screw (Tapping Type) w/ O-ring x4
C. Plastic Anchor x4
D. Surface Mount template x1
E. Flush Mount template x1
F. Security torx bit x1
G. Long Machine type screws x3
(for Flush Mounting with back box installations)
Lens Direction
GUIDE PATTERN
GUIDE PATTERN
Cut Line
D
Camera Outline
Scan this QR code or visit ftp.i3international.com to view and
download the full User Manual for this camera. Also available for
download is the AnnexxusConfigurationTool or ACT program
used to locate and configure your cameras with your SRX-Pro
software. This program is already installed in SRX-Pro v3.3.3.69
and higher. Please contact our Technical Support team if you have
any questions or concerns regarding camera installation or you
require software services or support. Technical support can be
reached by email at: support@i3International.com or by
phone toll free 1.877.877.7241.
i3-TRNG-CAMS-Ax65W-QSG.indd
A B C
G
F
E
QR Code to Complete
User Manual / ACT

Quick Start Guide

CAMERA PARTS AND DEFINITIONS

84 mm (3.3")
63 mm (2.5")
9
9
10 11
1. Back box. Camera's back box comes with six (6) 90% pre-drilled hole dimples.
For surface mounting, complete drilling a minimum of two (2) holes.
2. Camera module / second housing.
3. Tilt bracket with locking screw
4. Inner liner / Shroud. Inner liner is attached to the camera module but can be
partially detached for easier lens adjustment.
5. IR board
6. Screws securing the dome bubble housing to camera module (x3, silver)
7. Dome bubble housing / Dome cover
8. Lexan bubble
9. 3/4" waterproof rubber plug. For best waterproof performance, use a network
cable 5mm or more in diameter. To maintain IP67 waterproof rating, use sealant
on the threads during installation. If using the side conduit hole, replace the
rubber plug with the metal plug from the side conduit.
10. 3/4" side conduit hole with metal plug. If using the side conduit hole, remove
the metal plug and use it instead of the rubber plug in the top conduit hole. To
maintain IP67 waterproof rating, use sealant on the threads during installation.
11. Six (6) 90% pre-drilled hole dimples. Complete drilling a minimum of two (2) for
surface mounting.
12. Reset/Default pin-hole button. Press for 1 second to reboot the camera.
Press for 6 seconds to restore camera settings to factory defaults.
13. Micro SD Card slot for on-camera video storage. (microSD card sold separately)
14. Mini USB port. Manufacturer use only .
15. Screws attaching camera module to the back box (x3, silver)
16. Screws to engage locking arms (x2, black)
Ax65W
147 mm (5¾")
1
2
12
3
4
5
15
16
13
15
14
Rev.
6
7
8
15
16
190912