Specifications - Hitachi WM 10DBL Handling Instructions Manual

CAUTION
1. If liquid leaking from the battery gets into your eyes, do not
rub your eyes and wash them well with fresh clean water
such as tap water and contact a doctor immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you fi nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the fi rst time, do not use and return it to your
supplier or vendor.

SPECIFICATIONS

Although this machine includes 20 operation modes, up to four of them can be switched using the mode selection switch.
Four modes that are suitable for commonly performed operations have been set as factory default operation mode. With an
optional communication adaptor, you can freely select your desired operation modes. For details, refer to "Mode selection
and rewriting functions" on page 10.
POWER TOOL
Model
Battery type
Electronic pulse mode
Bolt mode
Self drilling screw mode
Capacity *1
Drill mode
Electronic clutch
mode *2
Electronic pulse mode
Tightening torque
Bolt mode [Tightening time: 3 sec.]
(Maximum)
[when fully charged
Self drilling screw mode
at 20°C temp]
Drill mode
Electronic clutch mode *2
Edge shape
Type of motor
Electronic pulse mode
Bolt mode
No-load speed
[when fully charged Self drilling screw mode
at 20°C temp]
Drill mode
Electronic clutch mode *2
Electronic pulse mode
Number of blows
[when fully charged Bolt mode
at 20°C temp]
Self drilling screw mode
Rechargeable battery
Dimensions of the tool
Entire length × height × center height
Weight
LED light
*1: The machine capability of BCL1015 becomes lower than that of BCL1030M in a high-load operation, because both
machines are of the same battery voltage but diff er in internal structure.
*2: The Electronic clutch mode is not of the factory default operation mode.
WARNING
If an electrically conductive foreign object enters the terminals
of the lithium ion battery, a short-circuit may occur resulting
in the risk of fi re. Please observe the following matters when
storing the battery.
○ Do not place electrically conductive cuttings, nails,
steel wire, copper wire or other wire in the storage
case.
○ Either install the battery in the power tool or store
by securely pressing into the battery cover until the
ventilation holes are concealed to prevent short-
circuits (See Fig. 1).
Wood screw
Ordinary bolt
High-strength bolt
Small drilling screw
Woodwork drilling
Steel drilling
Mortar drilling
Small screw
1.6 N·m {16 kgf·cm}
BCL1015: Li-ion 10.8 V
139 mm × 216 mm × 29 mm
(BCL1015 attached)
1.0 kg (BCL1015 attached)
WM10DBL
BCL1015
ø3.8 × 50 mm
M4 – M8
M4 – M6
ø5
ø12
ø5
ø6
M6
19 N·m {194 kgf·cm}
20 N·m {204 kgf·cm}
[Tightening is M8 high-strength bolt
(strength grade 12.9) Hexagon socket used]
14 N·m {143 kgf·cm}
10-point clutch 1 – 6 N·m {10 – 61 kgf·cm}
Width across fl at 6.35, bit insertion shape
DC motor
0 – 2200 /min
0 – 1300 /min
0 – 2200 /min
0 – 2200 /min
0 – 1140 /min
0 – 1090 /min
0 – 1030 /min
0 – 1090 /min
(1.5 Ah, 3 cells)
1.2 kg (BCL1030M attached)
White LED
BCL1030M
2.5 N·m {25 kgf·cm}
BCL1030M: Li-ion 10.8 V
(3.0 Ah, 6 cells)
139 mm × 233 mm × 29 mm
(BCL1030M attached)
7