Step 8. Installing Logs - Superior SSDVT-4035CNM Installation Instructions Manual

Electronic Appliance Checkout
To light the burner, turn 'ON' the optional remote
wall switch and turn the gas control switch to
the "ON" position. Ensure the Igniter lights the
pilot. The pilot fl ame should engulf the fl ame
rod as shown in Figure 51.
ELECTRONIC PILOT ASSEMBLY
Proper Pilot Flame Appearance
Proper Flame
Adjustment
Pilot
Nozzels
Figure 51
Step 8. INSTALL VOLCANIC STONE,
GLOWING EMBERS AND LOGS
1. Remove the front glass enclosure panel
(see Removing Glass Enclosure Panels on
Page 31).
2. Carefully remove the log set box from
the fi rebox. Next, remove embers and
volcanic stone from the control compart-
ment. Handle logs carefully to prevent
breakage.
3. Install Decorative Volcanic Stone - Mound
up a portion of the volcanic stone in front
of the burner in a pleasing pattern.
4. Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see Figure 52).
Keep the pieces fl uffed up, not matted.
Distribute these pieces over the surface of
the burner, as shown in Figures 53 & 54.
Do not use more than is necessary. Ensure
that the main burner slots remain uncovered
by the ember material.
Note: This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time. For
best glowing effect, replace the ember material
annually.
5. Placement of Logs -
The logs have locating notches or slots to
help ensure that they are properly positioned.
Proper log placement is critical to prevent
sooting.
28
SSDV-3530 - Install as Follows
Carefully position the ceramic fi ber logs into the
fi rebox as shown in Figure 53. Logs should be
placed in the order shown and per the following
instructions.
1. Place embers on the front burner tube and
volcanic stone in front of the burner as
shown and per instructions on this Page
(see Placement of Glowing Embers & Install
Decorative Volcanic Stone on this Page).
2. Place the rear log (A) as shown. Position
3/8" to 1/2"
the 2 notches on the bottom of log (A) over
(9 -13 mm)
the 2 corresponding locating brackets as
shown.
3. Place the center log (C) as shown. The 2
notches on the bottom of log (C) fi t over
Ground
the corresponding locating brackets.
Electrode
4. Place the left log (B) as shown. The top fork
on log (B) fi ts into the notch on log (A). The
Flame Rod
bottom of log (B) rests on the subfl oor.
5. Place the top right log (D) as shown. The top
Hot Surface
fork on log (D) fi ts into notch on log (A) as
Igniter
shown. The bottom fork on log (D) rests on
subfl oor fl ange (identifi ed in photo #1).
SSDV-4035 - Install as Follows
Carefully position the ceramic fi ber logs into the
fi rebox as shown in Figure 54. Logs should be
placed in the order shown and per the following
instructions.
1. Place embers on the front burner tube and
volcanic stone in front of the burner as
shown and per instructions on this Page
(see Placement of Glowing Embers & Install
Decorative Volcanic Stone on this page).
2. Place the rear log (A) as shown. Position
the 2 notches on the bottom of the log over
the 2 corresponding locating brackets as
shown.
3. Place the center log (C) as shown. The 2
notches on the bottom of the log should fi t
over the corresponding locating brackets.
4. Place the top right log (D) as shown. The top
fork on log (D) fi ts into notch on log (A) as
shown. The bottom fork on log (D) rests on
subfl oor fl ange (identifi ed in photo #1).
5. Place the top left log (B) as shown. The top
fork on log (B) fi ts into notch on log (A). The
bottom of the log rests on the subfl oor.
DO NOT attempt to install the
logs until the appliance instal-
lation has been completed, the
gas line connected and tested
for leaks and the initial burner
operation has been checked
out.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
WARNING
WARNING
The size and position of the log
set is critical to achieve a safe,
reliable and attractive fl ame pat-
tern. Any attempt to use a different
log set in the fi replace will void
the warranty and will result in
incomplete combustion, sooting,
and poor fl ame quality.
WARNING
This appliance is not designed
to burn wood. Any attempt to
do so could cause irrep arable
damage to appliance and prove
hazardous to your safety.
WARNING
If logs are not installed according
to the log installation instruc-
tions, fl ame impingement and
improper combustion could
occur and result in soot and/or
excessive production of carbon
monoxide (CO), a colorless,
odorless, toxic gas.
Glowing Embers
Separate into Quarter
Size (separate) Pieces
Bag of Glowing
Embers (rockwool)
Figure 52
REFERENCE
Firebox Accessories / Parts
Cat. No. Model No. Description
Bag of Glowing Embers
88L53 FGE
(1 oz. rockwool)
Bag of Decorative
80L42 FDVS
Volcanic Stone
Table 13