Tiger M105X/S Mounting And Operating Instructions

Side rotary assemblies

Advertisement

SIDE ROTARY
ASSEMBLIES
KUBOTA M105X/S
CAB / WOC
Current as of 07/12/2010
PARTS LISTING WITH
MOUNTING AND OPERATING
INSTRUCTIONS
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tiger-mowers.com
06070001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M105X/S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tiger M105X/S

  • Page 1 SIDE ROTARY ASSEMBLIES KUBOTA M105X/S CAB / WOC Current as of 07/12/2010 PARTS LISTING WITH MOUNTING AND OPERATING INSTRUCTIONS Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.tiger-mowers.com 06070001...
  • Page 2 TO THE OWNER / OPERATOR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
  • Page 3 This manual contains information about many features of the Tiger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also troubleshooting of your new We recommend that you read carefully the entire manual before operating unit.
  • Page 4: Table Of Contents

    TABLE OF CONTENTS SAFETY_____________________________________________ Safety Information__________________________________ 1-2 ASSEMBLY / MOUNTING SECTION_______________________ OPERATION SECTION_________________________________ MAINTENANCE SECTION______________________________ PARTS SECTION_____________________________________ Parts Ordering Guide_______________________________ Parts Table of Contents______________________________ 5-3 Common Parts Section____________________________ WARRANTY INFORMATION_____________________________ This symbol means: CAUTION – YOUR SAFETY IS AT RISK! When you see this symbol, read and follow the associated instructions carefully or personal injury or damage may result.
  • Page 5: Safety

    SAFETY SECTION...
  • Page 6: General Safety Instructions And Practices

    General Safety Instructions and Practices A safe and careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner / operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death.
  • Page 7 Si no lee Ingles, pida ayuda a alguien que PELIGRO! si lo lea para que le traduzca las medidas de seguridad. (SG-3) Never operate the Tractor or Implement until you have read and DANGER! completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement.
  • Page 8 Never allow children or other persons to ride on the Tractor or Implement. DANGER! Falling off can result in serious injury or death. DANGER! Never allow children to operate or ride on the Tractor or Implement. WARNING! Do not mount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completely stopped.
  • Page 9 WARNING! The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items thrown by the equipment. CAUTION! PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PER- MANENT HEARING LOSS! Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss.
  • Page 10 WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is off before working on the Implement. WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized service parts.
  • Page 11 CAUTION! On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. DANGER! NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement.
  • Page 12 DANGER! The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities.
  • Page 13 Rotary Mowers are capable under adverse conditions of throwing DANGER! objects for great distances serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS: -Front and Rear Deflectors are installed and in good, working condition;...
  • Page 14 WARNING! Never leave the Tractor and Implement unattended while the Implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower the stand and put the retaining pin securely in place, or put a secure support under the A-Frame.
  • Page 15 The rotating parts of this machine continue to rotate even after the Tractor WARNING! has been turned off. The operator should remain in his seat for 60 seconds after the brake has been set, the PTO disengaged, the tractor turned off, and all evidence of rotation has ceased. “Wait a minute...Save a life!”...
  • Page 16 SAFETY Side Rtry Safety Section 1-12...
  • Page 17 ITEM PART NO. QTY. 22839 INSTRUCT 22840 WARNING 24028 WARNING 31522 LOGO 31523 LOGO 42350 DANGER 33743 INSTRUCT 42399 REFLECT 42400 REFLECT 6T3217 DANGER 6T3219 WARNING 6T3220 INTRUCT 6T3221 CAUTION 6T3222 INSTRUCT 1059 INSTRUCT 6T3224 DANGER 6T3230 WARNING 6T3233 CAUTION 6T3234 CAUTION 6T3236...
  • Page 18 SAFETY PART NO. LOCATION 22839 MOWER DECK 22840 INSIDE OF CAB 24028 MOWER DECK 10"X5.5" 31522 MOWER DECK 18.25"X10" 31523 HYDRAULIC TANK Side Rtry Safety Section 1-14...
  • Page 19 SAFETY PART NO. LOCATION 42350 MOWER DECK 33743 INSIDE OF CAB 42399 MOWER DECK 42400 MOWER DECK Side Rtry Safety Section 1-15...
  • Page 20 SAFETY 29-6T3221 Side Rtry Safety Section 1-16 PART NO. LOCATION 6T3217 MOWER DECK 6T3219 INSIDE OF CAB 6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB...
  • Page 21 SAFETY Side Rtry Safety Section 1-17 PART NO. LOCATION 6T3233 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3236 MOWER DECK 6T3243 INSIDE OF CAB...
  • Page 22 SAFETY Side Rtry Safety Section 1-18 PART NO. LOCATION 6T3233 HYDRAULIC TANK 6T3234 INSIDE OF CAB 6T3236 MOWER DECK HYDRAULIC TANK 6T3243 INSIDE OF CAB...
  • Page 23 SAFETY PART NO. LOCATION 6T3249A MOWER DECK 6T3261 MOWER DECK TB1011 MOWER DECK 02962764 MOWER DECK DRAFT BEAM Side Rtry Safety Section 1-19...
  • Page 24 SAFETY Side Rtry Safety Section 1-20 PART NO. LOCATION 02965262 DRAFT BEAM 02967827 CAB FENDER...
  • Page 25 SAFETY 34852 HYDRAULIC TANK 00756059 MOWER DECK Side Rtry Safety Section 1-21...
  • Page 26 ITEM PART NO. QTY. 50023 AVAIL 00776031 33997 AVAIL 33753 34296 34297 6T1823 NOTE: The manual canister can be bolted, zip tied or adhered to a variety of surfaces. Locate a protected area within the view of the operator. Then select an installation method and attach the canister. CAUTION-AVOID DRILL- ING HOLES INTO UNKNOWN AREAS, wires and other parts may be located behind these areas.
  • Page 27: Federal Laws And Regulations

    FEDERAL LAWS AND REGULATIONS This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.
  • Page 28 SAFETY Side Rtry Safety Section 1-24...
  • Page 29: Assembly Section

    ASSEMBLY SECTION Assembly Section 2-1...
  • Page 30: Tractor Preparation

    Before attempting to mount your Tiger mower, it is important to read an understand all of the Safety Messages in the Safety section of this manual. Check complete shipment list against the packing list to make sure there are no shortages.
  • Page 31: Main Frame Installation

    MAIN FRAME INSTALLATION With an overhead hoist and / or jack-stands, raise one side of the frame up to the correctly matching mounting holes. Install capscrews and all other hardware as shown in main frame parts section to secure the sides of the main frame to the tractor casting, DO NOT tighten at this time.
  • Page 32 FRONT PUMP MOUNTING Install the pump mounting bracket on the front of the tractor with capscrews and lockwashers as shown in the parts section illustration. DO NOT tighten fasteners at this time. Slide the pump drive shaft into the crankshaft adapter. The end with the shorter splines should be inserted into the adapter (if applicable).
  • Page 33 ASSEMBLY FILLING HYDRAULIC RESERVOIR Refer to the maintenance section for filling specifications and hydraulic oil requirements. NOTE: Starting or running your Tiger mower before filling reservoir will cause serious damage to hydraulic pump. Assembly Section 2-5...
  • Page 34 VALVE MOUNTING BRACKET The valve mounts are made to fasten to the back fenders of the tractor. The top rear hole on the mounting bracket match an existing hole on the fender. Ream out the existing mounting holes to fit the 3/8” hardware. Attach the valve mounting plate to the brackets.
  • Page 35 2 1/8” HOLE CABLE SWITCH BOX WIRING Refer to the parts section for wiring diagram to hook up the switch box. Cover the four wires from the switch box with plastic wire wrap provided. Route the wires, that tap into the tractors power, from the switch box to the front council panel. Remove the console panel under the steering wheel to access wires.
  • Page 36 HUSCO VALVE MOUNTING Match the holes on the valve to the holes on the valve plate. The holes on the plate for the cables should be on your right. Always start by matching the mounting holes on the Husco valve to the two mounting holes closest to you on the plate. There will be two more holes on the plate to match the other mounting holes on the valve.
  • Page 37 POLYCARBONATE SAFETY WINDOWS NOTE: Installing a boom mower requires that all of the right side windows be replaced with polycarbonate. Install the safety windows after all of the cab wiring and mounting is done; and before the boom arm is mounted. Locate all the hardware in the Parts Section on the Safety Screen page, when installing the polycarbonate.
  • Page 38 INSTALLING O-RING FITTINGS Installing straight, 45° and 90° O-rings requires that the O-ring and washer (A) be up against the swivel body (B). Insert the swivel and turn in until the swivel is pointed in the right direction and the O-ring contact is made. Hold swivel in set direction with a wrench and turn the O-ring contact is made.
  • Page 39 ASSEMBLY WEATHER-PACK/METRI-PACK ASSEMBLY These instructions apply to both Weather-Pack and Metri-pack connectors. NOTE: Use the specific tool for the type of connector you are assembling. 1. Apply seal to cable, before stripping 2. Align seal with cable insulation. 4. Crimp and visually inspect for a good 3.
  • Page 40 COMBO LIFT DRAFT BEAM INSTALLATION Install ½” O-ring breather into butt port of inboard cylinder. Install fittings in the rod end of the cylinder according to the diagram in the commons section. These fittings should be positioned to face the butt end of the cylinder. Next turn the clevis onto the rod of the cylinder until it is tight against the shoulder and lock into place with locking bolt on clevis.
  • Page 41: Stop Bolt Adjustment

    TRAVEL LOCK MOUNTING Install the travel lock bracket with pin and clip on the draft beam. Slide the draft beam and align the travel lock bracket hole with the mounting hole on the main frame. Install the capscrew, lockwasher and hex nut as shown in the picture. Raise the deck/flail to it’s upright position (Deck ear touches to stop bolt as shown in the picture).
  • Page 42 DECK MOUNTING Check that all grease zerks have been installed in the draft beams pivot arm, left linkage arm, right linkage arm, and cylinder mounting ears. Using a clevis pin and roll pins, connect the pivot arm to clevis on draft beam. NOTE: Make sure the longer distance between the cutout and the end of the pivot arm is closest to the draft beam pivot ears on the center tube as shown in the diagram below.
  • Page 43 DECK / MOTOR FEEDLINE Install the 1” hose with the 90 degree flange on the front side of the motor to the inside upper oil port of the solenoid valve. Secure to motor with flange kit, and install swivel fittings on the other end. Install the other 1” hose with the 60 degree flange on the back side of the motor to the inside lower oil port of the solenoid valve.
  • Page 44 FINAL PREPARATION FOR OPERATION Place operators safety and operation decals on the steering column and side counsel where they are clearly visible to the operator. These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book.
  • Page 45: Operation Section

    OPERATION SECTION Operation Section 3-1...
  • Page 46 Safety is of primary importance to the owner / operator and to the manufacturer. The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the messages will be repeated throughout the manual.
  • Page 47 STARTING TRACTOR AND MOWER Check the operators manual received from the tractor manufacturer, for their recommendation and procedures pertaining to your particular make and model. When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow bystanders within 300 feet of the machine when mower is in operation.
  • Page 48: Mower Operation

    The rear mower height is controlled with the 3-point hitch control lever. Follow the instructions for this control is the tractor operators manual. The tilt of the rear mower is controlled with the third spool if the lift valve and is coordinated as shown above. The side and rear mower positions may optionally be controlled with the tractors remote hydraulic connections or a combination of lift valve and remote hydraulics.
  • Page 49 When cutting tall shrubs or small trees (maximum recommended size of material to be cut is 2” diameter) begin each pass at the top of the material and work down with each consecutive pass. Use a low speed to allow the cutting blades time to mulch as well as cut the foliage.
  • Page 50: Transporting Mower

    TRANSPORTING MOWER Transporting under the units own power: When transporting between job sites or between cutting passes, the following procedure should be followed: Shut off the power to the cutting head(s) and allow all motion to come to a complete stop. Raise the draft beam to it’s highest position. Raise the side mower until the deck stops against the draft beam.
  • Page 51 Next, switch the hose ends and reconnect to form two separate closed loops, see diagram below. Disconnect the lift cable from the head and secure the loose end back onto the cable with the cable clevis. Remove the keeper bolt and draft beam outer pivot pin.
  • Page 52 OPERATION INSPECTION SHEETS Side Rtry Operation Section 3-8...
  • Page 53 OPERATION Rotary Mower PRE-OPERATION Inspection Tractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sure the Tractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mower head is resting on the ground (or is securely blocked up and supported) and all hydraulic pressure has been relieved.
  • Page 54 OPERATION TRACTOR PRE-OPERATION Inspection Tractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sure the Tractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mower head is resting on the ground (or is securely blocked up and supported) and all hydraulic pressure has been relieved.
  • Page 55 OPERATION FRONT END LOADER PRE-OPERATION Inspection Mower ID#_____________ Make___________________ Date:__________________ Shift____________________ Before conducting the inspection, make sure the Tractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Loader is resting on the ground (or is securely blocked up and supported) and all hydraulic pressure has been relieved.
  • Page 56 OPERATION TRACTOR PRE-OPERATION Inspection Tractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sure the Tractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Loader is resting on the ground (or is securely blocked up and supported) and all hydraulic pressure has been relieved.
  • Page 57: Maintenance Section

    MAINTENANCE SECTION Maintenance Section 4-1...
  • Page 58: Maintenance Precautions

    MAINTENANCE Tiger Mowers are designed for high performance and rugged durability, yet with simplified maintenance. The purpose of this section of the manual is to help the operator in the regular servicing of the mower. Regular maintenance at the intervals mentioned will result in the maximum efficiency and long life of the Tiger Mower.
  • Page 59: Regular Maintenance

    REGULAR MAINTENANCE The intervals at which regular servicing should be done are based on hours of operation. Use the tractors hour meter to determine when regular servicing is required. This symbol indicates a point that needs to be greased at an interval noted in the section below.
  • Page 60: Trouble Shooting

    MAINTENANCE WEEKLY OR EVERY 50 HOURS ITEM SERVICE In Tank Hyd. Fluid Change Filter (10 micron filter) In-Line High Pressure Change Filter (10 micron filter) MONTHLY OR EVERY 150 HOURS Hydraulic Fluid Level Check Hyd. Tank Breather Clean / Check / Replace Rear Tire Type 480/80R38 18.4-34...
  • Page 61 MAINTENANCE SYMPTOMS CAUSE Oil Temperature rises 1. Low oil level above 200 deg. F 2. Kinked/blocked hoses 2. Inspect / Repair / Replace 3. Worn pump / motor Mower will not start 1. Blown fuse or run 2. Ball valves closed 2. Make sure valves are open 3.
  • Page 62 MAINTENANCE Motor will not work 1. Excessive wear on internal parts NOTE: If flow meter is available, check pressure and flow volume for all suspected hydraulic problems. If the solution to your problem cannot be found in this section, call the Technical Service representative at the number shown on the front cover of this manual.
  • Page 63: Torque Specifications

    MAINTENANCE TORQUE SPECIFICATIONS * These are intended to be general specifications. See tractor operators or service manual for exact specifications for your unit. Maintenance Section 4-7...
  • Page 64: Lubrication Recommendations

    LUBRICATION RECOMMENDATIONS Description Tractor Hydraulics Mower Hydraulics Cold Temperatures 0 F Start-Up Normal Temperatures 10 F Start-Up Normal Temperatures 15 F Start-Up High Operating Temp. Above 90 F Flail Rear Gearbox Cutter Shaft & Ground Roller Shaft (Flail) Drive Shaft Coupler (Flail and Rotary) Drive Shaft Yoke, U-Joint &...
  • Page 65 MAINTENANCE POLYCARBONATE CARE & MAINTENANCE The proprietary UV and Abrasion Resistant surface coating on SHIELDS SUPERCOATED ™ polycarbonate significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are recommended to prolong service life. Tiger Corp. polycarbonate is SUPERCOATED SUPERCOAT™...
  • Page 66: Detailed Maintenance

    RECOMMENDED FILLING INSTRUCTIONS FOR HYDRAULIC RESERVIORS When filling or checking the oil level, the unit should be parked on a level surface, shut “OFF”, and allowed sufficient time to cool to ambient temperature. Use caution when removing the pressurized breather. Do not place face over opening when removing the breather.
  • Page 67 MAINTENANCE DETAILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FILTER ELEMENT: Assure system has been shut down and de-pressurized. Locate High Pressure Filter housing. Confirm that the element that is about to be installed matches the element p/n on the filter model tag. Example: V3.0510-06 (world line 100, HD049 model) Locate the bottom of the High Pressure Bowl, and use the appropriate spanner wrench –or- ratchet that matches the hex pattern.
  • Page 68 MAINTENANCE GREASING INNER AND OUTER DRAFT BEAM PIVOT POINTS Locate the grease zerks on the inner and outer draft beam pivot bosses. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications into each zerk until grease protrudes from joints. Grease all pivots daily or every 8 hours of service.
  • Page 69 MAINTENANCE TIGHTENING KNIFE BOLTS AND DISK BOLTS: After every 8 hours of operation or daily, the Knife Bolts and Disk Bolts should be tightened as follows: Knife mounting bolts (2ea.) torque oiled to 800 ft. lbs. Disk mounting bolts (6ea. ) torque dry to 204 or oiled to 184 ft. lbs. With the cutter head lowered, locate the grease zerks on the linkage and pivot bosses.
  • Page 70 MAINTENANCE GREASING PUMP DRIVE SHAFT COUPLER: With engine stopped, ensure drive shaft alignment by grasping coupler and sliding back and forth. Coupler should slide freely with approximately 1/8” of end play. If coupler does not slide freely, inspect for loose pump mount bolts, or damaged or loose crank shaft adapter.
  • Page 71 MAINTENANCE ADJUSTING THE CABLE LIFT Extend the outboard cylinder until the mower deck touches its stop on the draft beam as shown. NOTE: Make sure the cable turnbuckle is loose enough to allow the cylinder to reach full extension before the head reaches the stop. Now hold the head against the stop and tighten the turnbuckle until the cable is tight.
  • Page 72 MAINTENANCE GREASING SPINDLE Locate grease fitting on inside of deck housing. Inject Tiger Spindle Lubricant, part number 06540000 into spindle housing. Fill with lubricant until lubricant weeps out of the top spindle seal. Lubricate spindle weekly or every 40 hours of use. TIGHTENING SPINDLE BOLTS The spindle mounting bolts should be checked and retorqued daily or every 10 hours of service.
  • Page 73 MAINTENANCE GREASING MOTOR SPLINE TO SPINDLE SPLINE Locate motor spline and spindle spline on the mower deck. Grease splines with Mobil moly 52. Use about 4 ounces of grease. Change grease yearly or every 500 hours. Maintenance Section 4-17...
  • Page 74: Rotary Knife Replacement

    MAINTENANCE INSPECTION OF ROTARY KNIVES Failure to follow the following warnings and instructions may result serious injury or damage to the equipment or property! 1 – DO NOT weld on the knife or bolts. Damaged or worn knives must be replaced. 2 –...
  • Page 75 MAINTENANCE REPLACEMENT OF ROTARY DISK Failure to follow the following warnings and instructions may result serious injury or damage to the equipment or property! The bolts that attach the knife mounting disk to the spindle must be grade 8. These 5/8 inch bolts are to be torqued to 204 dry or 184 oiled ft. lbs. A thread locking agent may be applied to threads of all mounting bolts before they are installed.
  • Page 76 MAINTENANCE HEAVY DUTY SPINDLE ASSEMBLY INSTALLATION AND BEARING ADJUSTMENT WARNING! A press MUST be used to install bearing cups, bearing cones, and seals. DO NOT use a hammer to install races, bearings, or seals. The parts of assembly may be damaged. NOTE: The grease zerk and gussets are located on the top side of the spindle housing.
  • Page 77: Bearing Installation

    MAINTENANCE BEARING INSTALLATION 1 – Press upper bearing cup into the spindle housing. 2 – Turn the spindle housing over and press in the lower bearing cup. 3 – Place the lower bearing cone in the bearing cup. Next press the seal into the spindle housing.
  • Page 78: Bearing Adjustment

    MAINTENANCE BEARING ADJUSTMENT 1 – Clamp the bottom end of the spindle securely in a vise so the spindle housing turns freely. 2 – Position a magnetic base dial indicator on the outer diameter of the spindle housing. Locate the end of the dial indicator against the flat end of the spindle shaft. The dial indicator will now measure accurately bearing end play.
  • Page 79: Daily Maintenance Schedule

    DAILY MAINTENANCE SCHEDULE The following services should be performed daily or every 8 hours of service, following the detailed maintenance instructions in the operators manual. ______ Pump Drive Shaft: Check for end play in drive shaft / coupler and ______ Crankshaft adapter: If equipped with rubber grommets check ______ Pivot points: Inject grease until it appears at ends.
  • Page 80 MAINTENANCE Maintenance Section 4-24...
  • Page 81: Parts Section

    SIDE ROTARY KUBOTA M105X PARTS SECTION Parts Section 5-1...
  • Page 82: Parts Ordering Guide

    PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.
  • Page 83: Parts Section Table Of Contents

    PARTS SECTION TABLE OF CONTENTS SECTION TRACTOR SPECIFIC PARTS: TRACTOR MNT. KIT - MAIN FRAME M105X TRACTOR MOUNT KIT - HYDRAULICS M105X COMBO DRAFT BEAM 2SP HUSCO CONTROLS - KUBOTA M105X 2SP HUSCO LIFT VALVE - COMBO 2SP HUSCO LIFT VALVE - CABLE HUSCO VALVE BREAKDOWN HUSCO VALVE BREAKDOWN SAFETY SCREEN - KUBOTA M105X...
  • Page 84: Tractor Mnt. Kit - Main Frame M105X 06101300

    TRACTOR MOUNT KIT - MAIN FRAME M105X 5-22-06 Parts Section 5-4...
  • Page 85 TRACTOR MOUNT KIT - MAIN FRAME M105X ITEM PART NO. 06300043 06300044 06300045 23152 06380026 06510083 34666 33695 35269 21627 06505077 TF4887 6T0649 06505067 06410394 35131 06530531 06530530 6T2521 21833 21732 21644 21730 33764 06533003 33880 22016 21990 21988 21989 21825 21725 21625...
  • Page 86: Tractor Mount Kit - Hydraulics M105X

    TRACTOR MOUNT KIT - HYDRAULICS M105X 5-24-06 Parts Section 5-6...
  • Page 87 TRACTOR MOUNT KIT - HYDRAULICS M105X ITEM PART NO. 33695 35269 06380026 23152 06510083 TF4852 33554 33555 TF4431 34389 34309 06503054 34064 6T0375B 06420045 06700043 6T0450 24937 06537004 6T3202 6T3218 06400393 24962 27724 32519 22014 06500248 06500249 06500214 34161 34154 34638 34162 34155...
  • Page 88: Combo Draft Beam

    COMBO DRAFT BEAM Parts Section 5-8...
  • Page 89 COMBO DRAFT BEAM ITEM PART NO. QTY. 32143 6T0151R 32215 TF4500A TF4507B TF4506B 30126B 6T3001 TF4519 6T3003D TB1023 6T3002A 6T3004 22023 23724 22847 22076 22077 6T3207 6T3211 6T4258 34244 34396 21688 21677 21635 21627 21831 21825 30781 NOTE: ITEM 35 IS USED ON THE GLAND END OF ITEM 2 (AS NEEDED) Parts Section 5-9 DESCRIPTION BEAM,DRAFT,JD5520-25...
  • Page 90: 2Sp Husco Controls - Kubota M105X

    2 SPOOL HUSCO CONTROLS - KUBOTA M105X 4-27-06 Parts Section 5-10...
  • Page 91 2 SPOOL HUSCO CONTROLS - KUBOTA M105X ITEM PART NO. 6T1251 21542 21525 21986 06510102 34496 32359 34508 6T3952 23865B 27082B 21636 21627 34623 QTY. DESCRIPTION CBL CTRL BOX,180 DEG CAPSCREW,1/4 X 4 NC HEX NUT,1/4 NC LOCKWASHER,1/4 SWITCHBOX,SIDE,GND BRKT,SWITCHBOX,UNI SCREW,MACHINE,8-32X3/4 WASHER,FENDER,#10 HEX NUT,8/32 NYLOCK...
  • Page 92: 2Sp Husco Lift Valve - Combo

    2SP HUSCO LIFT VALVE - COMBO 4-27-06 Parts Section 5-12...
  • Page 93 2SP HUSCO LIFT VALVE - COMBO ITEM PART NO. QTY. 06340023 06340024 21631 21627 22016 06430044 21625 34622 06505029 21579 30801 21632 34623 6T4411 21500 6T3017 33271 34631 34632 33591 32678 33382 33383 33649 06503066 33486 06503036 Parts Section 5-13 DESCRIPTION VALVE MNT,RH,KUB,M105X VALVE MNT,LH,KUB,M105X...
  • Page 94: 2Sp Husco Lift Valve - Cable

    2SP HUSCO LIFT VALVE - CABLE Parts Section 5-14...
  • Page 95 2SP HUSCO LIFT VALVE - CABLE ITEM PART NO. QTY. 06340023 06340024 21631 21627 22016 06430044 21625 34622 06505029 21579 31752 21632 34623 6T4411 21500 6T3017 33271 34631 34632 33591 32678 33382 33383 33649 06503066 33486 06503036 Parts Section 5-15 DESCRIPTION VALVE MNT,RH,KUB,M105X VALVE MNT,LH,KUB,M105X...
  • Page 96 2SP HUSCO VALVE - POWER BEYOND (30801) Parts Section 5-16...
  • Page 97 2SP HUSCO VALVE - POWER BEYOND (30801) ITEM PART NO. QTY TB1017S TB1702 TB1017P 06502091 TB1017M TB1017E TB1017M TB1017M TB1017A TB1017L TB1017X 24214 DESCRIPTION INLET END COVER END COVER, POWER BEYOND VALVE SECTION (SINGLE ACTING, SPRING DETENT) VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (NO AUX VALVE PORTS) SHUT-OFF PLUG RELIEF VALVE, 2250 PSI...
  • Page 98 2SP HUSCO VALVE - POWER BEYOND (31752) Parts Section 5-18...
  • Page 99 2SP HUSCO VALVE - POWER BEYOND (31752) ITEM PART NO. QTY TB1017S TB1702 TB1017P TB1017P TB1017M TB1017E TB1017M TB1017M TB1017A TB1017L TB1017X 24214 DESCRIPTION INLET END COVER END COVER, POWER BEYOND VALVE SECTION (SINGLE ACTING, SPRING DETENT) VALVE SECTION (SINGLE ACTING, SPRING DETENT) SHUT-OFF PLUG RELIEF VALVE, 2250 PSI SHUT-OFF PLUG...
  • Page 100 SAFETY SCREEN - KUBOTA M105X Parts Section 5-20...
  • Page 101 SAFETY SCREEN - KUBOTA M105X ITEM PART NO. QTY. 06490023 31965 20’ 06520040 06410391 06410392 06537000 06537001 21538 27506 21580 06530511 21532 22014 22015 21527 21577 22645 Parts Section 5-21 DESCRIPTION POLYCARB,FRMD,KUB,M105X,RH TRIM SEAL,3/8 CLIP X 3/4 OD BRKT,JD,POLY,RETAIN MNT,POLY,KUB MNT,SM,POLY,KUB WASHER,NEOPRENE,.25x1x.38 WASHER,RUBBERIZED,.25,CONICAL...
  • Page 102 OPTIONAL PUMP GUARD KIT ITEM PART NO. QTY. 32430 21831 21993 21825 Parts Section 5-22 DESCRIPTION UNIVERSAL PUMP GUARD CAPSCREW - 3/4 X 1 3/4 LOCKWASHER - 3/4 HEX NUT - 3/4 11-20-01...
  • Page 103 OPTIONAL PUMP AND GRILL GUARD KIT ITEM PART NO. QTY. 32430 32737 21833 22021 21993 21825 Parts Section 5-23 DESCRIPTION UNIVERSAL PUMP GUARD UNIVERSAL GRILL GUARD CAPSCREW - 3/4 X 2 1/4 FLATWASHER - 3/4 LOCKWASHER - 3/4 HEX NUT - 3/4 11-20-01...
  • Page 104 FUEL TANK - KUBOTA M105X ITEM PART NO. QTY. 06370048 06370049 06503061 06503063 06503092 22016 21627 6T3200 06503091 Parts Section 5-24 DESCRIPTION FUEL TANK,RH,KUB,M105X TANK STRAP,KUB,M105X ADAPTER,1 1/4NPTx1 1/4BARB ELBOW,3/8NPTx3/8BARB ELBOW,1/4NPTx1/4BARB FLATWASHER,3/8 NYLOCK NUT,3/8 NC SPLIT HOSE EXISTING HARDWARE EXISTING HARDWARE EXISTING HARDWARE ADAPTER...
  • Page 105: Switch Box Schematic

    SWITCH BOX SCHEMATIC Parts Section 5-25...
  • Page 106 SOLENOID BRAKE VAVLE ASSEMBLY ITEM PART NO. QTY. 34092 34095 34094 06510095 34093 Parts Section 5-26 DESCRIPTION BRAKE VALVE, BLANK RELIEF VALVE, 3000 PSI LOGIC ELEMENT METRI PAK COIL CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER)
  • Page 107 SOLENOID BRAKE VALVE HYDRAULIC SCHEMATIC BRAKE VALVE TROUBLESHOOTING FAILURE MODE: - MOWER WILL NOT START - system pressure is low (engine not lugging). - MOWER WILL NOT START - system pressure is high (engine lugging). “MR” port will be high pressure. - MOWER WILL NOT ROTATE AT FULL SPEED - limited power.
  • Page 108 Parts Section 5-28...
  • Page 109: Common Parts Section

    SIDE ROTARYCOMMON SECTION COMMON PARTS SECTION Side Rotary Common Section 6 - 1...
  • Page 110 TABLE OF CONTENTS SECTION CABLE LIFT ASSEMBLY COMBO DRAFT BEAM 60” SIDE CABLE ROTARY MOWER ASSEMBLY 72” SIDE CABLE ROTARY MOWER ASSEMBLY 60” SIDE COMBO RTRY MOWER ASSEMBLY 60” SIDE ROTARY MOWER 60” SPINDLE AND SPACER 72” SIDE COMBO ROTARY MOWER ASSY TM72”...
  • Page 111 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.
  • Page 112 CABLE LIFT ASSEMBLY 3-22-02 Side Rotary Common Section 6 - 4...
  • Page 113 CABLE LIFT ASSEMBLY ITEM PART NO. QTY. 6T0103A 6T0103E OPT. 6T0103L OPT. 6T0105 OPT. 6T0108 OPT. 6T0150 6T0151R 6T0100 6T0101 33768 6T0110 6T0110E OPT. 6T0110L OPT. 6T0115 6T0112 6T2999 6T3001 6T3005 TB1033 6T3004 6T3010 6T3009 6T3020 6T2272 6T3211 21836 21688 21825 21677 22023...
  • Page 114: Combo Draft Beam

    COMBO DRAFT BEAM 3-22-02 Side Rotary Common Section 6 - 6...
  • Page 115 COMBO DRAFT BEAM ITEM PART NO. QTY. 06350001 31063 OPT. 6T0151R 32215 25343 TF4500A TF4507B TF4506B 30126B TF4514A 6T3001 TF4519 TB1033 06537021 6T3005 6T3004 6T2614 TB3010 22847 22076 22077 6T3207 6T3211 6T4258 34244 34396 21688 21675 21635 21625 21831 21825 06700095 NOTES: 1.
  • Page 116 60” SIDE CABLE ROTARY MOWER Side Rotary Common Section 6 - 8...
  • Page 117 60” SIDE CABLE ROTARY MOWER ITEM PART NO. QTY. 32099 21225B 22592 6T0823 6T0822 6T0822A 6T1001 06504011 23172 6T1024H5 21223 6T1033 SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE...
  • Page 118 72” SIDE CABLE ROTARY MOWER Side Rotary Common Section 6 - 10...
  • Page 119 72” SIDE CABLE ROTARY MOWER ITEM PART NO. QTY. 21225B 21295B 21242A 6T0822 6T0822A 6T1001 06504018 21222 6T1024H5 21223 6T1033 SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE 21248...
  • Page 120 60” SIDE COMBO ROTARY MOWER Side Rotary Common Section 6 - 12...
  • Page 121 60” SIDE COMBO ROTARY MOWER ITEM PART NO. QTY. 32617 30188D 31773 6T1001 6T0820H 22592 6T0823 6T1024H5 6T2290 21223 6T2277 21993 6T2413 6T2270 22016 21625 21631 21783 21992 21775 25270 6T0822 6T0822A 06504011 23172 6T1029 6T1033 21733 21990 21725 SEE OLD ROTARY KNIVES AND DISKS PAGE SEE OLD ROTARY KNIVES AND DISKS PAGE SEE OLD ROTARY KNIVES AND DISKS PAGE SEE OLD ROTARY KNIVES AND DISKS PAGE...
  • Page 122 60” SIDE ROTARY MOWER 8/26/05 Side Rotary Common Section 6 - 14...
  • Page 123 60” SIDE ROTARY MOWER ITEM PART NO. QTY . 34975 06320005 06320008 34980 06504016 34981 06410254 22992 *156 6T2270 22016 21625 6T1025 06533006 21990 34972 21631 34974 34973 16 - 20 SEE NEW ROTARY KNIVES AND DISKS PAGE 21988 6T2290 21575 21580 21987...
  • Page 124 60” SIDE ROTARY SPINDLE AND SPACER Side Rotary Common Section 6 - 16...
  • Page 125 60” SIDE ROTARY SPINDLE AND SPACER ITEM PART NO. QTY. 34975 06320005 06320008 34980 06320011 06533004 06530221 25270 6T2290 SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE Side Rotary Common Section 6 - 17...
  • Page 126 72” SIDE COMBO ROTARY MOWER Side Rotary Common Section 6 - 18...
  • Page 127 72” SIDE COMBO ROTARY MOWER ITEM PART NO. QTY. 34260 31408A 31931 6T1001 21248 21295B 21242A 6T1024H5 6T2290 21223 6T2277 21993 6T2413 6T2270 22016 21625 21631 21783 21992 21775 25270 6T0822 6T0822A 06504018 21222 6T1029 6T1033 21733 21990 21725 SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE SEE NEW ROTARY KNIVES AND DISKS PAGE...
  • Page 128: Tm72" Motor Assembly

    TM72” MOTOR ASSEMBLY ITEM PART NO. QTY. 06504018 TF4852 34943 24724 06500444 06500445 Side Rotary Common Section 6 - 20 DESCRIPTION MOTOR KIT,FLANGE,#20 ELBOW,#20FLG x #16MJ ELBOW,#16FJX x #16MJ45 HOSE,#16 x 141 HOSE,#16 x 145...
  • Page 129 PAGE INTENSIONALLY LEFT BLANK Side Rotary Common Section 6 - 21...
  • Page 130: Chain Guards

    CHAIN GUARDS Side Rotary Common Section 6 - 22...
  • Page 131 SIDE ROTARY CHAIN GUARDS 60” SIDE ROTARY ITEM PART NO. QTY. 31773 STD. 31762 28407 12’ 22993 28408 ** NOT SHOWN 72” SIDE ROTARY ITEM PART NO. QTY. 31931 STD. 31863 28407 14’ 22993 28408 ** NOT SHOWN Side Rotary Common Section 6 - 23 DESCRIPTION GAURD,CHAIN,SR60,FRONT ASSY GUARD,CHAIN,TM60,FRONT...
  • Page 132 SIDE ROTARY CASTER WHEEL ASSEMBLY Side Rotary Common Section 6 - 24...
  • Page 133 SIDE ROTARY CASTER WHEEL ASSEMBLY ITEM PART NO. QTY. 25214C 22057C 6T2617 28548 22065 22066 22070 22071 22073 22533 6T0830 6T0838 23329 21416 22697 22696 6T3014 21925 22023 22753 22058 22059B 21775 21992 21782 22060 TF1143 TB3010 31460 6T3207 6T3211 21441 21442 NOTE: CASTER WHEEL ASSEMBLY IS BROKEN DOWN LATER IN THE MANUAL...
  • Page 134: Reservoir Tank Filter Assembly

    RESERVOIR TANK FILTER ASSEMBLY Side Rotary Common Section 6 - 26...
  • Page 135 RESERVOIR TANK FILTER ASSEMBLY ITEM PART NO. QTY. 06505044 AVAIL 28583 06505045 06505046 06505047 06505048 35259 06505049 Side Rotary Common Section 6 - 27 DESCRIPTION FILTER ASSY SAE 10 MICRON CAPSCREW,8MMX25MM(1.25 PITCH) COVER SEAL KIT SPRING BYPASS FILTER,10 MIC,RETURN LINE CAN/BODY...
  • Page 136 MOWER SPINDLE ASSEMBLY - 6T1024H5 Side Rotary Common Section 6 - 28...
  • Page 137 MOWER SPINDLE ASSEMBLY - 6T1024H5 ITEM PART NO. QTY. 6T1024H5 AVAIL 6T1031 6T1016 22596 6T1015 6T1014 6T1011 6T1012 6T1013 6T1010H 30570 33990 6T1013H 6T1012H 6T1011H 6T1019 PT1018H-5 06503064 32572 AVAIL Side Rotary Common Section 6 - 29 DESCRIPTION SPINDLE ASSEMBLY COMPLETE SPROCKET BEARING LOCK NUT - THICK JAM WASHER...
  • Page 138 MOWER SPINDLE ASSEMBLY - 34980 Side Rotary Common Section 6 - 30...
  • Page 139 MOWER SPINDLE ASSEMBLY - 34980 ITEM PART NO. QTY. 34978 34979 6T1013 6T1012 6T1011 6T1014 6T1013H 6T1012H 6T1011H 34985 6T2275 34988 6T3207 06503064 Side Rotary Common Section 6 - 31 DESCRIPTION SPINDLE MOUNT SPINDLE,TM60",NEW BEARING CUP BEARING,CONE SEAL,UPPER (SET OF 2) SLEEVE,ADJ BEARING BEARING CUP,HD BEARING,CONE,HD...
  • Page 140: Hydraulic Lift Cylinder

    HYDRAULIC LIFT CYLINDER Side Rotary Common Section 6 - 32...
  • Page 141 HYDRAULIC LIFT CYLINDER 3” X 10” CYLINDER # 6T0151R ITEM PART NO. QTY. 6T0167 6T0170 6T0178 6T0164 6T0161 6T0173 6T0179 6T0176 6T0187 AVAIL 3” X 12” CYLINDER # 32215 ITEM PART NO. QTY. 6T0167 6T0170 6T0178 6T0204 6T0203 6T0173 6T0179 6T0205 6T0187 AVAIL...
  • Page 142: Rotary Knives And Disks

    ROTARY KNIVES AND DISKS ITEM PART NO. QTY. 34876 6T1023R 34878 34497 34685 34684 34682 25270 6T2290 6T1825 27167 AVAIL 06700002 AVAIL Side Rotary Common Section 6 - 34 DESCRIPTION BLADE MOUNTING DISK NYLOCK HEX NUT 1 1/8” SPACER KNIFE MOUNTING BOLT KNIFE,60"...
  • Page 143: Caster Wheel Assembly

    CASTER WHEEL ASSEMBLY ITEM PART NO. QTY. 21459 21987 21575 28548 22697-1 21416 22696-1 22070 22533 6T0836 22073 22071 22066-1 Side Rotary Common Section 6 - 35 DESCRIPTION SPINDLE, CASTER WHEEL AXLE LOCKWASHER, 5/16” HEX NUT, 5/16” CAPSCREW, 5/16” x 3/4”, NC RIM, OUTER/RR RTRY CASTER ASSY TIRE,SOLID,RR-RTRY RIM,REAR ROTARY CASTER...
  • Page 144 ROTARY MOTOR Side Rotary Common Section 6 - 36...
  • Page 145 ROTARY MOTOR 60” ROTARY MOTOR ITEM PART NO. QTY. 06504011 AVAIL 06504103 22790 06504088 06504062 06504090 06504104 06504078 06504092 06504093 06504094 06504095 02961940 02962200 06504096 6T5101 06504097 22797 06504098 06504099 06504100 06504101 6T5809 06504102 72” ROTARY MOTOR ITEM PART NO. QTY.
  • Page 146 HYDRO PUMP & TSR MOTOR FRONT PUMP TSR MOTOR Side Rotary Common Section 6 - 38...
  • Page 147: Front Hydraulic Pump

    HYDRO PUMP & TSR MOTOR FRONT HYDRAULIC PUMP ITEM PART NO. QTY. 23152 AVAIL 22765 22766 22767 22768 22769 22770 22771 22772 22773 22774 22779 23824 22781 6T5322 AVAIL 24150 AVAIL TSR MOTOR ITEM PART NO. QTY. 06504016 AVAIL 22790 06504088 06504111 06504110...
  • Page 148 SIDE COOLER Side Rotary Common Section 6 - 40...
  • Page 149 SIDE COOLER ITEM PART NO. QTY. 21530 21986 22014 35176 06370015 06380006 06380007 06510026 21629 21988 22016 34117 Side Rotary Common Section 6 - 41 DESCRIPTION CAPSCREW,1/4 X1 NC LOCKWASHER,1/4 FLATWASHER,1/4 1/4 U-NUT SCREEN,COOLER,FRNT MNT,COOLER,BUMPER TANK,RH MNT,COOLER,BUMPER TANK,LH COOLER,FRONT MNT CAPSCREW,3/8 X 3/4 NC LOCKWASHER,3/8 FLATWASHER,3/8...
  • Page 150 2SP HUSCO - POWER BEYOND (30801) Side Rotary Common Section 6 - 42...
  • Page 151 2SP HUSCO - POWER BEYOND (30801) ITEM PART NO. QTY TB1017S TB1702 TB1017P 06502091 TB1017M TB1017E TB1017M TB1017A TB1017L TB1017X 24214 Side Rotary Common Section 6 - 43 DESCRIPTION INLET END COVER END COVER, POWER BEYOND VALVE SECTION (SINGLE ACTING, SPRING DETENT) VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (NO AUX VALVE PORTS) SHUT-OFF PLUG...
  • Page 152 2 SP HUSCO - LOAD SENSE (31320) Side Rotary Common Section 6 - 44...
  • Page 153 2 SP HUSCO - LOAD SENSE (31320) ITEM PART NO. QTY 31595 31594 31597 31597 06503067 06503067 6T4209 31862 31862 31593 TB1017L 31603 TB1017X 24214 Side Rotary Common Section 6 - 45 DESCRIPTION INLET END COVER END COVER, LOAD SENSE VALVE SECTION (DOUBLE ACTING, CENTER SPRING) VALVE SECTION (DOUBLE ACTING, CENTER SPRING) RELIEF PLUG...
  • Page 154 2 SP HUSCO - LOAD SENSE (31321) Side Rotary Common Section 6 - 46...
  • Page 155 2 SP HUSCO - LOAD SENSE (31321) ITEM PART NO. QTY 31595 31594 31597 31597 06503067 31861 6T4209 31862 31862 31593 TB1017L 31603 TB1017X 24214 Side Rotary Common Section 6 - 47 DESCRIPTION INLET END COVER END COVER, LOAD SENSE VALVE SECTION (DOUBLE ACTING, CENTER SPRING) VALVE SECTION (DOUBLE ACTING, CENTER SPRING) RELIEF PLUG...
  • Page 156 2SP HUSCO - POWER BEYOND (31752) Side Rotary Common Section 6 - 48...
  • Page 157 2SP HUSCO - POWER BEYOND (31752) ITEM PART NO. QTY TB1017S TB1702 TB1017P TB1017P TB1017M TB1017E TB1017M TB1017M TB1017A TB1017L TB1017X 24214 Side Rotary Common Section 6 - 49 DESCRIPTION INLET END COVER END COVER, POWER BEYOND VALVE SECTION (SINGLE ACTING, SPRING DETENT) VALVE SECTION (SINGLE ACTING, SPRING DETENT) SHUT-OFF PLUG RELIEF VALVE, 2250 PSI...
  • Page 158 2SP HUSCO - LOAD SENSE (06502040) Side Rotary Common Section 6 - 50...
  • Page 159 2SP HUSCO - LOAD SENSE (06502040) ITEM PART NO. QTY 31595 31594 31597 31597 06503067 06503067 06503068 31862 31862 31593 TB1017L 31603 TB1017X 24214 Side Rotary Common Section 6 - 51 DESCRIPTION INLET END COVER END COVER, LOAD SENSE VALVE SECTION (DOUBLE ACTING, CENTER SPRING) VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (REMOVE SHUTTLE DISC) RELIEF PLUG...
  • Page 160 2SP HUSCO - LOAD SENSE (06502042) Side Rotary Common Section 6 - 52...
  • Page 161 2SP HUSCO - LOAD SENSE (06502042) ITEM PART NO. QTY 31595 31594 31600 31600 06503067 31861 06503068 6T4209 31862 31862 31593 TB1017L 31603 TB1017X 24214 Side Rotary Common Section 6 - 53 DESCRIPTION INLET END COVER END COVER, LOAD SENSE VALVE SECTION (DOUBLE ACTING, DETENT FLOAT) VALVE SECTION (DOUBLE ACTING, DETENT FLOAT) (REMOVE SHUTTLE DISC)
  • Page 162: Solenoid Valve Assembly

    SOLENOID VALVE ASSEMBLY ITEM PART NO. QTY. 06502007 AVAIL 06502008 AVAIL 34689 06505026 06502009 6T3911 6T3908 6T3910 6T4209 TF1228 21987 21586 Side Rotary Common Section 6 - 54 DESCRIPTION VALVE ASY HIGH PRESSURE VALVE ASY LOW PRESSUTE SOLENOID COIL SOLENOID SOLENOID VALVE KIT SOLENOID SEAL KIT RELIEF PILOT 2150 PSI LOW PRESSURE...
  • Page 163: Solenoid Brake Valve Assembly

    SOLENOID BRAKE VALVE ASSEMBLY ITEM PART NO. QTY. 34115 AVAIL 34092 34095 34094 34093 34091 34689 34096 34097 34098 Side Rotary Common Section 6 - 55 DESCRIPTION SOLENOID BRAKE VALVE ASSEMBLY - HIGH PRESSURE BRAKE VALVE, BLANK RELIEF VALVE, 3000 PSI LOGIC ELEMENT CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT &...
  • Page 164 BRAKE VALVE ASSEMBLY W/ METRI PAK ITEM PART NO. QTY. 34092 34094 34095 06510095 34093 34091 Side Rotary Common Section 6 - 56 DESCRIPTION BRAKE VALVE, BLANK LOGIC ELEMENT RELIEF VALVE, 3000 PSI METRI PAK COIL CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) RELIEF VALVE, 2600 PSI...
  • Page 165 SOLENOID BRAKE VALVE HYDRAULIC SCHEMATIC BRAKE VALVE TROUBLESHOOTING FAILURE MODE: - MOWER WILL NOT START - system pressure is low (engine not lugging). - MOWER WILL NOT START - system pressure is high (engine lugging). “MR” port will be high pressure. - MOWER WILL NOT ROTATE AT FULL SPEED - limited power.
  • Page 166: Travel Lock Lift Beam

    TRAVEL LOCK LIFT BEAM ITEM PART NO. QTY. 6T0105 6T0106 6T0107 6T3020 21833 21825 21993 22021 22600 22604 22601C REF. Side Rotary Common Section 6 - 58 DESCRIPTION DRAFT BEAM (STD WITH TRAVEL LOCKS) TRAVEL LOCK BRACKET TRAVEL LOCK PINS 3/4” X 3 1/4” R - CLIP 5/32”...
  • Page 167: Side Mower Travel Lock (Combo)

    SIDE MOWER TRAVEL LOCK (COMBO) ITEM PART NO. QTY. 6T0106 6T0107 6T3020 21833 21825 21993 22021 REF. Side Rotary Common Section 6 - 59 DESCRIPTION COMBO DRAFT BEAM- REFER TO DRAFT BEAM PARTS TRAVEL LOCK BRAKCET TRAVEL LOCK PIN (3/4” x 3-1/4”CAPPED) R-CLIP, 5/32”...
  • Page 168 SWITCHBOX SERVICE PARTS ITEM QTY. 06514013 SWBX,ALUM,BLK,06510102 35226 SWITCH,MOWER,COLEHERSEE 33811 SWITCH,MASTER/DECK FLOAT 6T3923 INDICTATOR LIGHT,ON,RED 06514014 BREAKER,10A,SWBX 34540 STRAIN RELIEF,3/4,BLACK,NYLON 06550018 DECAL,SWTCHBX,TM/TSF,CG 35227 RELAY,DP,DT,12V,LY2F,35226 Side Rotary Common Section 6 - 60 DESCRIPTION...
  • Page 169: Switchbox Schematic

    SWITCHBOX SCHEMATIC Side Rotary Common Section 6 - 61...
  • Page 170 Side Rotary Common Section 6 - 62...
  • Page 171: Warranty

    WARRANTY SECTION Warranty Section 7-1...
  • Page 173: Warranty Information

    WARRANTY INFORMATION Tiger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrants to the original Retail Customer, the new Tiger equipment is free of defects in material and workmanship. Any part of equipment that in Tiger’s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the failure of part(s) shall have occurred within twelve (12) months from the date of delivery of said equipment to the Retail Customer.
  • Page 174 ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter. By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator.
  • Page 175 TO THE OWNER / OPERATOR / DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health Act (OSHA 1928.51 subpart C) makes the following minimum requirements for tractor operators.
  • Page 176 Printed in USA © Tiger Corporation...

This manual is also suitable for:

Kubota m105xKubota m105s

Table of Contents