Table of contents 1 Welcome! ..........................................5 About the product....................................6 What's in the box....................................6 Product overview....................................7 2 Display installation ......................................9 Unlocking the height mechanism.............................10 Adjusting the display position..............................10 Removing the connector compartment cover........................11 Connecting the signal cables ..............................11 Routing the cables & Reattach the connector compartment cover ..............12 VESA-mount installation................................13 First time starting up..................................15 3 Daily operation.........................................17...
• External power supply If you ordered a Barco display controller, it's also in the box together with its accessories. A dedicated user guide is available on the system CD. Keep your original packaging. It is designed for this display and is the ideal protection during transport and storage.
Welcome! 1.3 Product overview Front Image 1-1 USB-A 2.0 downstream connector Left key Right key Menu key Standby key Power status LED Front sensor K5902060 /09 Coronis 3MP LED Display...
Page 8
Welcome! Back Image 1-2 +24 VDC power input +5 VDC, 0.5A power output DisplayPort video input DVI video input Ethernet connector USB-B 2.0 upstream connector USB-A 2.0 downstream connector Connector compartment cover Kensington security lock VESA mount cover plate Cable duct Foot lock clip The Ethernet connection is used for maintenance purposes and is not supported for user application.
Prior to installing your Coronis 3MP LED Display and connecting all necessary cables, make sure to have a suitable display controller physically installed in your computer. If you are using a Barco display controller, please consult the user guide delivered with it to do this.
Display installation 2.1 Unlocking the height mechanism To remove the clip: Position the display with its rear side facing you. Pull the red clip out of the fixation hole in the foot. Image 2-1 Keep the clip in the dedicated hole in case the display needs to be shipped later. 2.2 Adjusting the display position To adjust the display position Stand at the front side of the panel and take the panel at both sides.
Display installation 2.3 Removing the connector compartment cover To remove the connector compartment cover Gently push the two lips on top of the cover Pull the top of the cover slightly away from the display and lift the cover upwards. Image 2-3 2.4 Connecting the signal cables CAUTION: Only connect one of the two video links.
Display installation Image 2-5 If you want to make use of the display's USB upstream connector, connect a PC USB downstream connector to the display's USB upstream connector. Image 2-6 If you have chosen to use the display's USB downstream connector, connect a USB device to the downstream connector.
Display installation Image 2-8 To Reattach the connector compartment cover Reattach the connector compartment cover by sliding the cover's bottom in position and then push the cover's top. You'll hear a “click” sound of the cover's clips when the connector compartment cover is in position. Image 2-9 2.6 VESA-mount installation WARNING: Never move a display attached to an arm by pulling or pushing the display itself.
Page 14
Display installation Image 2-10 Put the display face down on a clean and soft surface. Be careful not to damage the panel screen. Remove the plastic cover with a flathead screw driver. Image 2-11 Slide the plastic cover over the neck of the foot. Image 2-12 Remove the four screws fixing the foot while supporting the foot.
Your Coronis 3MP LED Display will be running in a basic video mode at a default refresh rate when first time starting up. If you are using a Barco display controller, please consult the user guide delivered with it to install the drivers, software and documentation. When this is done, your display will automatically detect the connected video input signal(s) and apply the correct video mode and refresh rate.
Page 16
Display installation K5902060 /09 Coronis 3MP LED Display...
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels.
Daily operation illuminated and are now available for further actions. However, if no further actions are taken within the following 5 seconds, the keys will dim again. The I-Luminate/Left key is always lit and available for activation of the I-Luminate feature. Please refer to “I-Luminate”, page 20 for more information.
When the display is in power on mode and the OSD menu is not shown, I-Luminate can be activated by touching the I-luminate/left key. Unlike other Barco products, especially designed for tomography, in the MDCG-3221, I-Luminate supports one mode: Full-screen luminance boost.
Advanced operation 4.1 OSD menu language About the OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages available for the OSD menu of your Coronis 3MP LED Display. To change the language of the OSD menu: Bring up the OSD main menu.
By enabling the Ethernet over USB, you allow the internal Coronis 3MP LED Display processor to communicate directly over USB with the connected PC. Enabling the Ethernet over USB is only recommended when you are using a non-Barco display controller. If you are using a Barco display controller, this communication will automatically be done over the connected video cable(s).
Enabling the USB endpoint is only recommended when you are using a non-Barco display controller. If you are using a Barco display controller, this communication will automatically be done over the connected video cable(s).
Advanced operation Hibernate can only be enabled on your display when the DPMS mode is enabled first. Therefore, please refer to “DPMS mode”, page 24 to do this. Please connect your keyboard or mouse to your PC rather than to the display's USB ports when hibernate is enabled.
DICOM: DICOM (Digital Imaging and Communications in Medicine) is an international standard that was developed to improve the quality and communication of digital images in radiology. In short, the DICOM display function results in more visible grayscales in the images. Barco recommends selecting the DICOM display function for most medical viewing applications.
Advanced operation Enter the Display Function submenu. Select one of the available display functions and confirm. 4.14 Ambient Light Compensation (ALC) About ALC Ambient Light Compensation (ALC) can only be enabled on your display when the DICOM display function is selected. Therefore, please refer to “Display functions”, page 26 to correctly set the display function.
Embedded QA is not a replacement for the Barco MediCal QAWeb solution. Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still highly recommends MediCal QAWeb as the solution of choice for calibration and QA. Medical QAWeb brings...
Advanced operation 4.17.2 DICOM status report About DICOM status report Following information is available: DICOM Compliance Status (status since last compliance check) • Compliance status: Shows if the current DICOM curve is compliant or not. • Maximum error: Shows the maximum error of the current DICOM curve. This is the deviation compared to a perfect DICOM.
Advanced operation Navigate to the Configuration > Calibration > Embedded QA menu. Select DICOM calibration to start the calibration. Warning: Pressing a key during calibration will abort the calibration, previous values will be restored. Note: After calibration, the compliance check will start automatically. 4.17.5 Reset DICOM calibration About reset DICOM calibration It is possible to restore the original (not corrected) DICOM curve.
Advanced operation 4.19 Display orientation About Display orientation Your display automatically detects its physical orientation (portrait or landscape) and, by default, automatically adjusts the image orientation to this. This means that when your display is physically rotated, the image will rotate along.
Advanced operation HDR2 HDR2 is a Barco specific mode featuring 10-bit video encoding following the High Dynamic Range (HDR) standard but allowing full refresh rate (which is not always possible with HDR1). This mode is usually used on color displays.
Advanced operation 4.23 EDID timings About EDID timings Following EDID timings are available for your Coronis 3MP LED Display: • Refresh Rate: Allows to manually select the refresh rate of the image source video input signal depending on the maximum refresh rate of the display controller connected to your display. •...
Page 34
Advanced operation K5902060 /09 Coronis 3MP LED Display...
Repackaging instructions WARNING: Before repacking the display, follow the instruction to replace the foot protection buffer to prevent damage to the display. K5902060 /09 Coronis 3MP LED Display...
Page 36
Repackaging instructions Overview of the packaging Image 5-1: Packaging Bottom box Box (Power supply, cables) Bottom buffer Top buffer Protection buffer Top box Display Display controller box K5902060 /09 Coronis 3MP LED Display...
Repackaging instructions 5.1 Replacing the protection buffer How to replace the protection buffer Place the display on a stable surface. Put the display in the lowest position and fasten the height mechanism, see “Unlocking the height mechanism”, page 10. Very important: Tilt the panel away from the foot before changing the orientation. Turn the panel counterclockwise to put the panel in landscape orientation, see “Adjusting the display position”, page 10.
Page 38
Repackaging instructions Put the top buffer on top of the display. Slide the top box over the bottom box. Use the three lock bayonets to lock the box. Image 5-3 K5902060 /09 Coronis 3MP LED Display...
Cleaning your display 6.1 Cleaning instructions To clean the display Clean the display using a sponge, cleaning cloth or soft tissue, lightly moistened with a recognized cleaning product for medical equipment. Read and follow all label instructions on the cleaning product. In case of doubt about a certain cleaning product, use plain water.
Important information 7.1 Safety information General recommendations Read the safety and operating instructions before operating the device. Retain safety and operating instructions for future reference. Adhere to all warnings on the device and in the operating instructions manual. Follow all instructions for operation and use. Electrical Shock or Fire Hazard To prevent electric shock or fire hazard, do not remove cover.
Important information Power cords: • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 250 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application. • Do not overload wall outlets and extension cords as this may result in fire or electric shock.
Page 44
Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
“Electronic Information Products Pollution Control Labeling Standard” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “Standard of Electronic Information Products Environmental Friendly Use Period”...
Important information Importers contact information To find your local importer, contact one of Barco’s regional offices via the contact information provided on our website (www.barco.com). FCC class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 47
Important information Electromagnetic environment – Compliance Emissions test Guidance RF emissions Group 1 The Coronis 3MP LED Display uses RF energy only for its internal CISPR 11 function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment.
Page 48
Important information Electromagnetic Immunity test Compliance level IEC 60601 test levels environment – guidance Coronis 3MP LED Display Voltage interruptions: 0% Voltage interruptions: 0% be powered from an residual voltage for 250 residual voltage for 250 uninterruptible power periods at 0° periods at 0°...
Important information 7.5 Explanation of symbols Symbols on the device On the device or power supply, you may find the following symbols (nonrestrictive list): Indicates compliance with Part 15 of the FCC rules (Class A or Class B) Indicates the device is approved according to the UL regulations Indicates the device is approved according to the UL regulations for Canada and US Indicates the device is approved according to the UL regulations for Canada and US E352529...
Page 50
Important information Indicates the legal manufacturer Indicates the manufacturing date Indicates the temperature limitations for the device to safely operate within specs Indicates the device serial number Indicates the device part number or catalogue number Warning: dangerous voltage Caution Consult the operating instructions Indicates this device must not be thrown in the trash but must be recycled, according to the European WEEE (Waste Electrical and Electronic Equipment) directive Indicates Direct Current (DC)
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized.
Important information 7.7 Technical specifications Overview Screen technology UA-SFT (ultra advanced - super fine technology) Backlight Active screen size 540 mm (21.3") (diagonal) Active screen size (H x V) 325 mm x 433 mm (12.8” x 17.1”) Aspect ratio (H:V) Resolution 3MP (2048 x 1536) Pixel pitch...
Page 53
Important information Dot clock 280 MHz OSD languages English, German, French, Dutch, Spanish, Italian, Portugese, Polish, Russian, Swedish, Chinese (simplified), Japanese, Korean, Arabic Dimensions with stand (W x Portrait: 378 x 528~628 x 235 mm H x D) Landscape: 491 x 472~572 x 235 mm Dimensions w/o stand (W x 378 x 491 x 84 mm H x D)
Barco whatsoever. You further acknowledge that any such additions, changes or modifications may impair the ability of Barco – at Barco’s sole discretion - to continue to provide service, warranties, software updates, fixes, maintenance, access or such similar abilities, without any recourse or claim towards Barco whatsoever.
Page 55
Important information K5902060 /09 Coronis 3MP LED Display...