Warnings; Product Description - Nice Spin10KCE Instructions And Warnings For The Fitter

1) Warnings

This manual contains important information regarding safety; before you
start installing the components, it is important that you read all the infor-
mation contained herein. Store this manual safely for future use.
In this manual when all data, warnings and other information related to
all products are stated, the range name "SPIN". The description of indi-
vidual products can be found in chapter "2 Product description"
Considering the hazards that may exist during the installation and oper-
ation of SPIN, installation must be carried out in strict compliance with
current legislation, standards and regulations. This chapter provides
details of general warnings. Other, more specific warnings are detailed in
Chapters "3.1 Preliminary Checks" and "5 Testing and commissioning".
!
According to the most recent European legislation, the
production of automatic doors or gates is governed by the
provisions listed in Directive 98/37/EC (Machine Directive)
and, more specifically, to provisions: EN 12445; EN 12453 and
EN 12635, which enable manufacturers to declare the pre-
sumed conformity of the product.
Please access "www.niceforyou.com" for further information, and guide-
lines for risk analysis and how to draw up the Technical Documentation.
• This manual has been especially written for use by qualified fitters.
Except for the enclosed specification "Instructions and Warnings for
Users of the SPIN gearmotor" which is to be removed by the installer,
none of the information provided in this manual can be considered as
being of interest to end users!
• Any use or operation of SPIN which is not explicitly provided for in
these instructions is not permitted. Improper use may cause damage
and personal injury.

2) Product description

SPIN is a range of gearmotors designed for the automation of sec-
tional doors and, in combination with accessory SPA5 (supplied sep-
arately), protruding or non-protruding spring or counterweight over-
head doors.
Table 1: Description of the SPIN components
Model:
SPIN10KCE
SPIN11KCE
* see paragraph "4.5 radio receiver" for the types of transmitters that can used.
1
Gearmotor Guide
SN6011 3x1m
SN6011 3m
• Risk analysis must be carried out before starting installation, to include
the list of essential safety requisites provided for in Enclosure I of the
Machine Directive, indicating the relative solutions employed. N.B. Risk
analysis is one of the documents included in the "Technical Documen-
tation" for this automation.
• Check whether additional devices are needed to complete the
automation with SPIN based on the specific application requirements
and dangers present. The following risks must be considered: impact,
crushing, shearing, dragging, etc. as well as other general dangers.
• Do not make modifications to any components unless such action is
specified in this manual. Operations of this type are likely to lead to
malfunctions. NICE disclaims any liability for damage resulting from
modified products.
• During installation and use, ensure that solid objects or liquids do not
penetrate inside the control unit or other open devices. If necessary,
please contact the NICE customer service department; the use of
SPIN in these conditions can be dangerous.
• The automation system must not be used until it has been commis-
sioned as described in chapter 5: "Testing and commissioning".
• The packing materials of SPIN must be disposed of in compliance
with local regulations.
• If a fault occurs that cannot be solved using the information provided
in this manual, refer to the NICE customer service department.
• In the event that any automatic switches are tripped or fuses blown,
you must identify the fault and eliminate it before resetting the switch-
es or replacing fuses.
• Disconnect all the power supply circuits before accessing the terminals
inside the SPIN cover. If the disconnection device is not identifiable,
post the following sign on it: "WARNING: MAINTENANCE WORK IN
PROGRESS".
SPIN operates with electric power. In the event of a power failure, the
gearmotor can be released in order to move the door manually.
The products described in tables 1 belong to the SPIN range.
Radio receiver
Incorporated
Incorporated
Radio Transmitter
FLO2R-S*
FLO2R-S*
3
GB