Table of Contents
Advertisement
Quick Links
17,
NETWORK
TECHNOLOGIES
INCORPORATED
KEEMUX-Sx (SUN KVM Switch)
INSTALLATION / USER GUIDE
MAN061
Rev Date 3/30/2001
SUN WORKSTATION
SUN WORKSTATION
SUN WORKSTATION
SUN WORKSTATION
Introduction......................................................................................... 2
Cables
Installation........................................................................................... 2
Keyboard Configuration..................................................................... 3
Cascading
SCAN MODE........................................................................................ 5
BROADCAST MODE........................................................................... 5
Keyboard Updating................................................................. 5
How To Disable Operating Modes............................................. 6
Technical Specifications....................................................................10
Troubleshooting..................................................................................10
Warranty Information..........................................................................10
Tel:330-562-7070
1275 Danner Dr
Fax:330-562-1999
Aurora, OH 44202
NETWORK
17,
TECHNOLOGIES
INCORPORATED
KEEMUX-Sx
2
3
4
5
1
TABLE OF CONTENTS
Cables NOT supplied but required................................................... 2
Introduction....................................................................................... 3
Limitations......................................................................................... 4
Configuration..................................................................................... 4
Cascaded Installation........................................................................ 4
Front Panel Control........................................................................... 5
Keyboard Control.............................................................................. 5
MODE
BROAD
COM
SCAN
CAST
MAND
1 2 3 4 5 6 7 8
ON
OFF
6
7
8
1
SUN WORKSTATION
SUN WORKSTATION
SUN WORKSTATION
SUN WORKSTATION
Advertisement
Table of Contents
Related Manuals for NTI KEEMUX-Sx-O
Summary of Contents for NTI KEEMUX-Sx-O
-
Page 1: Table Of Contents
Installation................... 2 Keyboard Configuration..............3 Cascading Introduction..................3 Limitations..................4 Configuration..................4 Cascaded Installation................ 4 Using the NTI Switch Front Panel Control................5 Keyboard Control................5 SCAN MODE..................5 BROADCAST MODE................5 Keyboard Updating……………………………………………………….. 5 How To Disable Operating Modes……………………………………… 6 Technical Specifications..............10... -
Page 2: Introduction
Connect a cable from the Keyboard port of the computer to a Keyboard port of the NTI switch. Note the port’s number. Connect a cable from the Video port of the computer to the Video port of the NTI switch with the same port number as the keyboard. -
Page 3: Keyboard Configuration
KEYBOARD CONFIGURATION The dip-switches on the front panel are configurable for several tasks. Switches 1-6 are used for cascading actions (see CASCADING section) and switches 7 & 8 are for keyboard configuration. These keyboard configuration switches come pre- configured with switch 7 in the “ON” position and switch 8 in the “OFF” position. You should not change these settings as this will cause your SUN keyboard to not work. -
Page 4: Limitations
1. LIMITATIONS All the slave units must be the same size (4, 8 or 16 port) Up to 8 slave units may be connected to form a maximum system size of 128 ports (1x8 port master + 8x16 port slaves). Slave units must be added to the master unit in order (slave #1 to master’s port 1, slave #2 to master’s port 2, etc). -
Page 5: Using The Nti Switch
KEYBOARD UPDATING Keyboard configuration of each computer is saved in the NTI Switch. For example, if the computer attached to Port 4 had CAPS LOCK and NUM LOCK selected the last time that computer was accessed, then they will automatically be set when that computer... -
Page 6: How To Disable Operating Modes
HOW TO DISABLE OPERATING MODES The three operating modes of the KEEMUX-Sx SUN KVM switch can be disabled if a user desires to do so. The Command Mode can be disabled which would also disable the Scan and Broadcast Modes, or, the Scan and/or Broadcast Modes can be individually disabled leaving the other features in Command Mode enabled. - Page 7 NOTE: Before proceeding, it is important to discharge any static charge you may be carrying by touching any large metal object (away from the KEEMUX-Sx). 4. The first visible circuit board, the uppermost board, is the video board 5 Along the back of the video board are between 3 and 5 video ribbons (depending on how many monitors the unit is designed to connect to) connecting the video board to a circuit board on the rear panel with 15HD connectors on it.
- Page 8 Remove the 4 torx-head screws from the underside as well. These hold the lower circuit board to the plastic case. Turn the KEEMUX-Sx-O back over and set it on a firm and flat surface. Torx-head screws holding in the digital...
- Page 9 Once the desired jumpers are in place, reverse the disassembly process to re-assemble the KEEMUX-Sx (or KEEMUX-Sx-O). Be particularly careful about connecting the ribbons back to the headers they were removed from and to fully insert the ribbons to the headers. Note: The text on the video ribbons (non-OSD version) should face the right-hand side of the case after insertion.
-
Page 10: Technical Specifications
Verify that the computer is connected to a Keyboard port and Video port with the same port number. If the cable from a computer’s Keyboard port is disconnected from the NTI Switch while power is on, turn the power OFF to the computer before plugging the cable back in.