1. Manuals
  2. Brands
  3. Avaya Manuals
  4. Network Router
  5. Secure Router 4134
  6. Hardware installation

Avaya Secure Router 4134 Hardware Installation

Hide thumbs Also See for Secure Router 4134:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual, Manual
Installation — Hardware Components
Avaya Secure Router 2330/4134
Release 10.3.5
NN47263-301
Issue 04.02
August 2013

Advertisement

Table of Contents
loading

Related Manuals for Avaya Secure Router 4134

Summary of Contents for Avaya Secure Router 4134

  • Page 1 Installation — Hardware Components Avaya Secure Router 2330/4134 Release 10.3.5 NN47263-301 Issue 04.02 August 2013...
  • Page 2 Product provided by Avaya including the selection, arrangement and While reasonable efforts have been made to ensure that the design of the content is owned either by Avaya or its licensors and is information in this document is complete and accurate at the time of protected by copyright and other intellectual property laws including the printing, Avaya assumes no liability for any errors.
  • Page 3 See the Avaya Support website: http://support.avaya.com for product notices and articles, or to report a problem with your Avaya product. For a list of support telephone numbers and contact addresses, go to the Avaya Support website: http://support.avaya.com, scroll to the bottom of the page, and select Contact Avaya Support.
  • Page 4 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 5: Table Of Contents

    DS3 Medium Module (supported on Secure Router 4134 only)............37 GbE Medium Module (supported on Secure Router 4134 only)............38 FE and FE/PoE Medium Module (supported on Secure Router 4134 only)........40 Mediation Server Module for OCS (supported on Secure Router 4134 only)........41 Voice Carrier Medium Module (supported on Secure Router 4134 only).........
  • Page 6 Removing the internal PVM......................77 Replacing the DIMM in the Secure Router 4134..................79 Installing or removing the DIMM on the Secure Router 4134 Mediation Server Module for OCS.... 80 Installing a DIMM on the Mediation Server Module................81 Removing a DIMM from the Mediation Server Module..............82 Replacing the Secure Router 4134 internal Compact Flash..............
  • Page 7 DTE RS-530 serial cable........................... 114 DTE RS-530A serial cable........................115 Hardware reliability......................Battery life expectancy on the Mediation Server Module for OCS............119 Translations of safety messages..................Class A device caution statement translations..................121 Qualified service personnel warning statement..................122 Overcurrent warning statement.........................
  • Page 8 Installation — Hardware Components August 2013...

  • Page 9: Chapter 1: Avaya Secure Router 2330/4134 Safety Precautions

    This section provides the information necessary for the proper and safe handling of hardware components for the Avaya Secure Router 2330 and the Secure Router 4134. Please read and apply this information to all aspects of the instructions in this manual.

  • Page 10: Cautions And Warnings For The Secure Router 2330/4134

    The Lithium battery in this product is part of a non-volatile memory device and will retain data for 10 years in the absence of power. Avaya does not consider the lithium battery in this unit a field replaceable or serviceable part and should not be accessed by the customer.

  • Page 11: Foreign Exchange Station (Fxs) Interface Modules

    TIP must connect to TIP and RING must connect to RING. FXS ground start does not work if polarity is reversed. Important: Avaya does not support FXS port connections leaving the building. Use FXS connections for intra-building purposes only. Warning: The 2- and 4-port FXS interface modules have a ring signal generator that is a source of hazardous voltage.

  • Page 12: Foreign Exchange Office (Fxo) Interface Modules

    Personal safety and equipment protection Read this section to prevent injury and equipment damage. Module protection The following practices prevent equipment damage when you work on the Avaya Secure Router 2330/4134: • Always wear a grounded antistatic wrist strap when you handle modules.

  • Page 13: Cables And Connectors Protection

    Personal safety and equipment protection Cables and connectors protection The following practices prevent damage to cables and connectors: • Use caution when connecting cables. Take care to ensure you insert each cable connector in the correct port for the purpose you intend. For example, ensure you connect LAN cables and connectors to LAN ports on the Secure Router 2330/4134.
  • Page 14 Avaya Secure Router 2330/4134 safety precautions Place modules on an appropriate antistatic material when you replace hardware. Use an ESD pad or antistatic packaging. Important: Some antistatic packaging is effective only on the inside of the package. Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 15: Chapter 2: Introduction

    Ongoing product training is available. For more information or to register, you can access the Web site at http://avaya-learning.com. Avaya Mentor videos Avaya Mentor is an Avaya-run channel on YouTube that includes technical content on how to install, configure, and troubleshoot Avaya products. Go to http://www.youtube.com/AvayaMentor...

  • Page 16: Support

    Introduction Support Visit the Avaya Support website at http://support.avaya.com for the most up-to-date documentation, product notices, and knowledge articles. You can also search for release notes, downloads, and resolutions to issues. Use the online service request system to create a service request. Chat with live agents to get answers to questions, or request an agent to connect you to a support team if an issue requires additional expertise.

  • Page 17: Chapter 3: New In This Release

    Chapter 3: New in this release There is no new content added to Avaya Secure Router 2330/4134 Installation — Hardware Components (NN47263–301) for Release 10.3. Installation — Hardware Components August 2013...
  • Page 18 New in this release Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 19: Chapter 4: Avaya Secure Router 2330/4134 Hardware Components Fundamentals

    • 660 W AC (410 W available for PoE) • 250 W DC The Secure Router 4134 has two slots for power supply units. You can install single or dual power supply modules in any of the following configurations: • one or two standard AC input modules •...
  • Page 20 As a general safety precaution, be sure to provide DC power through a circuit breaker on the equipment rack. The following figure shows the AC power supply module for the Secure Router 4134. Figure 1: Secure Router 4134 AC power supply module The following figure shows the DC power supply module for the Secure Router 4134.

  • Page 21: Secure Router 4134 Fan Tray

    While the system power is on, fans in the fan tray never completely stop rotating. You can access the fan tray from the rear panel of the Secure Router 4134. The following figure shows the location of the fan tray in the chassis, and indicates air flow through the chassis.

  • Page 22: Interface Modules For The Secure Router 2330/4134

    • Avaya Secure Router 2330/4134 Configuration — WAN interfaces (NN47263-500) • Avaya Secure Router 2330/4134 Configuration — Layer 2 Ethernet (NN47263-501) Avaya provides the following optional interface modules for the Secure Router 2330/4134: • Small Modules (supported on Secure Router 2330 and 4134):...

  • Page 23: T1/E1 Small Module

    2-port T1/E1 Small Module in either data or voice mode. Important: Slot 2 of the Secure Router 4134 supports only one port of any WAN data Small Module. If you install a 2-port Small Module in Slot 2, and use the Small Module for data connections, one port only is functional (port 1).
  • Page 24 Avaya Secure Router 2330/4134 hardware components fundamentals Figure 5: 2-port T1/E1 Small Module In data mode, the 1-port T1/E1 Small Module provides either one T1 port (supports 24 timeslots with a line data rate of 1.544 Mbps) or one E1 port (supports 31 timeslots with a line data rate of 2.048 Mbps).

  • Page 25: Isdn Bri S/T And Isdn Bri U Small Modules

    Interface modules for the Secure Router 2330/4134 Description • Off: Not connected or the interface is out of service. • Yellow: The interface is in a loopback mode or is running diagnostics • Green: The link or channel is active and receiving a valid signal LINK/STAT 2 Status of interface 2: (applicable to 2-...
  • Page 26 Secure Router 2330/4134 chassis. Important: Slot 2 of the Secure Router 4134 supports only one port of any WAN data Small Module. If you install a 2-port Small Module in Slot 2, and use the Small Module for data connections, one port only is functional (port 1).

  • Page 27: Serial Small Module

    Secure Router 2330/4134 chassis. Important: Slot 2 of the Secure Router 4134 supports only one port of any WAN data Small Module. If you install a 2-port Small Module in Slot 2, and use the Small Module for data connections, one port only is functional (port 1).
  • Page 28 Avaya Secure Router 2330/4134 hardware components fundamentals Figure 8: 1-port Serial Small Module The 2-port Serial Small Module provides two external multiprotocol serial WAN ports. Each port operates in either DTE or DCE mode at data rates up to 2.0 Mbps.
  • Page 29 Interface modules for the Secure Router 2330/4134 Port Connector Recommended Minimum cable Cable length cable type length summary connector EIA-530/A: Up to 11 twisted pairs plus ground to a DB-25 connector Table 7: Maximum DTE cable lengths DTE data rate Maximum DTE cable lengths (kbps) RS-232C...

  • Page 30: Fxs Small Module

    You can install the 2- and 4-port FXS Small Modules in any of the Small Module slots on the Secure Router 2330/4134 chassis. On the Secure Router 4134 chassis, you can also install the FXS Small Modules in the Voice Carrier Medium Module, in any Medium Module slot.
  • Page 31 Interface modules for the Secure Router 2330/4134 Figure 11: 4-port FXS Small Module The following table lists the connectors and cable to use with the 2- and 4-port FXS Small Modules. Table 10: Cable and connectors Port Connector Recommended Minimum cable Loop length cable type length...

  • Page 32: Fxo Small Module

    You can install the 2- and 4-port FXO Small Modules in any of the Small Module slots on the Secure Router 2330/4134 chassis. On the Secure Router 4134 chassis, you can also install the FXO Small Modules in the Voice Carrier Medium Module, which you can install in any Medium Module slot.
  • Page 33 Interface modules for the Secure Router 2330/4134 Figure 13: 4-port FXO Small Module The following table lists the connectors and cable to use with the 2- and 4-port FXO Small Modules. Table 12: Cable and connectors Port Connector Recommended Minimum cable Loop length cable type length...

  • Page 34: T1/E1 Medium Module (Supported On Secure Router 4134 Only)

    • Amber: The interface is configured and ready to use • Green: The interface has an active call T1/E1 Medium Module (supported on Secure Router 4134 only) The 8-port T1/E1 Medium Module provides eight T1 ports (each port supports 24 data timeslots with a line data rate of 1.544 Mbps) or eight E1 ports (each port supports 31 data timeslots...

  • Page 35: Hssi Medium Module (Supported On Secure Router 4134 Only)

    • Yellow: The interface is in a loopback mode or is running diagnostics • Green: The link or channel is active and receiving a valid signal HSSI Medium Module (supported on Secure Router 4134 only) The 1-port High Speed Serial Interface (HSSI) Medium Module provides one external multiprotocol HSSI serial WAN port that operates at up to 52.0 Mbps.

  • Page 36: Ct3 Medium Module (Supported On Secure Router 4134 Only)

    • Yellow: Out of service, or failed to initiate • Green: Power on and the module is operational CT3 Medium Module (supported on Secure Router 4134 only) The 1-port CT3 Medium Module provides a single channelized T3 port operating at 44.736 Mbps for WAN access.

  • Page 37: Ds3 Medium Module (Supported On Secure Router 4134 Only)

    • Yellow: Out of service, or failed to initiate • Green: Power on and the module is operational DS3 Medium Module (supported on Secure Router 4134 only) The 1-port DS3 Medium Module provides a single clear channel T3 port operating at 44.736 Mbps for WAN access.

  • Page 38: Gbe Medium Module (Supported On Secure Router 4134 Only)

    • Yellow: Out of service, or failed to initiate • Green: Power on and the module is operational GbE Medium Module (supported on Secure Router 4134 only) The 10-port 10/100/1000 Ethernet Advanced L2/L3 Medium Module provides ten autonegotiating 10/100/1000 Mbps copper Ethernet ports and two SFP Gigabit Ethernet ports (full duplex).
  • Page 39 Interface modules for the Secure Router 2330/4134 Port Connector Recommended Minimum cable Maximum cable cable type length length (full duplex), operation. EIA 1000Base-T Category 5 UTP (full-duplex) or STP required for 100/1000 Mb/s operation. Fiber ports SFP module Typical SFP None 550 m = 1800 ft Modules:...

  • Page 40: Fe And Fe/Poe Medium Module (Supported On Secure Router 4134 Only)

    The following figures show the 24-port FE and the 24-port FE/PoE Medium Modules. Figure 19: 24-port FE Medium Module Figure 20: 24-port FE/PoE Medium Module Important: You must install the Secure Router 4134 PoE power supply to take advantage of the PoE capabilities. Table 24: Cable and connectors Port...

  • Page 41: Mediation Server Module For Ocs (Supported On Secure Router 4134 Only)

    DIMM memory module, if necessary. You must remove the Mediation Server Module from the Secure Router 4134 to install or remove DIMM memory modules. You can insert or remove a Compact Flash card in the Mediation Server Module with the module installed and running.
  • Page 42 Avaya Secure Router 2330/4134 hardware components fundamentals Figure 21: Mediation Server Module for OCS The following table specifies connectors and recommended cable types and lengths. Table 26: Cable and connectors Port Connector Recommended Minimum cable Maximum cable cable type length...

  • Page 43: Voice Carrier Medium Module (Supported On Secure Router 4134 Only)

    Voice Carrier Medium Module (supported on Secure Router 4134 only) The Voice Carrier Medium Module is a hot swappable module. The Secure Router 4134 supports the following voice-type Small Modules: • 2- and 4-port FXO • 2- and 4-port FXS You can install the supported voice-type Small Modules in any combination in the Voice Carrier Medium Module.
  • Page 44 Avaya Secure Router 2330/4134 hardware components fundamentals The following figure shows the 44-port GbE Large Module. Figure 23: 44-port GbE Large Module This module is oversubscribed and provides a 4:1 blocking ratio. The total available bandwidth at all of the ports (44 Gbps) is four times the available routing bandwidth.

  • Page 45: Adsl2+ Small Module

    Interface modules for the Secure Router 2330/4134 Description • Solid Orange: Link established at 1000 Mbps • Blinking Green or Orange: Receiving or transmitting traffic SFP PORT LEDs are integrated into each port. Status of each interface: STATUS • Off: Link not connected or Link Fail •...
  • Page 46 Avaya Secure Router 2330/4134 hardware components fundamentals Figure 25: 1-port ADSL2+ Annex B Small Module The following table lists the connectors and cables to use with the 1-port ADSL2+ Small Modules. Table 30: Cables and connectors Port Connector Recommended Minimum cable...

  • Page 47: Secure Router 4134 Internal Hardware Components

    The following figure shows the internal hardware components that are field serviceable. For information about locating and removing the service panel to access the internal hardware components, refer to Avaya Secure Router 4134 Installation — Chassis (NN47263-300). Figure 26: Interior of the Secure Router 4134...

  • Page 48: Ddr So-Dimm

    Item Description Caution: Do not open the Secure Router 4134 service access panel while the unit is powered. You cannot hot swap internal components. DDR SO-DIMM The Secure Router 4134 has one SO-DIMM slot. The slot supports a DDR RAM module of either 512 MB or 1 GB.

  • Page 49: Internal Pvm

    Figure 27: Internal VPN/IPSec module Internal PVM You must install the internal PVM in the Secure Router 4134 chassis to use the voice-related modules and features. The following figure shows the PVM in relation to the DDR SO-DIMM. Installation — Hardware Components...

  • Page 50: Internal System Compact Flash

    The PVM is an internal module and is not directly connected to any external interface. Important: You cannot enable the management port on the rear of the Secure Router 4134 (Ethernet 0/0) if you have a PVM installed (this is related to hardware design). Ensure you use Ethernet 0/1, 0/2, 0/3, or 0/4 for management if you use a PVM in the router.

  • Page 51: Hot Swapping Secure Router 4134 Hardware Components

    The following table lists parts that are operator replaceable, as well as the hot swapping capabilities and limitations for each part. Caution: Do not open the Secure Router 4134 service access panel while the unit is powered. Table 33: Hot swapping capabilities for the Secure Router 4134 Component...

  • Page 52: Compatible Internal Modules For Secure Router 2330

    Hot swap Limitations capable VPN/IPSec module Caution: Do not open the Secure Router 4134 service access panel while the unit is powered. Internal compact flash Caution: Do not open the Secure Router 4134 service access panel while the unit is powered.

  • Page 53: Replaceable Parts For Secure Router 2330

    Replaceable parts for Secure Router 2330 This section lists the parts of the Secure Router 2330 that you can replace. A certified Avaya technician must replace any other components or parts. You can hot swap the interface modules without affecting system operation.
  • Page 54 Avaya Secure Router 2330/4134 hardware components fundamentals The following table lists the parts that are operator replaceable, and describes the hot swapping capabilities and limitations for each part. Table 35: Secure Router 2330 replaceable parts Part Hot swap Limitations capable...

  • Page 55: Chapter 5: Installing Avaya Secure Router 2330/4134 Hardware Components

    2330/4134 hardware components The Avaya Secure Router 4134 ships with the fan tray installed, as well as the power supply unit or units that you ordered. This section contains instructions for installing hardware components, as well as instructions for replacing a fan tray, power supply unit, and internal components.
  • Page 56 A slot numbering legend is printed directly above the chassis SFP Ethernet ports (ports 0/3 and 0/4) on the front panel of the Secure Router 4134. The legend shows how slots are numbered on the Secure Router 4134. The following figure shows the slot numbering legend.

  • Page 57: Prerequisites

    • Ensure you have a Phillips #2 screwdriver. Installing a Small Module Use the procedure in this section to install a Small Module in the Secure Router 4134. For instructions to install a Small Module in the VCMM, see Installing a Small Module in the Secure Router 4134 Voice Carrier Medium Module on page 59.

  • Page 58: Installing A Medium Module On The Secure Router 4134

    Installing Avaya Secure Router 2330/4134 hardware components Installing a Medium Module on the Secure Router 4134 Use the instructions in this section to install Medium Modules. Procedure steps 1. Using a Phillips screwdriver #2, remove the slot cover plate from the slot in which you are installing the module.

  • Page 59: Installing A Small Module In The Secure Router 4134 Voice Carrier Medium Module

    Installing a Small Module in the Secure Router 4134 Voice Carrier Medium Module Ensure you securely install the Voice Carrier Medium Module in the Secure Router 4134 chassis before installing Small Modules in the Voice Carrier Medium Module. For instructions...

  • Page 60: Hot Swapping Interface Modules

    Installing Avaya Secure Router 2330/4134 hardware components Electrostatic alert: To prevent damage from electrostatic discharge, always wear an antistatic wrist strap connected to an ESD jack when you work with interface modules. The router does not have an ESD jack—connect the antistatic wrist strap to an ESD jack at your site.
  • Page 61 Important: Avaya recommends that you shut down an operating interface module using the shutdown command before you remove it from the Secure Router 2330/4134 chassis. Traffic on the interface module you are hot swapping is interrupted during the hot swap procedure.

  • Page 62: Connecting Secure Router 2330/4134 Power Cables

    2330/4134 — Troubleshooting (NN47263–700). Connecting Secure Router 2330/4134 power cables There are two types of power supply modules available for the Secure Router 4134: • AC power supply module (standard or PoE) requiring an external AC power source • DC power supply module requiring an external DC power source On the Secure Router 2330, the internal power supply is AC only.

  • Page 63: Connecting Dc Power

    Average time to install one DC power cable: 3 minutes. Electrostatic alert: Always wear an ESD-preventative wrist strap when connecting cables or performing maintenance on a Secure Router 4134. Ensure that the wrist strap makes contact with your skin. Caution: As a general safety precaution, ensure you provide DC power through either a fuse or DC circuit breaker with a maximum rating of 12 amps.
  • Page 64 Installing Avaya Secure Router 2330/4134 hardware components Prerequisites • Ensure you have 18 AWG copper wire with an appropriate terminal (lug). You require two wires for single source power, and four wires for redundant power supplies (that is, two wires for each input).
  • Page 65 Connecting Secure Router 2330/4134 power cables 5. Tighten the –48 V terminal to hold the lug and wire in place. The maximum tightening torque for terminal screws is 9 in-lb (1.02 N-m). 6. Insert the +48 V return lead behind the RTN terminal. 7.

  • Page 66: Connecting The Console Port Cable

    Place the first tie within six inches of the terminal block. Position the bound wires to prevent accidental contact when passing by the Secure Router 4134. 11. Attach the other ends of the leads to a – 48 V DC power source.

  • Page 67: Installing Or Replacing A Secure Router 4134 Power Supply Module

    This procedure does not apply to the Secure Router 2330. The Secure Router 4134 operates with one or two AC power supply modules, one or two DC power supply modules, or one AC and one DC power supply module. You install the power supply modules at the rear of the unit.
  • Page 68 Watch the power supply status LED for alerts if you hot swap a power supply module. Electrostatic alert: To prevent damage from electrostatic discharge, always wear an antistatic wrist strap connected to an ESD jack when performing maintenance on a Secure Router 4134. Ensure that the wrist strap makes contact with your skin. Prerequisites •...

  • Page 69: Replacing A Secure Router 4134 Fan Tray Module

    Caution: This procedure does not apply to the Secure Router 2330. The Secure Router 4134 ships with the fan tray module installed. This section contains instructions for replacing a fan tray module. Average time to install or replace a fan tray module: 1 minute.

  • Page 70: Installing Or Removing The Internal Vpn/Ipsec Module On The Secure Router 4134

    • Ensure the Secure Router 4134 has the power switched off. Procedure steps 1. Remove the two screws at the rear of the Secure Router 4134 that hold the service access panel secure. Remove these two screws only. See the following figure.
  • Page 71 Installing or removing the internal VPN/IPSec module on the Secure Router 4134 2. Slowly slide the access panel toward you until it is clear of the Secure Router 4134. 3. Locate the internal VPN/IPSec module connector slot. 4. Holding the VPN/IPSec module by its edges, align the connector with the slot on the Main Board, pushing down gently, but firmly, to seat the module.

  • Page 72: Removing The Internal Vpn/Ipsec Module

    Procedure steps 1. Remove the two screws at the rear of the Secure Router 4134 that hold the service access panel secure. Remove these two screws only. See the following figure. 2. Slide the access panel toward you until it is clear of the Secure Router 4134.

  • Page 73: Installing Or Removing An Internal Pvm On The Secure Router 4134

    0/0) if you have a PVM installed (this is related to hardware design). Ensure you use Ethernet 0/1, 0/2, 0/3, or 0/4 for management if you use a PVM in the router. If you ordered the PVM with your Secure Router 4134, the Secure Router ships with the PVM installed.

  • Page 74: Installing The Internal Pvm

    • Ensure you have a Phillips #2 screwdriver. Procedure steps 1. Remove the two screws at the rear of the Secure Router 4134 that hold the service access panel secure. Remove these two screws only. See the following figure. 2. Slowly slide the access panel toward you until it is clear of the Secure Router 4134.
  • Page 75 Installing or removing an internal PVM on the Secure Router 4134 4. Ensure the PVM slot is clear of debris. Protective tape is placed over the SO-DIMM and PVM slots during the manufacturing process; remove this tape if it is present.
  • Page 76 Installing Avaya Secure Router 2330/4134 hardware components The release latches close when the PVM is properly installed. See the following figure. Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 77: Removing The Internal Pvm

    • Ensure you have an antistatic bag or sheet available for the PVM that you are removing. Procedure steps 1. Remove the two screws at the rear of the Secure Router 4134 that hold the service access panel secure. Remove these two screws only. See the following figure. Installation — Hardware Components...
  • Page 78 Installing Avaya Secure Router 2330/4134 hardware components 2. Slide the access panel toward you until it is clear of the Secure Router 4134. 3. Locate the PVM. 4. Release the latches that secure the PVM in the slot. There is a release latch at both ends of the PVM slot.

  • Page 79: Replacing The Dimm In The Secure Router 4134

    • Ensure you have a Phillips #2 screwdriver. Procedure steps 1. Remove the two screws at the rear of the Secure Router 4134 that hold the service access panel secure. The following figure shows the two screws that you must remove.

  • Page 80: Installing Or Removing The Dimm On The Secure Router 4134 Mediation Server Module For Ocs

    Mediation Server Module for OCS. The DIMM on the Mediation Server Module is not hot swappable. Average time to replace a DIMM on the Mediation Server Module: 4 minutes. Caution: Do not open the Secure Router 4134 service access panel while the unit is powered. Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 81: Installing A Dimm On The Mediation Server Module

    Installing or removing the DIMM on the Secure Router 4134 Mediation Server Module for OCS Electrostatic alert: To prevent damage from electrostatic discharge, always wear an antistatic wrist strap connected to an electrostatic discharge (ESD) jack when performing maintenance on this product.

  • Page 82: Removing A Dimm From The Mediation Server Module

    Installing Avaya Secure Router 2330/4134 hardware components 4. Locate the DIMM slot on the module. The following figure shows the DIMM slots. 5. If the release latches on each end of the DIMM slot are engaged, release the latches by pushing each latch away from the DIMM slot.
  • Page 83 Installing or removing the DIMM on the Secure Router 4134 Mediation Server Module for OCS Prerequisites • Ensure the Secure Router 4134 is powered down. • Ensure you have a Phillips #2 screwdriver. • Ensure you have an antistatic bag or sheet available for the DIMM that you are removing.

  • Page 84: Replacing The Secure Router 4134 Internal Compact Flash

    Average time to replace the internal Compact Flash: 1 minute Caution: Do not open the Secure Router 4134 service access panel while the unit is powered. Important: The internal Compact Flash that ships with the Secure Router 4134 contains the system image.
  • Page 85 Replacing the Secure Router 4134 internal Compact Flash Procedure steps 1. Remove the two screws at the rear of the Secure Router 4134 that hold the service access panel secure. The following figure shows the two screws that you must remove.

  • Page 86: Removing The Secure Router 2330 Top Cover

    Installing Avaya Secure Router 2330/4134 hardware components Removing the Secure Router 2330 top cover Use the instructions in this procedure to remove the Secure Router 2330 top cover. Prerequisites • Ensure you have a SCIM module ready to install before opening the chassis top cover.

  • Page 87: Installing Or Removing The Internal Scim Module On The Secure Router 2330

    Installing or removing the internal SCIM module on the Secure Router 2330 3. Remove the three screws securing the right-hand side bracket to the chassis and the top cover. 4. Remove the three screws securing the right-hand side of the top cover to the chassis.

  • Page 88: Removing The Internal Scim Module

    Installing Avaya Secure Router 2330/4134 hardware components 4. Using a Phillips screwdriver, tighten the screw that secures the module to the Main Board. Removing the internal SCIM module Use the procedure in this section to remove a SCIM module from the Secure Router 2330.

  • Page 89: Installing Or Removing The Internal Pvim Module On The Secure Router 2330

    Installing or removing the internal PVIM module on the Secure Router 2330 Installing or removing the internal PVIM module on the Secure Router 2330 Use the instructions in this section to install, remove, or replace the internal PVIM module on the Secure Router 2330.

  • Page 90: Removing The Internal Pvim Module

    Installing Avaya Secure Router 2330/4134 hardware components 3. Ensure the PVIM slot is clear of debris. Protective tape is placed over the SO-DIMM and PVIM slots during the manufacturing process; remove this tape if it is present. 4. Holding the PVIM by its edges, insert the module in the slot on the Main Board, pushing down gently, but firmly, to fully seat the module.

  • Page 91: Replacing The Secure Router 2330 Dimm

    Installing or removing the internal PVIM module on the Secure Router 2330 Procedure steps 1. Remove the Secure Router 2330 top cover. For information, see Removing the Secure Router 2330 top cover on page 86. 2. Locate the PVIM module. See the following figure for reference. 3.

  • Page 92: Replacing The Secure Router 2330 Internal Compact Flash

    Installing Avaya Secure Router 2330/4134 hardware components Procedure steps 1. Remove the Secure Router 2330 top cover. For information, see Removing the Secure Router 2330 top cover on page 86. 2. Locate the internal DIMM module. See the following figure for reference.
  • Page 93 Installing or removing the internal PVIM module on the Secure Router 2330 Important: The internal Compact Flash that ships with the Secure Router 2330 contains the system image. Prerequisites • Ensure you have a Phillips #1 screwdriver. • Ensure the Secure Router 2330 is powered off. •...
  • Page 94 Installing Avaya Secure Router 2330/4134 hardware components Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 95: Environmental Requirements

    Environmental requirements The Avaya Secure Router 2330/4134 must operate within the specified tolerance limits shown in the following table. Important: Install the Secure Router 2330/4134 in a restricted-access location. You must limit access to the Avaya Secure Router 2330/4134 to authorized service personnel only. Ensure you allow 2 to 3 feet (0.61 to 0.91 m) of additional clearance around the Secure Router 2330/4134...
  • Page 96 Acoustic noise GR-63-CORE Issue 3, section 4.6 and 5.6 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 97: Interface Connector Pin Assignments

    Interface connector pin assignments The following tables describe Avaya Secure Router 2330/4134 interface connector pin assignments. SFP connector pin assignments are not listed because they are dependent on the specific SFP module that you install. Pins that are not connected are reserved and should not be used.
  • Page 98 — — Unused — — Unused — — Unused Table 42: FXO connector pin assignments (RJ11 interface) Function Not connected (N/C) Ring Table 43: FXS connector pin assignments (RJ11 interface) Function Ring Installation — Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 99 Function Table 44: Serial connector pin assignments for DTE mode signal Signal Direc- DTE mode signal tion RS- 232 RS- 449 RS- 530 V.35 X.21 V.10 V.11 530A TXD+ TXD+ TXD+ TXCE+ TXCE TXCE+ TXCE+ SCTE+ TXC+ TXC+ TXC+ SCT+ RXC+ RXC+ RXC+...
  • Page 100 TXCE– TXCE– SCTE– RXD– SD– TXD– TXD– TD– T– DCD– RR– DCD– DCD– DTR– DM– DSR– DSR– MODE2 In Open Open Open MODE1 In Open Open Open MODE0 In Open Open Open Installation — Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 101 Signal Direc- DCE mode signal tion RS- 232 RS- 449 RS- 530 V.35 X.21 V.10 V.11 530A MODE3 In Open Open Open Open Open Open DSR– TR– DTR– DTR– — Table 46: Serial connector cable type coding Interface type Connector mode pins MODE3 (24) MODE2 (21) MODE1 (22)
  • Page 102 Differential input from network Unused Unused wire pair 2 – Unused Unused wire pair 2 – Table 50: 10/100/1000Base-T connector pin assignments Signal (MDI) Signal (MDI–X) Description BI_DA+ BI_DB+ Data Pair 1 + Installation — Hardware Components August 2013 Comments? infodev@avaya.com...
  • Page 103 Signal (MDI) Signal (MDI–X) Description BI_DA– BI_DB– Data Pair 1 – BI_DB+ BI_DA+ Data Pair 2 + BI_DC+ BI_DD+ Data Pair 3 + BI_DC– BI_DD– Data Pair 3 – BI_DB– BI_DA– Data Pair 2 – BI_DD+ BI_DC+ Data Pair 4 + BI_DD–...
  • Page 104 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 105: Serial Cable Descriptions

    Serial cable descriptions Use this section for specification information about the serial cables available for the Avaya Secure Router 2330/4134. DTE V.35 serial cable Order code: SR0018011E6 Figure 33: DTE V.35 serial cable Table 52: DTE V.35 serial cable description...

  • Page 106: Dce V.35 Serial Cable

    Twisted pair → → DSR CTS 11 12 CTS+ DSR+ Twisted pair ← ← RTS DTR 13 26 LL GND Twisted pair ← — LT GND Shield Shield — Shield A Shield Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 107: Dte X.21 Serial Cable

    DTE X.21 serial cable P1 pin P1 signal Note Direction P2 signal P2 pin RTS– No connect CTS– No connect DTR– No connect MODE2 No connect MODE1 MODE0 MODE3 No connect DSR– No connect DTE X.21 serial cable Order code: SR0018013E6 Figure 35: DTE X.21 serial cable Table 54: DTE X.21 serial cable description P1 pin...

  • Page 108: Dce X.21 Serial Cable

    2 15 TXCE+ Twisted pair → → S+ S– 6 13 TXCE– 5 18 RXD+ RXD– Twisted pair ← ← T+ T– RTS+ RTS– Twisted pair → → I+ I– 5 12 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 109: Dte Rs-449 Serial Cable

    DTE RS-449 serial cable Pin 1 P1 signal Note Direction P2 signal Pin 2 11 10 CTS+ CTS– Twisted pair ← ← C+ C– 3 10 26 Shield — 1 8 Shield TXC+ No connect RXC+ No connect DCD+ No connect DTR+ No connect DSR+...

  • Page 110: Dce Rs-449 Serial Cable

    LL GND 10 19, 20, 37 Shield Shield — Shield 1 Shield MODE2 No connect MODE1 MODE0 No connect MODE3 DCE RS-449 serial cable Order code: SR0018016E6 Figure 38: DCE RS-449 serial cable Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 111: Dte Rs-232 Serial Cable

    DTE RS-232 serial cable Table 57: DCE RS-449 serial cable description P1 pin P1 signal Note Direction P2 signal P2 pin 1 14 TXD+ TXD– Twisted pair → → RD+ RD– 6 24 2 15 TXCE+ Twisted pair → → RT+ RT–...
  • Page 112 TXD– No connect TXCE– No connect TXC– No connect RXC– No connect RXD– No connect DCD– No connect DTR– No connect DSR– No connect MODE2 No connect MODE1 No connect MODE0 MODE3 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 113: Dce Rs-232 Serial Cable

    DCE RS-232 serial cable DCE RS-232 serial cable Order code: SR0018018E6 Figure 40: DCE RS-232 serial cable Table 59: DCE RS-232 serial cable description P1 pin P1 signal Direction P2 signal P2 pin TXD+ → TXCE+ → TXC+ → RXC+ ←...

  • Page 114: Dte Rs-530 Serial Cable

    Twisted pair ← ← ST+ ST– 15 12 4 17 RXC+ RXC– Twisted pair ← ← RT+ RT– 17 9 5 18 RXD+ RXD– Twisted pair ← ← RD+ RD– 3 16 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 115: Dte Rs-530A Serial Cable

    DTE RS-530A serial cable P1 pin P1 signal Note Direction P2 signal P2 pin 6 19 DCD+ DCD– Twisted pair ← ← RR+ RR– 8 10 7 20 DTR+ DTR– Twisted pair → → TR+ TR– 20 23 RTS+ RTS– Twisted pair →...
  • Page 116 DSR+ ← 13 26 LL GND Twisted pair → — LL GND 18 7 Shield Shield — Shield 1 Shield DTR– No connect MODE2 MODE1 MODE0 No connect MODE3 DSR– No connect Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 117: Hardware Reliability

    This average value is calculated from, and based on, a large population of nominally identical items. The following table provides information for the expected reliability of Secure Router 4134 hardware in terms of FIT and MTBF.
  • Page 118 2-port T1/E1 Small Module 484 FITs 2 062 556 hours 2-port ISDN BRI ST Small 582 FITs 1 717 202 hours Module 2-port ISDN BRI U Small 564 FITs 1 771 934 hours Module Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 119: Battery Life Expectancy On The Mediation Server Module For Ocs

    (shutdown time) of the system in which the battery operates. To ensure that the lifetime of the battery is not exceeded, Avaya recommends that you exchange the battery every 4–5 years. Installation — Hardware Components...
  • Page 120 Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 121: Translations Of Safety Messages

    Translations of safety messages Class A device caution statement translations Caution: This device is a Class A product. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users are required to take appropriate measures necessary to correct the interference at their own expense.

  • Page 122: Qualified Service Personnel Warning Statement

    Warning: Aviso Instalação só deve ser executada através de pessoal de serviço qualificado. Leia e siga toda a advertência nota e instruções marcaram no produto ou incluíram na documentação. Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 123: Overcurrent Warning Statement

    Overcurrent warning statement Overcurrent warning statement Warning: The Secure Router 2330/4134 relies on the building installation for overcurrent protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10 A international) is used on the phase conductors. Warning: WARNUNG Nur qualifiziertes Wartungspersonal darf die Installation vornehmen.

  • Page 124: Cover Plate Warning Statement

    Se nello slot non viene installato un modulo, accertarsi di mantenere la copertura in metallo posizionata sullo slot. La rimozione della copertura in metallo ostruisce il flusso d'aria e il raffreddamento appropriato dell'unità. Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

  • Page 125: Power Cord Warning Statement

    Power cord warning statement Power cord warning statement Voltage: Use only power cords that have a grounding path. Without a proper ground, a person who touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the switch may result in excessive emissions.
  • Page 126 Senza un appropriato sistema di messa a terra, le persone che vengono a contatto con l'interruttore corrono il rischio di ricevere scosse elettriche. L'assenza di un percorso per il collegamento a terra dell'interruttore può causare un eccesso di emissioni. Installation — Hardware Components August 2013 Comments? infodev@avaya.com...

This manual is also suitable for:

Secure router 2330

Table of Contents