Related Manuals for REMKO KWK 100-4R
Summary of Contents for REMKO KWK 100-4R
- Page 1 REMKO KWK -4R KWK 100-4R, KWK 150-4R, KWK 250-4R, KWK 400-4R Wall and ceiling chilled/hot water units for heat pump systems Operation · Technology · Spare parts Edition GB – F01...
-
Page 3: Table Of Contents
Contents Safety notes Environmental protection and recycling Transportation and packaging Guarantee Unit description System layout Operation Shutdown Care and maintenance Troubleshooting and customer service Installation Instructions for qualified 10-11 personnel Installation 12-14 Condensate drainage connection Electrical wiring 14-15 Electrical drawings Leak testing Before commissioning Commissioning... -
Page 4: Safety Notes
REMKO is not permitted and make a note of any damage or can cause malfunctions. missing parts on the delivery note. To preclude any risks to persons ■... -
Page 5: Guarantee
(vertical installation) and for ceiling and returned the "guarantee to be cooled into the fin heat installation (horizontal installation). certificate" to REMKO GmbH & exchanger and releases it to the Operation is either individually Co. KG at the time when the unit... -
Page 6: System Layout
REMKO KWK -4R System layout Example of system layout of 2-conductor system (heat pump system) The unit is designed for Indoor area 1 Indoor area 2 Indoor area 3 a 2-conductor system. Chilled/heating water Chilled/heating water Chilled/heating water The 2-conductor system has 2... -
Page 7: Shutdown
Maintenance REMKO GmbH & Co. KG or your We recommend that you take ■ out a maintenance contract contractual partner will be pleased... - Page 8 REMKO KWK -4R Cleaning the filter 7. Carefully insert the filter. Ensure 1. Disconnect the power supply to 8. Switch the power supply and that it fits correctly. the unit. the unit back on. 2. If necessary remove the unit's cover.
-
Page 9: Troubleshooting And Customer Service
Troubleshooting and customer service The unit and components are manufactured using state-of-the-art production methods and tested several times to verify that they function correctly. However, if malfunctions should occur, please check the functions as detailed in the list below. With systems for cooling or heating with indoor units, chillers or heating systems the chapter "Troubleshooting and customer service"... -
Page 10: Installation Instructions For Qualified Personnel
Installation material Minimum clearances (See section "Minimum clearances"). KWK 100-4R to 400-4R Wall installation with ground clearance Do not install the unit in the ■ The indoor unit is attached using immediate vicinity of devices... - Page 11 4. Cut the insulation of the side Installation examples stay plate to accommodate the brass connections on the new KWK 100-4R - 400-4R connection side. Basic unit With foot With air inlet plinth 5. Feed the connections through the newly created holes up to the stop (Fig.
-
Page 12: Installation
REMKO KWK -4R Installation Selecting the hydraulic Unit installation connection Wall installation Ceiling installation 2-conductor cooling system Wall installation without valve The unit is attached by means of The unit is attached by means of ■ assembly: mounting holes in the case while... - Page 13 NOTE NOTE Connection for medium piping The time between being fully The product and safety data open and fully closed can be sheets of the glycol type which The connection of the piping ■ approx. three minutes. is used must be obeyed during by the customer is made on the use and disposal.
-
Page 14: Condensate Drainage Connection
REMKO KWK -4R Electrical wiring Safety valve When operating the unit at ■ outside temperatures below Safety valves limit excess operating CAUTION 0°C, ensure the condensate pressure due to excess warming All electrical installation work drainage line is laid in such a... -
Page 15: Electrical Drawings
Check all plug and terminal Connection terminals connections to verify that they are tight and make a permanent contact. Tighten as required. Electrical drawings KWK 100-4R to 400-4R Legend Power supply 230V, 1~, 50Hz Level 3 = white = green... -
Page 16: Before Commissioning
REMKO KWK -4R Before commissioning Commissioning Anti-freeze protection for the Function test of heating operating medium mode Commissioning should only be ■ If a water-glycol mixture is used, performed and documented by 1. Switch the power supply it is to be pre-mixed before being specially trained personnel. -
Page 17: Unit Dimensions
Unit dimensions KWK 100-4R to 400-4R Cooling / heating inlet Cooling / heating outlet 100- 150- 250- 400- 1110 All information in mm Exploded view of the units KWK 100-4R to 400-4R Spare parts list Designation KWK 100-4R KWK 150-4R... -
Page 18: Technical Data
REMKO KWK -4R Technical data Series KWK 100-4R KWK 150-4R KWK 250-4R KWK 400-4R Operating mode Chilled/hot water units for wall and ceiling mounting, 2-conductor version 1.18 1.59 2.21 2.73 Nominal cooling output Nominal cooling output, sensitive 0.93 1.23 1.70 2.08... -
Page 19: Services
Services Cooling capacity Unit Air inlet 7 /12°C 10 /15°C 14/19°C 18/21°C Flow Noise volume pressure power TK 27°C, FK19°C Level dB(A) dB(A) [l/h] [kW] [kW] [l/h] [kW] [kW] [l/h] [kW] [kW] [l/h] [kW] [kW] [l/h] 25.5 0.83 0.63 141.8 0.53 0.53 14.6... - Page 20 This has given us the reputation of being more than just an excellent, reliable supplier: REMKO, a partner who helps to solve problems. Sales REMKO offers not just a well- established sales network both...