Advertisement
Quick Links
Advertisement
Related Manuals for GABOR TM-1732
Summary of Contents for GABOR TM-1732
- Page 1 TM-1732 / TILTING WALL MOUNT For 17 - 32 Flat Panel Screens ” ” User Manual...
- Page 2 Thank you for choosing Gabor. Thank you for choosing Gabor’s tilting flat panel screen wall mount. This heavy-duty wall mount has been engineered to provide your 17”-32” flatscreen monitor with sturdy, long-lasting support that can be relied upon for years of viewing enjoyment.
- Page 3 Welcome...
-
Page 4: Tools Required For Installation
Tools Required For Installation Product Specifications 1. Power Drill 3. Tape Measure 2. Phillips Screwdriver 4. Socket Wrench • For Mounting 17”-32” Flat Panel Screens On Wooden Studs & Concrete Walls Product Contents • VESA Mounting Supplied Parts & Hardware Pattern A M4 Washer H M6 Spacer... - Page 5 Mounting Bracket Bolt/Anchor/Spacer A ×4 D ×4 F ×4 H ×4 J ×3 B ×4 E ×4 G ×4 I ×4 O ×3 C ×4 Contents...
-
Page 6: Safety Warnings
8 When installing this product, be sure professional or installation contractor; directly to center of wooden wall to refer to mounting instructions Gabor takes no responsibility for studs or on a solid concrete wall detailed in this manual; failure to any product damage or personal... - Page 7 STEP 1: • Measure distance from • For a simpler calculation, Aligning Mount seating area to viewing cut a piece of sturdy Correctly On Wall area to determine proper cardboard that’s placement. The ideal approximately the same • The optimal height to position should place size as flatscreen device position a flatscreen...
- Page 8 STEP 2: Positioning Mounting Bracket Directly On Wall insert bolts through • Remove wall mount • After confirming height large mount holes and from bolts and proceed positioning is appropriate verify that they can to Step 3. by marking wall with a slide downwards into pencil, hold wall mount smaller hole areas found...
- Page 9 Wall-Type Mounting Details Mounting To Mounting To Solid Wood Studs Under Concrete Wall: Sheetrock Wall: Pre-drill holes according Pre-drill holes according to markings on wall with to markings on wall with a 12.7mm drill bit; be sure a 3mm drill bit; be sure pre-drilled holes are at pre-drilled holes are at least 60mm deep;...
-
Page 10: Installation Instructions
Installation Instructions STEP 3: Installing • Continue by aligning and model of flatscreen Mounting Bracket On bracket extenders with device. Rear Of Flatscreen hole pattern on rear of • Use the shortest flatscreen device, while • Begin by fastening all configuration of bolts, ensuring that device 4 bracket extenders to... - Page 11 Installation Instructions...
- Page 12 Hardware Configurations For Display For Display With Curved Backs & With Flat Back: Recessed Mountings: Install bracket directly to Install appropriate sized flatscreen device using only spacer between bracket bolts and square washers and flatscreen device; provided; align bolt with then fasten securely with proper sized hole on bolts and washers.
- Page 13 STEP 4: Installing Wall Mount To Wall • With flatscreen device fully attached to mount, slide larger wall mount holes over all 3 bolts on wall and allow it to slide down into smaller holes found above; then ensure it holds securely. •...
- Page 14 Customer ONE-YEAR LIMITED WARRANTY: Support This GABOR product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year For more information or from the original purchase date or thirty (30) days after replacement, whichever occurs later.
- Page 15 Customer Support / Warranty...
- Page 16 MADEBYGABOR WWW. .COM...
Need help?
Do you have a question about the TM-1732 and is the answer not in the manual?
Questions and answers