Subscribe to Our Youtube Channel
Related Manuals for GABOR MD-BSL15W
Summary of Contents for GABOR MD-BSL15W
- Page 1 MD-BSL15W / SPRING-LOADED TWIN-ARM MONITOR MOuNT For 15″–27″ (38.1–68.6 cm) LCD desktop computer User Manual...
- Page 2 Thank you for choosing Gabor. The Gabor MD-BSL15W mounts two 15″–27″ (38.1–68.6 cm) LCD computer monitors side by side. It attaches to the edge of your desk via a built-in clamp, freeing up valuable desk space and enabling personalized monitor placement for improved safety and comfort over conventional monitor stands.
- Page 3 Welcome...
-
Page 4: Installation
Overview Mounting Arm (x2) Shaft cap VESA mount Support bracket Mounting pegs Mounting socket Set screw Locking collar Shaft Cable guides Clamp screws Clamp Tools Required For Installation Clamp locking knob • Phillips screwdriver Overview... - Page 5 Also Included M4x12 (x8) M4x30 (x8) M4x12 (x8) M4x30 (x8) Supplied Parts & Hardware A (8) M4×12 screws E 5 mm hex key I Shaft cap (x1) (x1) S=3mm S=5mm B (8) M4×30 screws F (8) Spacers J User manual (x1) (x1) S=3mm...
- Page 6 Product Specifications Max. 28.7” (73 cm) • Monitor display size: 90° 15″—27″ (38.1–68.6 cm) 360° 90° • Maximum load capacity (per arm): 17 lb. (7.8 kg) 360° 180° 180° • VESA standards: 75×75, 100 × 100 85° • Tilt: -90°/+85° 85°...
-
Page 7: Safety Warnings
Safety Warnings Please read and follow these instructions Do not exceed the maximum load capacity. and keep this manual in a safe place. Do not install this product on an unsteady Clean this product with only a soft, dry cloth. structure or one that is prone to vibration, has a chance of being impacted, or is susceptible to other movements. -
Page 8: Getting Started
The like this one, position your MW-C wall mount offers an alternative mounting option for primary monitor directly your MD-BSL15W dual-monitor setup. in front of you, and your secondary monitor to the side. You shouldn’t need to... - Page 9 If your desk is close to 2. Fit the clamp over the a wall or you don’t have edge of your desk, and • The MD-BSL15W easily enough clearance to fit tighten the clamp locking attaches to most desk the entire clamp behind knob until the shaft is edges up to 2.6″...
- Page 10 Limited Clearance 4. Reinsert the clamp screws and use the 1. Use the included 5 mm included 5 mm hex key hex key to remove the to fasten them until fully clamp screws. tightened. 2. Fit the top part of the 5.
- Page 11 Adjusting the 3. Slide the support bracket along the shaft so it Support Bracket rests on the locking collar, 1. Rotate the locking collar and use the included 3 to loosen it, and then mm hex key to fasten slide the collar to the the set screw until fully approximate height at tightened.
- Page 12 Attaching Your Monitor to the VESA Mounts Before attaching your monitor to the VESA mount, you may need to detach your monitor’s built-in stand. For information on how to do this, consult your monitor’s user manual. Depending on how the back of your monitor is configured, you can use one of two methods to install the VESA mount onto your monitor: flush or recessed.
-
Page 13: Flush Installation
Flush Installation Note: Before starting, Repeat these or the other 2. Align the mounting make sure the VESA mount, holes in the VESA mount set of installation steps as mounting arm, and monitor with the corresponding necessary for your second are facing the proper mounting holes in monitor and continue to... -
Page 14: Recessed Installation
Recessed Installation Note: Before starting, Tip: Thread each of the 2. Place four of the included make sure the VESA spacers on each of your screws by hand before mount, mounting arm, and monitor’s four VESA fastening them with the monitor are facing the proper mounting holes. - Page 15 Mounting the Arms 3. Thread one of the included 5. Insert your monitor cable 1. Lift the arm/monitor M6x25 assembly and mount it protective caps onto the into the cable guides on the onto one of the mounting screw as much as possible, underside of the mounting pegs on the aluminum and then push the cap into...
- Page 16 Adjusting Tension and Articulation Note: Arm Tension To prevent your monitors To avoid damage, make from drooping, you can adjust Important! The arm tension sure to hold your monitor the tension of the mechanical is preset for lighter monitors. steady when making any spring in the mounting arms.
- Page 17 Arm Swivel Monitor Tilt and Swivel You can adjust the arms’ (horizontal) swivel You can adjust the (vertical) tilt and action via the set screws on the rear of the (horizontal) swivel action of your monitors mounting sockets. Position the arms as for optimal viewing comfort.
-
Page 18: Customer Support
Customer ONE-YEAR LIMITED WARRANTY: Support This GABOR product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year For more information or from the original purchase date or thirty (30) days after replacement, whichever occurs later. - Page 19 Customer Support / Warranty...
- Page 20 MADEBYGABOR WWW. .COM...
Need help?
Do you have a question about the MD-BSL15W and is the answer not in the manual?
Questions and answers