Panasonic AW-RP501 Service Manual page 7

When the switch is in the MANU position, the iris can be
manually controlled over the range from the closed posi-
tion to the fully open position using IRIS LEVEL Control
@6 .
Set the switch to the MANU position in storing iris data
in PRESET Switches @8 with MEMORY Switch @7 . If
the switch is in the AUTO position, iris data will not be
stored in the memory.
@6 Lens Iris Control [IRIS, LEVEL]
When IRIS AUTO/MANU Switch @5 is in the MANU
position, the iris can be controlled over the range from
the closed position to the fully open position using this
control. Turning it clockwise opens the iris and turning it
counterclockwise closes the iris.
If the camera is preset to AUTO IRIS ADJ ON when
IRIS AUTO/MANU Switch @5 is in the AUTO position,
this control may be used for fine adjustment of ALC
focus level. For details, refer to the Operating
Instructions for the Camera.
If the preset memory is called by pressing PRESET
Switches @8 when IRIS AUTO/MANU Switch @5 is in the
MANU position, the iris is adjusted to the preset value
stored in the memory regardless of the position of this
control. If the control is turned after that, the iris is
adjusted corresponding to the position of the control.
@7 Preset Memory Switch [MEMORY]
Head pan/tilt positions, lens zoom/focus/iris (provided
that IRIS AUTO/MANU Switch @5 is in the MANU posi-
tion), and camera white balance (ATW Channel A or B)
can be preset in up to 10 memory buttons.
To preset them in these buttons, first select a head
pan/tilt position, lens zoom/focus/iris, or camera white
balance (ATW or Channel A or B); press MEMORY
Switch @7 (so it lights yellow green and all the 10 but-
tons of PRESET Switches @8 flash); while keeping the
MEMORY Switch @7 depressed, press one of the 10
buttons of PRESET Switch @8 as desired. The pressed
button in which the selected item is stored lights.
@8 Preset Position Selection Switches [PRESET]
The head pan/tilt positions, lens zoom/focus/iris, and
camera white balance that are stored in the buttons of
PRESET Switch @8 can be recalled to operate the
pan/tilt head, the lens, and the camera according to the
preset data.
To preset them in the PRESET switches, first select a
head pan/tilt position, lens zoom/focus/iris, or camera
white balance (ATW or Channel A or B); press the
MEMORY Switch @7 (so it lights yellow green and all the
10 buttons of PRESET Switches @8 flash); at the same
time press one of the 10 buttons of PRESET Switches
@8 as desired. The pressed button in which the selected
item is stored lights.
@9 Speed Selection Switch [SPEED]
If ZOOM lever #6 , FOCUS Lever #7 , or PAN/TILT Lever
#8 is moved while keeping SPEED Switch @9
depressed, the corresponding operation takes place at
low speed, provided that SPEED SW CHANGE Switch
%0 is in the LOW position. If one of these levers is
moved with SPEED Switch @9 depressed when SPEED
SW CHANGE Switch %0 is in the HIGH position, the cor-
responding operation takes place at high speed.
SPEED Switch @9 remains lit while it is kept depressed.
#0 Defroster Switch [DEF, ON/OFF]
If this switch is connected to a pan/tilt head with a built-
in defroster function, it switches on and off the defroster.
#1 Wiper Switch [WIP, ON/OFF]
If this switch is connected to a pan/tilt head with a built-
in wiper function, it switches on and off the wiper.
#2 Heater/Fan Switch [H/F, ON/OFF]
If this switch is connected to a pan/tilt head with a built-
in heater or fan function, it switches on and off the
heater or fan.
#3 Lens Extender Switch [EXT, ON/OFF]
If this switch is connected to a lens with a built-in exten-
der function, it switches on and off the lens extender.
For details, refer to the Operating Instructions for the
Lenses and Pan/tilt Head.
#4 ND Filter Switch [ND, ON/OFF]
If this switch is connected to a lens with a built-in ND fil-
ter function, it switches on and off the ND filter. For
details, refer to the Operating Instructions for the Lenses
and Pan/tilt Head.
4