Panasonic AW-RP501 Service Manual page 15

@9 Speed Selection Switch [SPEED]
If ZOOM lever #6 , FOCUS Lever #7 , or PAN/TILT Lever
#8 is moved while keeping SPEED Switch @9
depressed, the corresponding operation takes place at
low speed, provided that SPEED SW CHANGE Switch
$9 is in the LOW position. If one of these levers is
moved with SPEED Switch @9 depressed when SPEED
SW CHANGE Switch $9 is in the HIGH position, the cor-
responding operation takes place at high speed.
SPEED Switch @9 remains lit while it is kept depressed.
#0 Defroster Switch [DEF, ON/OFF]
If this switch is connected to a pan/tilt head with a built-
in defroster function, it switches on and off the defroster.
Note: At the same time as a pan/tilt head is selected
with CONTROL Switch @2 , the defroster of the
selected pan/tilt head is switched on or off depend-
ing on the position of DEF ON/OFF Switch #0 .
#1 Wiper Switch [WIP, ON/OFF]
If this switch is connected to a pan/tilt head with a built-
in wiper function, it switches on and off the wiper.
Note: At the same time as a pan/tilt head is selected
with CONTROL Switch @2 2 , the wiper of the selected
pan/tilt head is switched on or off depending on the
position of WIP ON/OFF Switch #1 .
#2 Heater/Fan Switch [H/F, ON/OFF]
If this switch is connected to a pan/tilt head with a built-
in heater or fan function, it switches on and off the
heater or fan.
Note: At the same time as a pan/tilt head is selected
with CONTROL Switch @2 2 , the heater or fan of the
selected pan/tilt head is switched on or off depend-
ing on the position of H/F ON/OFF Switch #2 .
#3 Lens Extender Switch [EXT, ON/OFF]
If this switch is connected to a lens with a built-in exten-
der function, it switches on and off the lens extender.
For details, refer to the Operating Instructions for the
Lenses and Pan/tilt Head.
Note: At the same time as a pan/tilt head is selected
with CONTROL Switch @2 2 , the lens extender of the
selected pan/tilt head is switched on or off depend-
ing on the position of EXT ON/OFF Switch #3 .
#4 ND Filter Switch [ND, ON/OFF]
If this switch is connected to a lens with a built-in ND fil-
ter function, it switches on and off the ND filter. For
details, refer to the Operating Instructions for the Lenses
and Pan/tilt Head.
Note: At the same time as a pan/tilt head is selected
with CONTROL Switch @2 2 , the ND filter of the select-
ed pan/tilt head is switched on or off depending on
the position of ND ON/OFF Switch #4 .
#5 Option Switch [OP, ON/OFF]
Controls the option switch terminal on the Pan/tilt Head
AC Adapter (AW-PS300) to short circuit or open it. That
is, the option switch terminal is shorted when OP
ON/OFF Switch #5 is in the ON position, or is opened
when it is in the OFF position. For details, refer to the
Operating Instructions for the Pan/tilt Head AC Adapter.
Note: At the same time as a pan/tilt head is selected
with CONTROL Switch @2 2 , the option switch terminal
on the selected pan/tilt head is shorted or opened
depending on the position of OP ON/OFF Switch #5 .
#6 Zoom Lever [ZOOM, TELE/WIDE]
Used to control the zoom operation of the lens that is
connected to the pan/tilt head selected with CONTROL
Switch @2 2 . Zoom speed varies according to the angle of
the lever. The lens moves toward TELE when the lever
is moved toward TELE, or toward WIDE when the lever
is moved toward WIDE, provided that ZOOM REVERSE
Switch %0 is in the NOR position.
REVERSE Switch %0 is set to the REV position, the lens
moves in the opposite direction.
EXCHANGE Switch %1 may be used to exchange its
function with FOCUS Lever #7 .
#7 Focus Lever [FOCUS FAR/NEAR]
Used to adjust the focus of the lens that is connected to
the pan/tilt head selected with CONTROL Switch @2 2 .
Used to adjust the lens focus at varying speed depend-
ing on the angle of the lever. The lens is focused far
when the lever is moved toward FAR, or near when the
lever is moved toward NEAR, provided that FOCUS
REVERSE Switch %2 is in the NOR position. When
FOCUS REVERSE Switch %2 is set to the REV position,
the lens focus operates in the opposite direction.
ZOOM/FOCUS EXCHANGE Switch %1 may be used to
exchange its function with ZOOM Lever #6 .
#8 Pan/tilt Lever [PAN/TILT, UP/DOWN/LEFT/RIGHT]
Used to control the pan/tilt operation of the pan/tilt head
selected with CONTROL Switch @2 2 . Controls the head's
pan/tilt operation at varying speed depending on the
angle of the lever. The pan/tilt head turns up when the
lever is moved toward UP, or down when it is moved
toward DOWN, provided that TILT REVERSE Switch %3
is in the NOR position.
12
When ZOOM
ZOOM/FOCUS