Panasonic AW-RP501 Service Manual page 14

@2 Camera/Pan/tilt Head Selection Switch [CONTROL]
Select a desired camera with pan/tilt head from among
those connected to the control panel. When a camera
with pan/tilt head is selected by pressing one of the but-
tons [1] to [5], the pressed button lights.
Note: Even if an unconnected camera with pan/tilt head
is selected by pressing the corresponding button,
the button lights.
@3 Lamp Indicator [LAMP]
Lights red when LAMP ON/OFF Switch @4 is in the ON
position. Flashes if the lamp connected to the AC
adapter (AW-PS300) for the pan/tilt head selected with
CONTROL Switch @2 is broken. Goes out when LAMP
ON/OFF Switch @4 is set to the OFF position.
Caution: In connecting a halogen lamp to the Pan/tilt
Head AC Adapter (AW-PS300), make sure that it is
in the wattage range of 250 to 500W. If a halogen
lamp less than 250W is used, the LED may flash
when LAMP ON/OFF Switch @4 is in the on position
even if the lamp is normal.
@4 Lamp Switch [LAMP, ON/OFF]
Switches on and off the halogen lamp connected to the
lamp AC receptacle of the Pan/tilt Head AC Adapter
(AW-PS300). Select a pan/tilt head with CONTROL
Switch @2 , then switch the halogen lamp on or off as
necessary. Set it to the ON position to switch the halo-
gen lamp on (in which case, the lamp Indicator flashes).
Set it to the OFF position to switch the halogen lamp off.
Note: When a pan/tilt head is selected with CONTROL
Switch @2 , the halogen lamp connected to the AC
adapter for the pan/tilt head selected with that
switch lights or goes out depending on the position
of LAMP ON/OFF Switch @4 .
@5 Lens Iris Selection Switch [IRIS, AUTO/MANU]
Used to select AUTO or MANU mode in adjusting the
lens iris connected to the selected camera and pan/tilt
head. When this switch is in the AUTO position, the
lens iris is automatically controlled according to the
quantity of light entering the lens. When the switch is in
the MANU position, the iris can be manually controlled
over the range from the closed position to the fully open
position using IRIS LEVEL Control @6 .
Set the switch to the MANU position in storing iris data
in PRESET Switch @8 with MEMORY Switch @7 . If the
switch is in the AUTO position, iris data will not be
stored in the memory.
@6 Lens Iris Control [IRIS, LEVEL]
When IRIS AUTO/MANU Switch @5 is in the MANU posi-
tion, the iris can be controlled over the range from the
closed position to the fully open position using this con-
trol. Turning it clockwise opens the iris and turning it
counterclockwise closes the iris.
If the camera is preset to AUTO IRIS ADJ ON when IRIS
AUTO/MANU Switch @5 is in the AUTO position, this
control may be used for fine adjustment of ALC focus
level. For details, refer to the Operating Instructions for
the Camera.
If the preset memory is called by pressing PRESET
Switch @8 when IRIS AUTO/MANU Switch @5 is in the
MANU position, the iris is adjusted to the preset value
stored in the memory regardless of the position of this
control. If the control is turned after that, the iris is
adjusted corresponding to the position of the control.
@7 Preset Memory Switch [MEMORY]
Head pan/tilt positions, lens zoom/focus/iris (provided
that IRIS AUTO/MANU Switch @5 is in the MANU posi-
tion), and camera white balance (ATW, Channel A or B)
can be preset in up to 10 memory buttons per pan/tilt
head.
To preset them in these buttons, first select a camera
and pan/tilt head with CONTROL Switch @2 2 , then select
a head pan/tilt position, lens zoom/focus/iris, or camera
white balance (ATW Channel A or B); press MEMORY
Switch @7 (so it lights yellow green and all the 10 buttons
of PRESET Switch @8 flash); while keeping the MEMO-
RY Switch @7 depressed, press one of the 10 buttons of
PRESET Switch @8 ) as desired. The pressed button in
which the selected item is stored lights.
@8 Preset Position Selection Switch [PRESET]
The head pan/tilt positions, lens zoom/focus/iris, and
camera white balance that are stored in the buttons of
PRESET Switch @8 can be recalled to operate the
pan/tilt head, the lens, and the camera according to the
preset data.
To preset them in the PRESET switches, first select a
camera and pan/tilt head with CONTROL Switch @2 ,
then select a head pan/tilt position, lens zoom/ focus/iris,
or camera white balance (ATW Channel A or B); press
the MEMORY Switch @7 (so it lights yellow green and all
the 10 buttons of PRESET Switch @8 flash); at the same
time press one of the 10 buttons of PRESET Switch @8
as desired. The pressed button in which the selected
item is stored lights.
11