Panasonic AW-RP501 Service Manual page 2

This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
[AW-RP505]
Source Voltage :
Power Consumption :
Preview Video Input :
Genlock Input :
Preview Video Output :
Genlock Output :
Camera Control Output :
Pan/tilt Control Output :
System Tally Input :
Auxiliary Control Input :
Switches :
Controls :
Multiport Hub Connecting
Cable :
Maximum cable length :
Operating temperature :
Dimensions :
Weight :
Finish :
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
ACCESSORIES
Seal ........................................................ 1
Rack angle .............................................. 2
Connect plate.......................................... 1
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
IMPORTANT SAFETY NOTICE
here are special components used in this equipment which are important for safety. These parts are indicated
T
by the " Y " mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
12 V DC (DC jack)
12 V, 0.5 A
1.0 V[p-p] composite/75Ω (BNC connector)
black burst
75Ω loop through with auto terminator (BNC connector)
1.0 V[p-p] composite/75Ω (BNC connector)
75Ω (BNC connector)
Control signal (BNC connector)
Control signal (RJ-45 8P modular jack)
Tally signal (6 pin Terminal block)
Control signal (8 pin DIN connector)
Power ON/OFF Switch, CAM CONT Switch, GAIN HIGH/MID/LOW Switch,
GAIN AGC/MANU Switch, SCENE FILE Switch, CONTROL Switch, LAMP Switch,
MODE BAR/CAM Switch SHUTTER Switch, AUTO/ATW ATW Switch, AUTO/ATW A Switch,
AUTO/ATW B Switch, AWC Switch, ABC Switch, G/L PHASE ON/OFF Switch,
G/L PHASE Coarse Switch, IRIS AUTO/MANU Switch, MEMORY Switch, PRESET Switch,
DEF Switch, WIP Switch, H/F Switch, EXT Switch, ND Switch, OP Switch, SPEED Switch,
T. PED Control, G/L PHASE SC Control, G/L PHASE H Control, IRIS LEVEL Control,
ZOOM Lever, FOCUS Lever, PAN/TILT Lever
x 4 (Coaxial Cable 3 pcs., 10BASE-T straight cable 1 pc.)(In case of using G/L function)
10 m (In case of using coaxial cables 5C-2V and 10BASE-T straight cable UTP category-5)
−10°C to +45°C (14°F to +113°F)
210 (W) x 88 (H) x 177 (D) mm [8-1/4" (W) x 3-1/2" (H) x 7" (D)]
2.2 kg (4.9 lbs.)
AV Ivory painting
WARNING
!
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that impotant literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
Mounting screws ......................................... 12
M4 x 8mm .............................................. 8
M5 x 8mm .............................................. 4