Panasonic AW-RP501 Service Manual page 10

Front Panel
%0 0 Speed Switch Changing Switch
[SPEED SW CHANGE, LOW/HIGH]
Changes the polarity of SPEED Switch @9 . If ZOOM
lever #6 , FOCUS Lever #7 , or PAN/TILT Lever #8 is
moved while keeping SPEED Switch @9 depressed, the
corresponding operation takes place at low speed, pro-
vided that SPEED SW CHANGE Switch %0 is in the
LOW position. If one of these levers is moved with
SPEED Switch @9 depressed when SPEED SW
CHANGE Switch %0 is in the HIGH position, the corre-
sponding operation takes place at high speed.
The speed polarity can also be changed by pressing
SPEED Switch @9 while keeping MEMORY Switch @7
depressed. When this step is taken again, the original
speed polarity is restored. Take this step if it is difficult
to shift SPEED SW CHANGE Switch %0 because this
control panel is mounted on a console or the like.
%1 Zoom Reverse Switch
[ZOOM REVERSE, NORM/REV]
Changes the operating direction of ZOOM Lever #6 .
The lens zoom moves toward TELE when ZOOM Lever
#6 is moved toward TELE, or toward WIDE when it is
moved toward WIDE, provided that ZOOM REVERSE
Switch %1 is in the NOR position.
REVERSE Switch %1 is set to the REV position, lens
zoom operation takes place in the opposite direction.
With ZOOM REVERSE Switch %1 in the REV position,
the operating directions shown on the panel are
reversed. In this case, paste the supplied seal on the
panel.
%2 Zoom/Focus Exchange Switch
(ZOOM/FOCUS EXCHANGE, ON/OFF]
ZOOM Lever #6 and FOCUS Lever #7 exchange their
function between them when this switch is set to the ON
position. Unless this exchange is needed, keep the
switch in the OFF position.
S P E E D . S W Z O O M Z O O M / F O U C U S
C H A N G E R E V E R S E E X C H A N G E
L O W H I G H N O R R E V O F F O N
%0 %1 %2 %3
When ZOOM
F O U C U S T I LT PA N
R E V E R S E R E V E R S E R E V E R S E
N O R R E V N O R R E V N O R R E V
%4 %5
With ZOOM/FOCUS EXCHANGE Switch %2 in the ON
position, the operations shown on the panel do not
agree with the indications on the panel. In this case,
paste the supplied seal on the panel.
%3 Focus Reverse Switch
[FOCUS REVERSE, NOR/REV]
Changes the operating direction of FOCUS Lever #7 .
The lens is focused far when FOCUS Lever #7 is moved
toward FAR, or near when the lever is moved toward
NEAR, provided that FOCUS REVERSE Switch %3 is in
the NOR position. When FOCUS REVERSE Switch %3
is set to the REV position, the lens focus operates in the
opposite direction.
With FOCUS REVERSE Switch %3 in the REV position,
the operating directions shown on the panel are oppo-
site to the indications on the panel. In this case, paste
the supplied seal on the panel.
%4 Tilt Reverse Switch [TILT REVERSE, NOR/REV]
Changes the tilt direction controlled by PAN/TILT Lever
#8 . The pan/tilt head turns up when PAN/TILT Lever #8
is moved toward UP, or down when it is moved toward
DOWN, provided that TILT REVERSE Switch %4 is in
the NOR position. The pan/tilt head moves in the oppo-
site direction if the TILT REVERSE Switch %4 is in the
REV position.
With TILT REVERSE Switch %4 in the REV position, the
operating directions shown on the panel are opposite to
the indications on the panel. In this case, paste the sup-
plied seal on the panel.
%5 Pan Reverse Switch [PAN REVERSE, NOR/REV]
Changes the pan direction controlled by PAN/TILT
Lever #8 .
PAN/TILT Lever #8 is moved toward LEFT, or rightward
if it moved toward RIGHT.
7
The pan/tilt head turns leftward when