Panasonic AW-RP501 Service Manual page 5

u Electronic Shutter Speed Selection Switch
[SHUTTER, ELC/ 1/100 /OFF]
Used to select a mode of camera electronic shutter con-
trol. With the switch in the ELC position, the electronic
shutter is controlled and the camera sensitivity is auto-
matically adjusted when using the camera in a bright
place. The shutter speed is 1/100 second when the
switch is in the 1/100 position. The electronic shutter is
off when the switch is in the OFF position.
i White Balance ATW Selection Switch
[AUTO/ATW, ATW]
When the switch is depressed, the camera keeps auto-
matically adjusting white balance.
when it is selected.
o White Balance Ach Selection Switch
[AUTO/ATW, A]
When this switch is depressed, white balance will be as
stored in Channel A of the camera. The switch lights
when it is selected. When AWC Switch !1 is pressed
after selecting AUTO/ATW, A, white balance is automat-
ically adjusted and stored in Channel A.
!0 White Balance Bch Selection Switch
[AUTO/ATW, B]
When this switch is depressed, white balance will be as
stored in Channel B of the camera. The switch lights
when it is selected. When AWC Switch !1 is pressed
after selecting AUTO/ATW, B, white balance is automat-
ically adjusted and stored in Channel B.
!1 Auto White Start Switch [AWC]
If this switch is pressed when AUTO/ATW A Switch o
or AUTO/ATW B Switch !0 is selected, white balance is
automatically adjusted.
stored in Channel A or B. This switch is invalid if the
MODE BAR/CAM Switch r is in the BAR position.
Auto Set Indicator !3 flashes while AWC is in operation,
and goes out when white balance has been properly
adjusted. Auto Set Indicator !3 remains lit if white bal-
ance adjustment fails.
Note: White balance may not be adjustable if there is no
white in the image being taken by the camera. For
details, refer to the Operating Instructions for the
Camera.
The switch lights
The adjustment results are
!2 Auto Black Start Switch [ABC]
When this switch is depressed, the lens iris is automati-
cally closed to set black balance. Be sure to keep the
IRIS AUTO/MANU Switch @5 in the AUTO position in
setting black balance.
while ABC is in operation, and goes out when black bal-
ance has been properly adjusted. Auto Set Indicator !3
remains lit if black balance adjustment fails. Black bal-
ance adjustment may fail if the total pedestal is too low.
In such a case, adjust the total pedestal with T.PED
Control !9 (referring to the OPERATING PROCE-
DURES at page 25) and try to adjust black balance
again.
!3 Auto Set Indicator
This LED flashes during white balance or black balance
adjustment with AWC Switch !1 or ABC Switch !2
depressed, and goes out when the adjustment has
ended normally. The LED remains lit if balance adjust-
ment fails.
!4 Scene File Selection Switch [SCENE FILE, 1/2/3/4]
Select a scene file preset on the camera side.
Remember, however, that [4] is camera scene file
USER A or USER B (provided that WV-E550 or AW-
E560 is connected).
!5 5 6 6 Genlock Phase Control Switch
[G/L PHASE, ON/OFF]
Used to adjust the genlock phase in operating the cam-
era in external sync mode. Set the switch to the ON
position only when adjusting the genlock subcarrier
phase or genlock horizontal phase. Otherwise, keep the
switch in the OFF position.
!6 6 Genlock Subcarrier Phase Coarse Switch
[G/L PHASE, 0°/90°/180°/270°]
Used for coarse adjustment of the colour phases of gen-
lock input and video output signals in operating the cam-
era in external sync mode. Used in combination with
G/L PHASE SC Control !7 , the switch has an adjust-
ment range of over 360°.
Switch !5 to the ON position before adjusting the colour
phases with this switch.
2
Auto Set Indicator !3 flashes
Set G/L PHASE ON/OFF