Panasonic AW-RP501 Service Manual page 6

!7 Genlock Subcarrier Phase Fine Control
[G/L PHASE, SC]
Used for fine adjustment of the colour phases of genlock
input and video output signals in operating the camera
in external sync mode. Use this switch in combination
with G/L PHASE Coarse Switch !6 . Set G/L PHASE
ON/OFF Switch !5 to the ON position before adjusting
the colour phases with this switch.
!8 G/L Horizontal Phase Adjustment Control
[G/L PHASE, H]
Used to adjust the horizontal phases of genlock input
and video output signals in operating the camera in
external sync mode. Set G/L PHASE ON/OFF Switch
!5 to the ON position before adjusting the horizontal
phases with this switch.
!9 Total Pedestal Level Control [T. PED]
The set pedestal level of the camera's Y (luminance)
signal can be adjusted. This control is used in a system
of two or more cameras to adjust the pedestal levels of
these cameras. The control may operate not continu-
ous sometimes due to digital signal processing.
@0 Cable Compensation Luminance Control
[CABLE COMP, Y]
Used to adjust the Y (luminance) signal level of video
output signals as appropriate to the cable length
between the pan/tilt head and this control panel. To
adjust it, first set MODE BAR/CAM Switch r to the BAR
position, then connect a waveform monitor, vec-
torscope, or other measuring instrument to the video
signal output. If the cable between the pan/tilt head and
this control panel is longer than 300 meters, set the
cable compensation switch on the pan/tilt head to the
ON position in advance.
OPERATING PROCEDURES at page 25 or to the
Operating Instructions for the Pan/tilt Head.)
adjust the Y (luminance) signal level with this control,
then adjust the C (chrominance) signal level with
CABLE COMP C Control @1 .
Repeat this until the video output level of this control
panel matches the camera output level.
Turning this control changes not only the Y (luminance)
signal level but also the whole video signal level.
(For details, refer to the
First,
@1 Cable Compensation Chrominance Control
[CABLE COMP, C]
Used to adjust the C (chrominance) signal level of video
output signals as appropriate to the cable length
between the pan/tilt head and this control panel. To
adjust it, first set MODE BAR/CAM Switch r to the BAR
position, then connect a waveform monitor, vec-
torscope, or other measuring instrument to the video
signal output. If the cable between the pan/tilt head and
this control panel is longer than 300 meters, set the
cable compensation switch on the rotary head to the ON
position in advance. (For details, refer to the OPERAT-
ING PROCEDURES at page 25 or to the Operating
Instructions for the Pan/ Tilt Head.) First, adjust the Y
(luminance) signal level with CABLE COMP Y Control
@0 , then adjust the C (chrominance) signal level with this
control. Repeat this until the video output level of this
control panel matches the camera output level.
@2 Tally Indicator [TALLY]
Lights red when a tally signal is input to TALLY Terminal
#9 from a Special Effect Generator (SEG) or video
switcher.
@3 Lamp Indicator [LAMP]
Lights red when LAMP ON/OFF Switch @4 is in the ON
position. Flashes if the lamp connected to the AC
Adapter (AW-PS300) for pan/tilt head is broken. Goes
out when LAMP ON/OFF Switch @4 is set to the OFF
position.
Note: Use a halogen lamp of 250 W to 500 W to connect to
the Pan/tilt Head AC Adapter (AW-PS300). If a lamp of
lower than 250 W is connected to it, the LED may flash
when LAMP ON/OFF Switch @4 is in the ON position
even though the lamp is not broken.
@4 Lamp Switch [LAMP, ON/OFF]
Switches on and off the halogen lamp connected to the
lamp AC receptacle of the Pan/tilt Head AC Adapter
(AW-PS300). Set it to the ON position to switch the
halogen lamp on (in which case, the lamp LED flashes).
Set it to the OFF position to switch the halogen lamp off.
@5 Lens Iris Selection Switch [IRIS, AUTO/MANU]
When this switch is in the AUTO position, the lens iris is
automatically controlled according to the quantity of light
entering the lens.
3