Remaining Risks - Holzmann SB4132SM User Manual

REMOVE ADJUSTING KEYS AND WRENCHES
Form a habit of checking to see whether adjusting keys, wrench-
es and other objects are removed from the machine before turn-
ing it on.
DO NOT FORCE THE MACHINE
It will do a better job when being used within its power range it
has been constructed for. Do not misuse the machine or parts of
it for jobs for which it was not intended.
USE PROPER EXTENSION CORD
Make sure your extension cord is in good condition. When using
an extension cord, be sure to use one with sufficient cross-sec-
tion to carry the current your machine will draw. An undersized
cord will cause a drop in the line voltage resulting in power loss
and overheating.
USE ONLY RECOMMENDED AND SAFE ACCESORIES
Use only accesories matching with the machines specifications
and being suitable for the use with the machine. Especially im-
portant are the max. allowed revolution speeds for which the
accesory is allowed to be used. Use only Accesories whose max.
allowed revolution speed is higher than the max. speed of the
machine you intend them to use with.
DRILL SAFETY
Do not drill workpieces that are too small to be supported safely.
For smaller workpieces you should install a vice onto the working
table and support the workpiece with the vice.
HAZARD FROM DUST
SOME DUST CREATED by power sanding, sawing, grinding, drill-
ing and other construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead based paint
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically-treated lumber.
• Your risk from those exposures varies, depending on how of-
ten you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with ap-
proved safety equipment, such as those dust masks that are
specifically designed to filter out microscopic particles.
WORK SAFETY RULES
Finally obey all general working safety rules imperative when
operating a machine and follow all rules and regulations being
in power in your country regarding safety at work, accident pre-
vention, first aid, fire prevention.
www.holzmann-maschinen.at
DRILL SPECIFIC SAFETY RULES
Take care to remove the Chuck key from the drill chuck before
turning the machine on.
The drill bit shall not touch the workpiece when turning the ma-
chine on.
Especially workpieces with not even surface have to be clamped
by a vice.
Never change, remove, adjust workpiece while machine is run-
ning.
INTENDED USE
This vertical drill press is designed for performing vertical drills
with max. diameter of 20mm and max. drilling depth of 100mm
into suitable materials under the premise to use the correct com-
bination of drill bits, spindle speed and feed rate.
Stainless steel can be drilled up to a diameter of 16mm
The intended use incorporates sufficient knowledge of the opera-
tor regarding the work with drill presses and regarding accident
prevention rules, sufficient material knowledge as well as suf-
ficient maintenance.
Any manipulation of the machine is a misuse, in this case HOLZ-
MANN-Maschinen and its sales partners cannot be made liable
for ANY direct or indirect damage.
It is imperative to obey all safety rules as well as assembly, op-
eration and maintenance instructions to keep alive your guaran-
tee rights.

REMAINING RISKS

The work with a drill press always incorportates some remaining
risks which can never be eliminated entirely and the operator
should be aware of:
Hazard of severe injury when touching the rotating drill bit, drill
chuck or spindle.
Hazard of cutting injury caused by sharp drill edges or sharp
metal chips.
Hazard of injury through material or parts of the workpiece be-
ing catapulted away.
SECURITY DEVICES
The drill press is equipped with an ON/OFF switch with a emer-
gency OFF cap activating the red OFF button when being de-
pressed.
The drill press has an automatic OFF switch which is activated as
long as the drive belt cover is not closed entirely
The drill press is equipped with a chip protection cover which
should be always used when performing drills.