Fitting The Flue Connection Piece; Fresh Air Intake; Closed Combustion System - SCAN 1005 Series Assembly And Instruction Manual

FITTING THE FLUE CONNECTION PIECE

The insert is prepared for a top flue outlet from the factory, but the connection piece can be turned around for a rear outlet.
Mount the connecting piece on the insert, after it has been placed in the cassette.
If the radiation plate was removed before the mounting, remember to put it back in place before putting the burn chamber back
into the cassette.
Mount the gasket 3 x 8 mm at the edge of the flange of the connecting piece. Fasten the connecting piece with the flanged nuts
Gasket
Montage røgstuds
EMNE:

FRESH AIR INTAKE

Scan 1005
NAVN:
MATERIALE:
AREAL:
In a well-insulated house, the air used up by the burning process has to be replaced. This particularly applies to houses with
DIMENSION:
mechanical ventilation. There are different ways of making sure that an air exchange takes place. The most important thing is to
C:\Working Folder\Designs\Scan 1005\91005028.idw
STI:
ensure that there is a supply of air to the room where the wood stove is located. The external wall vent must be located as close
to the wood stove as possible, and you must be able to close it when you are not using the wood stove.
Scan 1005
NAVN: EMNE:
National and local building regulations must be followed with regard to the connection of fresh-air intake.
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 1005\91005028.idw
STI:

CLOSED COMBUSTION SYSTEM

You should use the closed combustion system for the wood-burning stove if you live in a newly-built, airtight home.
External combustion air is connected through a ventilation pipe via the wall or floor.
We recommend mounting a valve in the ventilation pipe in order to avoid condensate in the stove and the pipe system, which can
be closed when the oven is not in use. It can also be an advantage to insulate the ventilation pipe.
Minimum Ø 100 mm ventilation pipe, maximum length: 6 metres with a maximum of 3 bends. We recommend smooth steel pipes.
NOTE: If the stove has a fresh air connexion or closed combustion, the ventilation pipe must be open, when the stove
is in use!
18
Radiation plate
TG.NR:
Montage røgstuds
EMNE:
N/A 26-04-12
VÆGT: DATO:
N/A
VÆGT:
N/A
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
N/A
AREAL:
Montage røgstuds
N/A
VÆGT:
N/A
AREAL:
4 x flange nuts M6
Montage røgstuds
Scan 1001
NAVN: EMNE:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 1001\91001025.idw
STI:
91001025
91005028
TG.NR:
BC
SIGN:
16-11-2018 KEN
DATO: SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
91005028
TG.NR:
16-11-2018 KEN
DATO: SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Scan 1005
NAVN: EMNE:
MATERIALE:
DIMENSION:
C:\Working Folder\Designs\Scan 1005\91005028.idw
STI:
TG.NR:
VÆGT: N/A DATO: 26-04-12 SIGN:
N/A
AREAL: Krog Iversen & Co A/S
DK-5492 Vissenbjerg©
Montage røgstuds
N/A
VÆGT:
N/A
AREAL:
91001025
BC