Page 1
A S S E M B LY - A N D I N S T R U C T I O N S M A N U A L Scan 1002 Congratulations on your new Scan built-in stove You have purchased a product by one of Europe’s leading manufacturer’s of wood-burning stoves, and we are sure that you will have years of pleasure with your purchase.
C O N T E N T S Table of contents Technical data ......................3 Scan 1002 versions Installation Safety Technical data and dimensions Dimension sketch1 Product registration number Type plate Assembly ........................6 Operating the door Loose parts Additional accessories...
(black glass decor, black trim, and black glass handle) intended. The same applies to the fitting of accessories or extra equipment not supplied by Scan A/S. This could also be the case if Scan 1002 WC parts that are necessary for the operation and safety of the stove are dismantled or removed.
Please make a note of this number at the front page. You will always have to state the number if you contact your dealer or Scan A/S. Scan 1002 Insert fired by solid fuel...
A S S E M B LY Operating the door Loose parts Push down the handle and the door will open. The trim is delivered on the wood pallet together with the insert. In the insert’s combustion chamber you will find the following loose parts: •...
Push the connecting piece in the direction of the arrow and remove it. Scan 1002 is delivered secured to the pallet. It is recommended that you remove the door and take all loose parts out of the combustion chamber before unscrewing the stove from the pallet;...
If you intend to connect your stove to an existing chimney, it makes distributed more evenly around the room. sense to contact an authorised Scan dealer, or a local chimney sweep You must ensure that the requirements for convection areas are met.
Page 9
A S S E M B LY Data to use when building in the insert, see fig. 1 Minimum mea- Scan 1002 surements Building height over flammable floor 450 mm Free height over horizontal flue pipe to insulation material, 600 mm...
Page 12
Clean Air Act require- ments” The Scan 1002 BB//WC/BS have been recommended as suitable for use in smoke control areas when burning wood logs with a modifi- cation to the air valve so that it will not close beyond the 33% open position.
Page 18
Place the bottom stones with the inclined edge turning to the rear The rear burn chamber plates must be mounted so that the holes of and downwards. the plates are placed precisely over the tertiary holes of the insert. Nederste røgvenderplade Scan 1001 NAVN: EMNE: DATO: MATERIALE: VÆGT:...
Page 19
Place the centre of the indicator on the centre of the trim. Stroke a finger over the stickers to ensure that they are fixed Fold the indicator on the middle and remove carefully the foil. correctly. Remove carefully the tape. Kantafdækning Scan 1002 can 1002 91002003 EMNE: TG.NR: 14-06-2012 VÆGT:...
Lighting We recommend the use of fire starters, or similar products, which are available from your Scan dealer. Using fire starters helps to light the wood quicker, and keeps the burning process clean. Never use liquid lighting fuels!e! "Top down"...
I N S T R U C T I O N S F O R H E AT I N G Handling fuels Why you need a chimney The chimney is the wood-burning stove‘s motor; it‘s performance Selecting Wood/Fuel decides how well your stove will work. The draft in the chimney You can use any type of clean, dry, unpainted, and untreated wood creates a vacuum in the wood-burning stove.
Clean your wood-burning stove by dusting with a dry, lint-free cloth. If the topcoat is damaged, you can purchase a repair spray from your authorised Scan dealer. As slight differences in colour are possible, spray a larger area to achieve a natural transition for best results.
• In case of any manipulation of the original state of this Scan • Damp wood product or its accessories. • This warranty is only valid in the country to which this Scan pro- • Not enough wood duct was originally supplied.