Wheel Settings (Wheel 1/2) - Roland FANTOM Series Reference Manual

Settings for the Entire FANTOM
Wheel Settings
(WHEEL 1/2)
Parameter Value
Wheel Assign Source SYS, SCENE
Assignable
Assign the functions controlled by the wheels .
OFF
CC01–31,
Wheel1–2 Assign 33–95
BEND
AFT
Wheel1–2 Range Min 0–127
Wheel1–2 Range Max 0–127
S1/S2/S3 Settings
Parameter Value
S1-S3 Assign Source
SYS, SCENE
Assignable
Assign the functions controlled by the [S1], [S2], and
[S3] buttons .
OFF
CC01–31,
33–95
BEND DOWN
BEND UP
AFT
S1–3 Switch Assign
MONO/POLY
MFX SW
EQ SW
IFX1 SW
IFX2 SW
CHORUS SW
REVERB SW
MASTER COMP
SW
MASTER EQ SW MASTER EQ on/off is assigned .
Specify the behavior of the buttons .
MOMENTARY
S1–3 Switch Mode
LATCH
114
Explanation
Specifies whether the functions
controlled by the wheels are
determined by the system settings
(SYS) or by the settings of the scene
(SCENE) .
No function is assigned .
Controller number 1–31, 33–95
The same effect as moving the pitch
bend lever .
Aftertouch
Specify the lower limit value for the
range of the assigned function .
Specify the upper limit value for the
range of the assigned function .
(S1/S2/S3)
Explanation
Specifies whether the functions
controlled by the [S1], [S2], and [S3]
buttons are determined by the system
settings (SYS) or by the settings of the
scene (SCENE) .
No function is assigned .
Controller number 1–31, 33–95
The same effect as moving the pitch
bend lever to the left .
The same effect as moving the pitch
bend lever to the right .
Aftertouch
Mono/poly switch is assigned .
MFX on/off is assigned .
EQ on/off is assigned .
IFX1 on/off is assigned .
IFX2 on/off is assigned .
CHORUS on/off is assigned .
REVERB on/off is assigned .
MASTER COMP on/off is assigned .
The assigned effect is applied only
while you hold down the button .
The effect is switched each time you
press the button .
Slider Settings
(SLIDER)
Parameter Value
Slider Mode DIRECT, CATCH
Assignable
Assigns the function controlled by the sliders .
OFF
CC01–31,
Slider1–8 Assign 33–95
BEND
AFT
Slider1–8 Range Min 0–127
Slider1–8 Range Max 0–127
Knob Settings
(KNOB)
Parameter Value
Assignable
Assigns the function controlled by the control knobs .
OFF
CC01–31,
Knob1–8 Assign 33–95
BEND
AFT
Knob1–8 Range Min 0–127
Knob1–8 Range Max 0–127
Explanation
Specifies whether control data of
the corresponding position is always
output when you move a slider
(DIRECT) or control data is output
only after the slider position passes
through the current value of the
parameter (CATCH) .
No function is assigned .
Controller number 1–31, 33–95
The same effect as moving the pitch
bend lever .
Aftertouch
Specify the lower limit value for the
range of the assigned function .
Specify the upper limit value for the
range of the assigned function .
Explanation
No function is assigned .
Controller number 1–31, 33–95
The same effect as moving the pitch
bend lever .
Aftertouch
Specify the lower limit value for the
range of the assigned function .
Specify the upper limit value for the
range of the assigned function .