GEIGER GJ56 E11 Series Original Assembly And Operating Instructions

Venetian blind motor with electronic end stop for venetian blinds and exterior blinds

Advertisement

Quick Links

Venetian blind motor:
GEIGER GJ56.. E11 with electronic end stop
For Venetian blinds and exterior blinds
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GJ56 E11 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GEIGER GJ56 E11 Series

  • Page 1 Venetian blind motor: GEIGER GJ56.. E11 with electronic end stop For Venetian blinds and exterior blinds Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
  • Page 2: Table Of Contents

    1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property.
  • Page 3: Intended Use

    GJ 56 Design options Torque in Nm For head rails at least 56 mm GEIGER Venetian blinds motor 4. Safety instructions ATTENTION: Important safety instructions. For personal safety, it is important to follow these instructions. Please keep these instructions for future reference.
  • Page 4: Assembly Note

    A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable.
  • Page 5: Installation Instructions

    7. Installation instructions Prior to installation please check to ensure there is no visible damage to the motor like cracks or open cables. Before fixing please check the strength of the masonry and of the  surface. Head rail opening at top: www.geiger.de...
  • Page 6 Head rail opening at bottom: Gerhard Geiger GmbH & Co. KG | 100W1562 V001 0421...
  • Page 7: Information For The Specialist Electrician

    Attention: the connection diagram of the 4 or 5 pole-connector is different. A 4-pole connecting cable must be used for the motors. The GEIGER Flat4 with light blue ring. The motor might start running unexpectedly if a 5-pole connecting cable with continuous power supply is used.
  • Page 8: Setting Of The End Stops

    Press the programming key of the limit stop switch until, after about 3 seconds, the motor confirms “end position programming activated” with 1 x click-clack. Then release the key. PROG Press programming key for about PROG 3 seconds Gerhard Geiger GmbH & Co. KG | 100W1562 V001 0421...
  • Page 9: Programming/Changing The End Stops

    For an optimal operation of the obstacle detection function, move the blind from bottom to top without interruption, after the programming has been completed. After an obstacle detection (e.g. obstacle or blind frozen to the window sill), the UP direction is blocked. A short command in the DOWN direction releases the UP direction. www.geiger.de...
  • Page 10: What To Do If

    T = -15°C .. +70°C / dry and non-condensing place Humidity Run-time optimized version Subject to technical modifications. Please find information to the ambient temperature range of our GEIGER motors under www.geiger.de geprüfte Sicherheit Gerhard Geiger GmbH & Co. KG | 100W1562...
  • Page 11: Declaration Of Conformity

    Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Roland Kraus | WEEE-Reg.-Nr.
  • Page 12: Notes On Waste Disposal

    They will be happy to assist you. Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen T +49 (0) 7142 9380 | F +49 (0) 7142 938 230 info@geiger.de | www.geiger.de Gerhard Geiger GmbH & Co. KG | 100W1562 V001 0421...

Table of Contents