Gage Bilt GB51 Quick Start Manual

Gage Bilt GB51 Quick Start Manual

Pneumatic installation tool

Advertisement

S/N: 2094 AND ABOVE
GB51
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
PNEUMATIC INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB51 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Gage Bilt GB51

  • Page 1 S/N: 2094 AND ABOVE GB51 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. PNEUMATIC INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp.
  • Page 2 TABLE OF CONTENTS Description Page Warnings ..............................3 Principle of Operation and How to use the GB51 ................4 Description, Operation and Maintenance ..................... 5 Parts Lists ..............................6 Nose Assembly Selection Chart ......................7 EU Conformity and Warranty ......................... 8 2.64 Ø...
  • Page 3: Safety Warnings

    Any repair should the background level was 73.2 dB (A). In this be done by qualified personnel trained on Gage Bilt condition the max level was 81.5 dB (A). Therefore, procedures.
  • Page 4 8. Always hold tool so pulling head is perpendicular to surface of material in which rivet is being installed. Exert firm pressure against rivet during installation. WARNING: ALWAYS DISCONNECT AIR SUPPLY WHEN TOOL IS NOT IN USE TO PREVENT ACCIDENTAL START-UP. S/N: 2094 AND ABOVE Rev 2/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 5 It weighs only 2.50 lbs. (1.13 kg) and can be operated in any position with one hand. The GB51 Riveter is 7.31" (185.7mm) high, has a .740” (18.8mm) stroke and generates a minimum of 1000 lbs. (4.45 kN) of pull at 90 psi (6.2 bar). It operates from 90 psi (6.2 bar)-100 psi (6.9 bar) of air pressure at the tool.
  • Page 6 Back Cap 510118 Head Assembly 510121 O'Ring 400782 Seal 510105 Seat 510125 Dowel Screw 510215 Handle 510322 Actuator 510107 O'Ring 400772 Button Head Screw A-819 S/N: 2094 AND ABOVE Rev 2/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 7 CHERRYM AX® AND M BC® ARE REGISTERED TRADEM ARKS OF CHERRY AEROSPACE. FASTACK® IS A REGISTERED TRADEM ARK OF ALLFAST FASTENING SYSTEM S INC. GAGE BILT CERTIFIES THE GB51 WILL INSTALL THE ABOVE FASTENERS 1) RIGHT ANGLE NOSE ASSEMBLYS MAY REQUIRE MORE THAN ONE PULL.
  • Page 8: Declaration Of Conformity

    THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY. DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. TRUARC IS A REGISTERED TRADEMARK OF TRUARC COMPANY LLC. S/N: 2094 AND ABOVE Rev 2/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

Table of Contents